Before Use. Canon XEED 4K501ST, REALiS LCOS 4K501ST

Before Use. Canon XEED 4K501ST, REALiS LCOS 4K501ST

Before Use

Included Accessories

Before use, make sure the following items are included in the package.

Remote control (part No.: RS-RC05)

Batteries for the remote control (AA size x2)

Lens cap

The RS-RC05 can also be used as a

wired remote. ( P34 )

Power cord (1.8 m / 5.9')

For Continental

Europe

User’s Manual (CD-ROM)

For the U.S.A. and Canada

Important Information

Warranty Card

Lens Cap

Lens cap

Always remove the lens cap before projection. Accidentally leaving the lens cap on during projection may distort the lens cap and damage the projector.

25

Before Use

Part Names

Projector

Front Side

Terminals and connectors ( P30 )

Power cord connector (

P59

)

LED indicators ( P28 )

Air intake vent

Air filter (

P169

)

Do not block the air intake.

Doing so may cause a malfunction.

Anti-theft lock hole

An anti-theft wire cable (not included) can be connected.

Side control (

P27

)

Infrared remote receiver (

P34

)

Rear Side

Projection lens

Always remove the lens cap before projection.

Failure to do so may cause a malfunction.

Adjustable feet ( P36 )

Air intake vent

Do not block the air intake.

Doing so may cause a malfunction.

Exhaust vent

Do not block the air exhaust.

Doing so may cause a malfunction.

Lamp cover (

P173

)

Infrared remote receiver ( P34 )

Security bar

A wire or cable can be attached to deter theft.

26

Side Control

(1) (2) (3) (4) (5) (6)

Before Use

(7)

(1) POWER button ( P60

,

P79

)

Turns the projector on or off.

(2) INPUT button ( P63 )

Switches the input signal.

(3) LENS button (

P67

)

Each time the button is pressed, the adjustment window changes, from focus (

P67

) to zoom (image size) (

P68

) to lens shift (image

position) ( P70 ).

To adjust the image, use the [ ] /

[ ] or [ ] / [ ] buttons.

After the focus adjustment window, the marginal focus adjustment window is also displayed for adjusting focus of image edges

( P165 ), depending on the [Marginal

focus] setting ( P113

).

(4) KEYSTONE button ( P73 )

Corrects keystone distortion.

(5) OK button ( P86 )

Determines the item selected from the menu.

(6) Pointer / VOL buttons ( P85

)

Up, down, left, or right in menu navigation or other operations.

Adjust the sound volume.

[ ] VOL– button: Decreases the volume.

[ ] VOL+ button: Increases the volume.

(7) MENU button ( P84

)

Displays a menu on the screen.

27

Before Use

LED Indicators

The projector status is shown by the LED indicators (off / lit / flashing).

POWER (green) : Lights up or flashes under normal conditions when the power is on.

STAND BY (red) : Lights up or flashes during standby or when the projector is shutting down.

WARNING (red) : Lights up or flashes when an error occurs.

LAMP (orange) : Lights up or flashes when a problem occurs with the lamp or lamp cover.

TEMP (red) : Lights up or flashes when the internal temperature is high.

28

Before Use

LED Indicator Displays

Projector operating status is indicated by five LEDs, as shown in the following table.

For details on warnings, see “LED Indicator Details” ( P187 ).

: Off : Lit : Flashing Example of when the POWER indicator is on;

LED indicator

POWER

(green)

STAND BY

(red)

WARNING

(red)

LAMP

(orange)

TEMP

(red)

Operating status

Projector not plugged in.

In standby mode.

Resuming operation (projection) after standby.

Cooling down while entering standby or power management mode from power on.

Power is on. (Projecting.)

In power management mode, with the lamp off. (Flashes green and then red.)

The time for replacing the lamp is near. (In standby mode.)

The time for replacing the lamp is near. (During projection)

Internal temperature is high. (In standby mode.)

Internal temperature is high. (During projection)

A lamp error has occurred.

A temperature error has occurred.

The lamp cover is open.

Flashes 3 times: An air filter error has occurred.

Flashes 4 times: A fan error has occurred.

Flashes 5 times: A power error has occurred.

A flashing LAMP indicator means that it is almost time to replace the lamp. Prepare a replacement lamp.

29

Before Use

Input Terminal

(1) (2)

(3) (4) (5) (6) (7) (8)

(1) HDMI terminal (HDMI) (

P52 ,

P53

)

Receives digital video signals (HDMI).

Carries both video and audio signals across a single cable.

(2) Digital PC / DVI-D terminal (DVI-D) ( P52 )

Connects the external monitor output from a computer.

Receives digital PC signal (Digital PC).

(3) Service port (CONTROL) ( P184 )

Used for executing user commands ( P185 –

P186 ).

(4) LAN port (

P130

)

Connects the LAN cable (shielded twisted pair).

Used to connect the projector to a network.

(5) USB port (

P129 )

Connects a USB flash drive. Used for firmware updates.

(6) AUDIO IN terminal (AUDIO IN) (

P52 )

Receives audio input. Audio supplied to this terminal is played through the internal speaker when you select [Audio in] as the source audio terminal for the selected source video.

(7) AUDIO OUT terminal (AUDIO OUT) ( P52 ,

P53

)

Outputs the selected audio signal. (Connecting an audio cable to this terminal mutes the speaker.)

