Safety Instructions. Canon XEED 4K501ST, REALiS LCOS 4K501ST

Safety Instructions. Canon XEED 4K501ST, REALiS LCOS 4K501ST

Safety Instructions

Before installing and operating the projector, read this manual thoroughly.

This projector provides many convenient features and functions. Operating the projector properly enables you to manage those features and maintain it in good condition for many years to come.

Improper operation may result in not only shortening the product life, but also malfunctions, fire hazards, or other accidents.

If your projector does not seem to be operating properly, read this manual again, check operations and cable connections, and try the solutions in the

“Troubleshooting” section in the back of this manual. If the problem still persists, contact the Canon Customer Support Center.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT

REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS

INSIDE EXCEPT LAMP REPLACEMENT. REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL.

THIS SYMBOL INDICATES THAT DANGEROUS VOLTAGE

CONSTITUTING A RISK OF ELECTRIC SHOCK IS PRESENT

WITHIN THIS UNIT.

THIS SYMBOL INDICATES THAT THERE ARE IMPORTANT

OPERATING AND MAINTENANCE INSTRUCTIONS FOR THIS

UNIT IN THE OWNER’S MANUAL.

CAUTION

Not for use in a computer room as defined in the Standard for the Protection of

Electronic Computer / Data Processing Equipment, ANSI / NFPA 75.

5

Safety Instructions

Safety Precautions

WARNING:

• THIS APPARATUS MUST BE GROUNDED.

• TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE

THIS APPLIANCE TO RAIN OR MOISTURE.

This projector produces intense light from the projection lens. Do not stare directly into the lens, otherwise eye damage could result. Be especially careful that children do not stare directly into the beam.

Install the projector in a proper position. Otherwise it may result in a fire hazard.

Allowing the proper amount of space on the top, sides, and rear of the projector cabinet is critical for proper air circulation and cooling of the unit. The diagrams shown here indicates the minimum space required. If the projector is to be built into a compartment or similarly enclosed, these minimum distances must be maintained.

SIDE and TOP REAR

50 cm (1.6')

50 cm

(1.6')

50 cm

(1.6')

50 cm

(1.6')

Do not cover the ventilation slots on the projector. Heat build-up can reduce the service life of your projector, and can also be dangerous.

If the projector is unused for an extended time, unplug the projector from the power outlet.

Do not project the same image for a long time.

An afterimage may remain on the LCD panels due to the characteristics of the panels of the projector.

CAUTION ON HANGING FROM THE

CEILING

When hanging the projector from the ceiling, clean the air intake vents and top of the projector periodically with a vacuum cleaner. If you leave the projector unclean for a long time, the cooling fans can be clogged with dust, and it may cause a breakdown or a disaster.

DO NOT SET THE PROJECTOR IN GREASY, WET, OR SMOKY CONDITIONS

SUCH AS IN A KITCHEN TO PREVENT A BREAKDOWN OR A DISASTER. IF

THE PROJECTOR COMES IN CONTACT WITH OIL OR CHEMICALS, IT MAY

BECOME DETERIORATED.

6

Safety Instructions

READ AND KEEP THIS OWNER’S MANUAL FOR LATER

USE.

All the safety and operating instructions should be read before beginning to operate the product.

Read all of the instructions given here and retain them for later use. Unplug this projector from the AC power supply before cleaning. Do not use liquid or aerosol cleaners on the projector. Use a damp cloth for cleaning.

Follow all warnings and instructions marked on the projector.

For added protection of the projector during a lightning storm, or when it is left unattended or unused for long periods of time, unplug it from the wall outlet. This will prevent damage due to lightning and power surges.

Do not expose this unit to rain or use near water... for example, in a wet basement, near a swimming pool, etc...

Do not use attachments not recommended by the manufacturer as they may result in hazards.

Do not place this projector on an unstable cart, stand, or table. The projector may fall, causing serious injury to a child or adult, and serious damage to the projector.

Use only with a cart or stand recommended by the manufacturer, or sold with the projector. Wall or shelf mounting should be carried out in accordance with the manufacturer’s directions, and should use a mounting kit approved by the manufacturers.

An appliance and cart combination should be moved with care.

Sudden stops, excessive force, and uneven surfaces may cause the appliance and cart combination to overturn.

Slots and openings in the rear and front of the cabinet are provided for ventilation, to insure reliable operation of the equipment and to protect it from overheating.

The openings should never be covered with cloth or other materials, and the bottom opening should not be blocked by placing the projector on a bed, sofa, rug, or other similar surface. This projector should never be placed near or over a radiator or heat register.

