Event. IDIS DC-E4216WRX-2.8mm
Advertisement
Advertisement
Part 1 - Remote Setup
Settings
Select the
Settings
tab and configure recording settings.
Event
Configure event detection settings.
•
Recording Stream
: Choose a stream to use for recording. It’s possible to designate different streams for different recording modes.
-
Time-Lapse/Pre-Event
: Designate the stream to use for recording in time lapse mode or event mode
(pre-event).
-
Event
: Designate the stream to use for recording in event mode (post-event).
• Recordings saved on the SD memory card can be searched and played back from the IDIS Solution
Suite Compact program or remotely from the remote program. For more information, refer to each program's
operation manual
.
• Video search and playback may not function properly on the remote program while video is being recorded on to the SD memory card.
To remove the SD memory card, unselect the
Record
option and wait 30 seconds before doing so. Removing the SD memory card while recording is in progress of without waiting 30 seconds can damage the system and/or the recording data.
30
Alarm In
Select
Alarm In
to enable alarm in event. With alarm in event enabled, alarm in detections by the alarm in connector will be assumed as events.
Part 1 - Remote Setup
Motion Detection
Select
Motion Detection
to configure motion detection event settings. With motion detection event enabled, motion detections within the designated area will be assumed as events.
•
Title
: Enter the alarm-in device’s name.
•
Type
: Select the alarm in type.
•
Event Action
: Select an alarm in event alert action.
-
Alarm Out
: Select if you wish to generate an alarm out.
-
Send Email:
Select if you wish to send an email.
Select the
Image Attachment
option to attach a
.jpg image of the event detected to the email.
-
Remote Callback:
Select this option to send a message to a remote system and then select which system to send the message to.
• Not supported from the IDIS Web program.
• The camera must be registered to the remote system in order to use the
Remote Callback
feature.
-
Audio Alarm:
Select this option to generate an audio alert and then choose an audio file (.wav).
-
FTP Upload
: Select this option if you wish to upload images to the FTP server.
-
Record
: Select this option to record video.
Event Action
settings must be configured correctly in order to perform event actions.
•
Sensitivity
: Select daytime and nighttime motion detection sensitivity levels. Higher values will result in more sensitive motion detection.
•
Minimum Blocks for Detection
: Select minimum blocks for daytime and nighttime motion detection.
Motion must take place over the selected number of blocks in order for it to be considered as a motion detection event.
•
Motion Zone
: Click
Setup
and define the motion zone using blocks.
-
(Draw)/ (Erase)
: Enable/disable motion detection blocks.
-
(Cell)
: Select/unselect motion detection blocks individually.
-
(Region)
: Select/unselect multiple motion detection blocks.
-
(Fill)
: Select/unselect all motion detection blocks.
31
Part 1 - Remote Setup
•
Motion Ignoring Interval
: With Motion Ignoring
Interval configured, no event log or notification is generated for motions detected during a period of time following a motion detection event.
•
Daytime
: Specify when daytime starts and ends. All other times will be assumed as nighttime.
•
Event Action
: Select a motion detection event alert action.
-
Alarm Out
: Select if you wish to generate an alarm out.
-
Send Email
: Select if you wish to send an email.
Select the
Image Attachment
option to attach a
.jpg image of the event detected to the email.
-
Remote Callback
: Select this option to send a message to a remote system and then select which system to send the message to.
• Not supported from the IDIS Web program.
• The camera must be registered to the remote system in order to use the
Remote Callback
feature.
-
Audio Alarm
: Select this option to generate an audio alert and then choose an audio file (.wav).
-
FTP Upload
: Select this option if you wish to upload images to the FTP server
-
Record
: Select this option to record video.
Event Action
settings must be configured correctly in order to perform event actions.
Trip-Zone
Select
Trip-Zone
to configure trip zone event settings.
With trip zone event enabled, motion detected inside/ outside the selected area will be assumed as an event.
•
Sensitivity
: Select daytime and nighttime motion detection sensitivity levels. Higher values will result in more sensitive motion detection.
•
Trip-Zone
: Click
Setup
and define the trip zone using blocks.
-
(Draw)/ (Erase)
: Enable/disable trip zone blocks.
-
(Cell)
: Select/unselect trip zone blocks individually.
-
(Region)
: Select/unselect multiple trip zone blocks.
-
(Fill)
: Select/unselect all trip zone blocks.