(8) Terminal for wired remote control (REMOTE) (

P34

)

This terminal is used to connect the remote control using a cable.

30

Remote Control

The remote control allows you to operate all functions of the projector.

Before Use

(1)

(2)

(3)

(4)

(5)

(6)

(7)

(8)

(9)

(10)

(11)

(12)

(1) POWER button (

P60

, P79 )

Turns the projector on or off.

(2) ASPECT button ( P72 ,

P96

)

Changes the aspect ratio mode.

(3) Pointer buttons (

P85 )

Selects the upper, lower, left or right item in the menu.

(4) OK button ( P86

)

Determines the item selected from the menu.

(5) ZOOM button (

P68

)

Adjusts the image size.

[ ] / [ ] buttons:

Increase the image size.

[ ] / [ ] buttons:

Decrease the image size.

(6) FOCUS button ( P67

)

Adjusts focusing.

[ ] / [ ] buttons:

Moves the focus position further away.

[ ] / [ ] buttons:

Moves the focus position nearer.

By pressing the

FOCUS

button twice, you can adjust the focus at image edges (

P165

).

[Marginal focus] setting ( P113

).

(7) TEST PATTERN button ( P117 )

Displays the test pattern.

(8) D.ZOOM button

Not used with this product.

(9) Ch button ( P123 )

Changes the remote control channel when the remote control is used via the infrared transmitter.

(10) IMAGE button (

P76 )

Switches the image mode (image quality).

(11) AUTO PC button

Not used with this product.

(12) INPUT button (

P63

)

Switches the input signal.

31

Before Use

(13) Change input buttons

Change the input signal between Digital

PC and HDMI.

ANALOG 1

,

ANALOG 2

and

COMPONENT

are not used with this product.

(14) MENU button ( P84 )

Displays a menu on the screen.

(15) EXIT button ( P86 )

Cancels functions such as menu display or test pattern during operation and returns to the image display.

(16) SHIFT button ( P70 )

Shifts the image up, down, left, or right.

[ ] / [ ] / [ ] / [ ] buttons:

Moves the image.

(17) KEYSTONE button ( P73

)

Corrects keystone distortion.

The [Keystone] setting enables both horizontal/vertical keystone correction

(by adjusting top/bottom/left/right length) and corner correction.

(18) VOL button

Adjusts the sound volume.

[ ] button, [3] button:

Increases the volume.

[ ] button, [6] button:

Decreases the volume.

(19) MUTE button

Mutes the sound.

(20) Numerical buttons (

P128

, P132 ,

P134

)

Enter password and TCP/IP setting values.

(21) Fn button

Not used with this product.

(22) BLANK button ( P80 )

Temporarily blacks out the image.

(23) FREEZE button (

P80

)

Freezes the projected image.

(24) Terminal for wired remote control (

P34 )

Connects a cable to the projector for remote control operation.

(13)

(14)

(15)

(16)

(17)

(18)

(19)

(20)

(21)

(22)

(23)

(24)

32

Before Use

Preparing the Remote Control

1

Installing Remote Control Batteries

Open the battery compartment lid.

Raise the battery cover tab while pushing it.

2

Insert batteries.

Insert 2 new AA batteries in the compartment with the

+ and – terminals positioned correctly.

3

Close the compartment lid.

Insert the tab into the remote control notch

(1) and push the battery cover down

(2).

(1)

(2)

• If buttons on the remote control are inoperative when you attempt to operate the projector, replace the batteries with new ones.

• Do not drop the remote control or subject it to impact.

• Do not spill any liquids on the remote control. Doing so may cause a malfunction.

Pay attention to the following points when handling the batteries.

Failing to do so could result in a fire or personal injury.

• Do not heat, short circuit or disassemble the batteries, or place them in a fire.

• Do not attempt to recharge the batteries that are included with the remote control.

• Remove the batteries when they are flat or when the remote control will not be used for a long period of time.

• When replacing the batteries, replace both at the same time. Also, do not use two batteries of a different type at the same time.

• Insert the batteries with the + and - terminals in the correct directions.

• If any liquid from inside the batteries leaks out and contacts your skin, be sure to wash the liquid off thoroughly.

33

Before Use

Remote Control Operating Range

The remote control is an infrared type. Point it at the infrared remote receiver on the front or rear of the projector to operate it.

25°

8 m (26.3')

25°

8 m (26.3')

25°

25°

• Use the remote control within an angle of 25° in any direction from directly in front of the infrared remote receiver.

• The remote control may be inoperative if there is an obstacle between the remote control and the projector or the infrared remote receiver on the projector is exposed to direct sunlight or strong light of lighting equipment.

• When you use 2 or more projectors at the same time, you can change the channel settings to prevent the 2 remote controls from interfering with each other. (

P123

)

Using the Remote (RS-RC05) in a Wired Connection

The remote control can also be used in a wired connection with the projector.

Use a cable with a ø3.5 mm stereo mini jack (not included).

Remote control

(RS-RC05)

Terminal for wired remote control

ø3.5 mm stereo mini jack cable (not included)

• Infrared operations cannot be performed if a cable is connected to the projector or the remote control.

• Use a cable with a ø3.5 mm stereo mini jack (not included) with a length of 30 m (98.4') or less.

34

Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement

Table of contents