This projector should not be placed in a built-in installation such as a book case unless proper ventilation is provided.

7

Safety Instructions

Never push objects of any kind into this projector through cabinet slots as they may touch dangerous voltage points or short out parts that could result in a fire or electric shock. Never spill liquid of any kind onto the projector.

Do not install the projector near the ventilation duct of air-conditioning equipment.

This projector should be operated using only the type of power source indicated on the marking label. If you are not sure of the type of power supplied, contact the

Canon Customer Support Center or local power company.

Do not overload wall outlets and extension cords as this can result in fire or electric shock. Do not allow anything to rest on the power cord. Do not locate this projector where the cord may be damaged by people walking on it.

Do not attempt to service this projector yourself as opening or removing covers may expose you to dangerous voltages or other hazards. Refer all servicing to qualified service personnel.

Unplug this projector from the wall outlet and refer servicing to qualified service personnel under the following conditions: a. When the power cord or plug is damaged or frayed.

b. If liquid has been spilled into the projector.

c. If the projector has been exposed to rain or water.

d. If the projector does not operate normally after following the operating instructions. Adjust only those controls that are covered in the operating instructions as improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the projector to normal operating condition.

e. If the projector has been dropped or the cabinet has been damaged.

f. When the projector exhibits a distinct change in performance-this indicates a need for servicing.

When replacement parts are required, be sure the service technician uses replacement parts specified by the manufacturer that have the same characteristics as the original parts. Unauthorized substitutions may result in fire, electric shock, or injury.

Upon completion of any service or repairs to this projector, ask the service technician to perform routine safety checks to determine that the projector is in safe operating condition.

8

Safety Instructions

AC Power Cord Requirement

The AC Power Cord supplied with this projector meets the requirements for use in the country you purchased it.

AC Power Cord for the United States and Canada:

The AC Power Cord used in the United States and Canada is listed by the Underwriters Laboratories (UL) and certified by the Canadian Standard Association (CSA).

The AC Power Cord has a grounding-type AC line plug. This is a safety feature to ensure the plug fits into the power outlet. Do not try to tamper with this safety feature. Should you be unable to insert the plug into the outlet, contact your electrician.

Ground

THE SOCKET-OUTLET SHOULD BE INSTALLED NEAR THE EQUIPMENT AND

EASILY ACCESSIBLE.

For the U.S. and Canada, LAMP (S) INSIDE THIS PRODUCT CONTAIN

MERCURY AND MUST BE RECYCLED OR DISPOSED OF ACCORDING

TO LOCAL, MUNICIPAL, STATE, PROVINCIAL, OR FEDERAL LAWS.

For lamp recycling and disposal information please call 1-800-OK-CANON for the U.S. and Canada.

Only for European Union and EEA (Norway, Iceland and

Liechtenstein)

These symbols indicate that this product is not to be disposed of with your household waste, according to the WEEE Directive (2012/

19/EU), the Battery Directive (2006/66/EC) and/or national legislation implementing those Directives.

If a chemical symbol is printed beneath the symbol shown above, in accordance with the Battery Directive, this indicates that a heavy metal (Hg = Mercury, Cd = Cadmium, Pb = Lead) is present in this battery or accumulator at a concentration above an applicable threshold specified in the Battery Directive.

This product should be handed over to a designated collection point, e.g., on an authorized one-for-one basis when you buy a new similar product or to an authorized collection site for recycling waste electrical and electronic equipment (EEE) and batteries and accumulators. Improper handling of this type of waste could have a possible impact on the environment and human health due to potentially hazardous substances that are generally associated with

EEE. Your cooperation in the correct disposal of this product will contribute to the effective usage of natural resources.

For more information about the recycling of this product, please contact your local city office, waste authority, approved scheme or your household waste disposal service or visit www.canon-europe.com/weee, or www.canon-europe.com/battery.

9

Safety Instructions

Federal Communication Commission Notice

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and

2. This device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a

Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. The cable with a ferrite core provided with the projector must be used with this equipment in order to comply with Class A of the

FCC Rules. Use of a shielded cable is required to comply with Class A of FCC

Rules. Do not make any changes or modifications to the equipment unless otherwise specified in the instructions. If such changes or modifications should be made, you could be required to stop operation of the equipment.

Warning:

This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.

The cable with a ferrite core provided with the projector must be used with this equipment in order to comply with Class A .

Use of a shielded cable is required to comply with Class A .

10

Safety Instructions

Safety Symbols in this Manual

This section describes the safety symbols used in this manual. Important projector safety information is identified by the following symbols. Always observe the safety information by these symbols.