-
Trip Direction
: Define in which direction the motion has to occur in order for it to be considered as an event. Select
In
for movement occurring from outside the trip zone in and
Out
for movement occurring from inside the trip zone out.
•
Motion Ignoring Interval
: With Motion Ignoring
Interval configured, no event log or notification is generated for motions detected during a period of time following a motion detection event.
•
Daytime
: Specify when daytime starts and ends. All other times will be assumed as nighttime.
32
•
Event Action
: Select a trip zone event alert action.
-
Alarm Out
: Select if you wish to generate an alarm out.
-
Send Email
: Select if you wish to send an email.
Select the
Image Attachment
option to attach a
.jpg image of the event detected to the email.
-
Remote Callback
: Select this option to send a message to a remote system and then select which system to send the message to.
• Not supported from the IDIS Web program.
• The camera must be registered to the remote system in order to use the
Remote Callback
feature.
-
Audio Alarm
: Select this option to generate an audio alert and then choose an audio file (.wav).
-
FTP Upload
: Select this option if you wish to upload images to the FTP server.
-
Record
: Select this option to record video.
•
Event Action
settings must be configured correctly in order to perform event actions.
Part 1 - Remote Setup
Audio Detection
Select
Audio Detection
to configure audio detection event settings. With audio detection enabled, an audio detection taking place during the specified activation period will be assumed as an event.
•
Sensitivity
: Define the audio detection sensitivity.
Higher values will result in more sensitive detection.
•
Activation Time
: Specify how long audio has to be detected for it to be considered as an event. Audio detections that do not last for the specified duration of time will not be considered as events.
•
Use Ignoring Time
: Define the event ignoring time.
Audio detections taking place during the defined time range will not be assumed as events.
•
Audio Ignore Interval
: With Audio Ignoring Time configured, no event log or notification is generated for audio detections taking place during a period of time following an audio detection event.
33
Part 1 - Remote Setup
•
Event Action
: Select an audio detection event alert action.
-
Alarm Out
: Select if you wish to generate an alarm out.
-
Send Email
: Select if you wish to send an email.
Select the
Image Attachment
option to attach a
.jpg image of the event detected to the email.
-
Remote Callback
: Select this option to send a message to a remote system and then select which system to send the message to.
• Not supported from the IDIS Web program.
• The camera must be registered to the remote system in order to use the
Remote Callback
feature.
-
FTP Upload
: Select this option if you wish to upload images to the FTP server.
-
Record
: Select this option to record video.
Event Action
settings must be configured correctly in order to perform event actions.
Tampering
Select
Tampering
to configure tampering detection event settings. With tampering detection event enabled, a sudden change in the video, such as due to movement of the camera or covering up of the lens, will be assumed as an event.
•
Sensitivity
: Define the tampering detection sensitivity. Higher values will result in more sensitive detection.
•
Activation time
: Specify how long tampering has to be detected for it to be considered as an event.
Tampering detections that do not last for the specified duration of time will not be considered as events.
•
Use Ignoring Time
: Define the event ignoring time.
Tampering detections taking place during the defined time range will not be assumed as events.
34
•
Event Action
: Select a tampering detection event alert action.
-
Alarm Out
: Select if you wish to generate an alarm out.
-
Send Email
: Select if you wish to send an email.
Select the
Image Attachment
option to attach a
.jpg image of the event detected to the email.
-
Remote Callback
: Select this option to send a message to a remote system and then select which system to send the message to.
• Not supported from the IDIS Web program.
• The camera must be registered to the remote system in order to use the
Remote Callback
feature.
-
Audio Alarm
: Select this option to generate an audio alert and then choose an audio file (.wav).
-
FTP Upload
: Select this option if you wish to upload images to the FTP server.
-
Record
: Select this option to record video.
Event Action
settings must be configured correctly in order to perform event actions.
Part 1 - Remote Setup
System Event
Select
System Event
and configure system event settings. With system event enabled, system status, alarm in status, and disk status will be checked periodically and corresponding alerts will be generated.
•
System Alive
: Select to check the system status and then set up a schedule.
-
Send Email
: Select to send out an email when the system comes on line.
-
Remote Callback
: Select this option to send a message to a remote system when the system comes on line and then select which system to send the message to.
•
Alarm In Bad:
Select to check the alarm in status and then set up a schedule.
-
Send Email
: Select to send out an email if no change is detected in the alarm in status.
-
Remote Callback:
Select this option to send a message to a remote system when the SD memory card is inserted/removed and then select which system to send the message to.
•
Disk In/Out
: Select to check if the SD memory card has been inserted/removed.
-
Send Email
: Select to send out an email when the
SD memory card is inserted/removed.
-
Remote Callback
: Select this option to send a message to a remote system when the SD memory card is inserted/removed and then select which system to send the message to.
•
and
Remote Callback
settings under
Event
Action
must be configured correctly in order to send out emails and messages.
•
Remote Callback
is not supported on IDIS Web.
• The camera must be registered to the remote system in order to use the
Remote Callback
feature.
35
Part 2 - IDIS Web
IDIS Web is a program that allows you to view and search video from remote locations over the Internet and can be accessed on a Microsoft Internet Explorer or Chrome.
System requirements for running IDIS Web are as follows:
OS: Microsoft
®
Windows
®
XP (Service Pack 3) Internet Explorer only , Microsoft
®
Windows
®
Vista (Service Pack 1),
Microsoft
®
Windows
®
7 (Home Premium, Professional, Ultimate), Microsoft
®
Windows
®
8 (Pro, Enterprise)
• CPU: Intel Pentium IV 2.4GHz or above (Core 2 Duo E4600 recommended)
• RAM: 1GB or more
• VGA: 128MB or more (1280x1024, 24bpp or above)
• Internet Explorer: Version 10 or later 32-bit
• Chrome: Google Chrome 22.0.1229.0 or above (59.xxx or above recommended)
1
Launch Internet Explorer or Chrome and then enter the following information in the address bar.
– http://IP Address:Port Number (IDIS Web connection port number selected during camera IP address and port number setup)
– Or http://FEN Server Address/FEN name (FEN Server address and FEN name registered to the FEN Server)
– Or http://web.idisglobal.com (it is required to enter the camera IP address when logging in. If the camera uses the FEN feature, you can enter the FEN name registered to the FEN server instead of the camera IP address after selecting the USE FEN option)
• If the Use HTTPS option has been selected during IDIS Web port number setup, enter https instead of http. If prompted with a security certificate warning, select "Continue to this website (not recommended)." If the IDIS Web login page fails to load, configure Internet Explorer's settings as follows:
– Tools
→
Internet Options
→
Security
→
Custom Level...
→
Medium-high (default) or Medium.
– Tools
→
Internet Options
→
Advanced
→
Security
→
Use TLS 1.0 (select)
• If connecting by entering an IP address and a port number, you can connect by entering just the IP address if IDIS
Web connection port number has been set to 80 (443 when entering https).
• If connecting by entering http://web.idisglobal.com, it is required to enter the Watch port number.
• Contact your network administrator for the IP address of the camera you wish to connect to the IDIS Web pot number.
36
Part 2 - IDIS Web
2
When prompted with the IDIS Web login window, select
LIVE-PORT
or
PLAY-PORT
as the desired mode. Enter the
ID and password and click
LOGIN
to sign in using the selected mode.
•
• IDIS Web does not work with Microsoft
®
Windows
®
8 metro UI.
• Do not close the login window while IDIS Web is running. Switching over to Web Live or Web Search mode can cause a script error, requiring you to restart the IDIS Web program.
• To use IDIS Web on Microsoft Windows Vista or above, launch Internet Explorer by right-clicking on the icon and selecting the
Run as administrator
option. Otherwise, certain IDIS Web functions might not be available.
• When running IDIS Web, the bottom section of the screen may get cut off if the address bar or the status bar is shown.
In this case, change Internet Options so that the address bar or the status bar is hidden. (
Tools
→
Internet Options
→
Security
→
Custom level...
→
Allow websites to open windows without address or status bars
(
Enable
))
• Launching a new version of IDIS Web for the first time can cause Internet Explorer to load information from the previous version. In this case, navigate to
Tools
→
Internet Options
→
General
, delete temporary Internet files, and then restart IDIS Web.
• On Microsoft Windows Vista or above, lowered image transmission rate can prevent the screen from being displayed or updated. In this case, we recommend that you disable the computer's auto tuning function. Open the command prompt as an administrator. (
Start
→
Accessories
→
Command Prompt
→
Right-Click
and then select
Run as administrator
) Type in "
netsh int tcp set global autotuninglevel=disable
"and then press Enter. Restart the computer to apply the change. To enable auto tuning again, launch the command prompt as an administrator and then type in "
netsh int tcp set global autotuninglevel=normal
". Restart the computer to apply the change.
37

Public link updated
The public link to your chat has been updated.
Advertisement