Denotes the risk of death or serious injury from improper handling if the information is not observed. To ensure safe use, always observe this information.

Denotes the risk of injury from improper handling if the information is not observed. To ensure safe use, always observe this information.

Denotes the risk of burns from improper handling if the information is not observed. To ensure safe use, always observe this information.

Denotes prohibited actions.

Denotes required actions or information that must be observed.

11

Safety Instructions

Precautions for Use

As this section contains important safety-related information, be sure to read the following carefully beforehand in order to use your projector correctly and safely.

During installation, keep the projector plug easily accessible so that the projector can be unplugged immediately if necessary, or keep a circuit breaker within reach.

If the following situations occur, turn the power off, remove the power plug from the power outlet and contact the Canon Customer Support Center. Failure to do so could cause a fire or result in an electric shock.

If smoke is emitted

If an unusual smell or noise is emitted

If water or other liquid has entered the projector

If metal or any other foreign material has entered the projector

If the projector is knocked over or dropped and the cabinet is damaged

Pay attention to the following points for handling the power cord. Failure to do so may cause a fire, electric shock or personal injury.

Do not place any objects on the power cord and do not allow it to become trapped under the projector.

Do not cover the power cord with a carpet.

Do not modify or excessively bend, twist, pull, wind, or bundle the power cord.

Keep the power cord away from heaters and other sources of heat.

Do not use a damaged power cord. If the power cord is damaged, purchase a replacement from your dealer.

The power cord included with this projector is for use exclusively with this product. Do not use this cord for other products.

12

Safety Instructions

Pay attention to the following points regarding the power source, power plug and handling of the connector. Failure to do so may cause a fire, electric shock or personal injury.

Do not use any power source with a voltage other than the voltage indicated

(AC 100–240 V).

Do not pull the power cord and be sure to hold the power plug or connector when removing. Incorrect handling may damage the power cord.

Do not insert any metal objects into the contact parts of the power plug or connector.

Do not remove the power plug or connector with wet hands.

Insert the power plug and connector securely up to the base. Additionally, do not use a damaged power plug or an outlet that is loose.

Before using an extension cord, check carefully to avoid exceeding the cord’s rated capacity.

Periodically inspect the power plug and outlet and remove any dust or dirt from between the plug and the outlet.

Installation and Handling Precautions

Pay attention to the following points regarding installation and handling of the projector.

Failure to do so may cause a fire, electric shock or personal injury.

Do not use the projector where it might get wet, such as outdoors or by bathtubs or showers.

Do not place containers containing a liquid on top of the projector.

Do not touch the projector itself, the power cord, or the cable if lightening strikes.

Do not move the projector until you have switched off the power, removed the power plug from the power outlet and unplugged any other cables.

Unplug the projector before cleaning or maintenance.

13

Safety Instructions

Pay attention to the following points regarding installation and handling of the projector.

Failure to do so may cause a fire, electric shock or personal injury.

Do not remove the cabinet from the projector or disassemble it. The interior of the projector contains high-voltage components as well as parts that are hot. If inspection, maintenance or repair is required, contact the Canon

Customer Support Center.

Do not disassemble or modify the projector (including consumable parts) or the remote control.

Do not look directly into the exhaust vents during use.

Do not insert any object into vents in the projector, such as the air intake vent or exhaust vents.

Do not place a pressurized can in front of the exhaust vents. The pressure of the contents of the can may increase due to heat from the exhaust vents and this could result in an explosion.

When cleaning off dust or dirt from the projector lens etc., do not use any kind of spray that is flammable. As the temperature of the lamp inside the projector is high, it could ignite, causing a fire.

As strong light beams are emitted while the projector is in use, do not look directly into the projector lens. Doing so could cause an eye injury. Pay particular attention to prevent small children from doing so.

Light from the projector is classified as

Risk Group 2 (RG2) according to

IEC 62471-5:2015.

RG2

When setting the projector on a high surface for projection, be sure the surface is flat and stable.

For ceiling mounting precautions, refer to the installation manual included with the ceiling mount (sold separately).

Precautions on the Lamp

This projector uses a high-pressure mercury lamp, which must be handled carefully and correctly as described below.

The mercury lamp has the following characteristics.

The lamp will gradually become darker over time.

Impact, abrasion, or use of worn-out lamps may cause lamps to rupture (accompanied by a loud noise) or burn out.

Lamps are more likely to rupture after the lamp replacement message is displayed (see

“Replacing the Lamp” ( P171 )). Replace the lamp with a new one as soon as possible.

Useful life of lamps varies widely from lamp to lamp and depending on the environment of use. Some lamps may fail or rupture soon after they are first used.

Be prepared by keeping a spare lamp.

14

Safety Instructions

Note the following precautions during lamp replacement or when a lamp has ruptured.

Failure to do so could result in an electric shock or personal injury.

Before replacing the lamp, always unplug the projector and wait at least an hour.

Ruptured lamps may scatter shards of glass inside the projector. Contact the

Canon Customer Support Center for cleaning and inspection of the projector interior and lamp replacement.

Precautions when replacing lamps that stop working

If illumination suddenly stops, either when you turn the projector on or after it has been on for a while, the lamp may have ruptured. In this case, never attempt to replace the lamp by yourself. Always request service from the

Canon Customer Support Center.

With ceiling-mounted projectors, the lamp may fall out when you open the lamp cover, or during replacement. During replacement, stand to the side of the lamp cover, not directly under it.

If the lamp ruptures, dust and gas (containing mercury vapor) may come out of the exhaust vents. If this happens, immediately open the windows and doors to provide ventilation to the room.

If you accidentally inhale gas from the lamp or get any pieces in your eyes or mouth, consult a doctor immediately.

Precautions for the Batteries of the Remote

Control

Pay attention to the following points regarding handling of batteries. Failing to do so could result in a fire or personal injury.

Do not heat, short circuit or disassemble the batteries, or place them in a fire.

Do not attempt to recharge the batteries that are included with the remote control.

Remove the batteries when they are flat or when the remote control will not be used for a long period of time.

When replacing the batteries, replace both at the same time. Also, do not use two batteries of a different type at the same time.

Insert the batteries with the + and - terminals in the correct directions.

If any liquid from inside the batteries leaks out and contacts your skin, be sure to wash the liquid off thoroughly.

15

Safety Instructions

Pay attention to the following points regarding installation and handling of the projector.

If the projector will not be used for a long period of time, be sure to remove the power plug from the power outlet to ensure safety.

Failure to do so presents a risk of fire if dust accumulates on the plug or outlet.

Parts of the cabinet around and above the exhaust vents may become hot during projection. Touching these areas during operation could cause burns to the hands. Pay particular attention in preventing young children from touching these parts.

Additionally, do not place any metal objects around or above the exhaust vents. Due to the heat from the projector, doing so could cause an accident or personal injury.

Do not place the projector where it may be exposed to oily smoke or steam, such as near kitchen counters or humidifiers. Doing so may cause fire or electric shock.

Do not place any heavy objects on top of the projector or sit / stand on it. Pay particular attention to prevent small children from doing so. The projector may be knocked over and this could result in damage or a personal injury.

Do not place the projector on an unstable or slanted surface.

Doing so may cause the projector to fall or be knocked over and could result in a personal injury.

Do not place any objects in front of the lens during projection. Also, do not start projection with the lens cap on. Doing so could cause a fire.

Presenters in front of the projector should stand where the light does not seem too bright, and where their shadow does not fall on the screen.

When handling the lamp, pay attention to the following points.

Be sure not to handle the lamp immediately after it has been used. Be sure to switch off the power and wait for approximately

1 hour for the lamp and the projector to cool down sufficiently.

Failure to do so could result in a burn or personal injury due to heat from the lamp or projector.

16

Safety Instructions

Ceiling Attachment Part No.: RS-CL15 (Option)

Make sure the followings when you install and handle the ceiling attachment. Otherwise, it may result in fire, electric shock or injury.

Make sure to prepare stable scaffolding when installing the ceiling attachment.

Make sure to fully insert the power plug and connectors when connecting the projector. Never use a damaged plug or loosen outlet.

Make sure to tighten screws for the ceiling attachment securely and never loosen or remove them.

Never look into a lens when adjusting the projection because a high-intensity light is projected from the projector. It may result in eye damage.

During projection, never put an object in front of the projector’s lens.

Make sure the followings when you install and handle the ceiling attachment.

Make sure to ask the Canon Customer Support Center if you want to install the ceiling attachment. An inappropriate installation may cause an accident.

Always check ceiling strength before installation. The installation area on the ceiling must be strong enough to hold the weight of the projector and ceiling mount (including extension pipe). If the ceiling is not strong enough, install sufficient reinforcements. The projector may cause injury if it falls.

Have two or more people help when carrying or installing the projector, and be careful not to drop it or pinch your fingers.

When installing the projector, take measures to keep the projector attached in the event of movement or an earthquake, as by a wire or cable. The projector may cause injury if it falls.

17

Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement

Table of contents