8
4. Tighten the locking screw against the bottom collar of the
20 lb LP gas fuel tank to secure.
B
A
C
A. Locking screw
B. Mounting hole
C. Bottom collar
5. Slide the drawer with the 20 lb LP gas fuel tank back into the cabinet. Turn the tank tray locking bracket clockwise 90° to tighten.
A
A. Tank tray locking bracker
Natural Gas Conversion
Conversion must be made by a qualified gas technician. The qualified Natural gas technician shall provide the Natural gas supply to the selected grill location in accordance with the
National Fuel Gas Code ANSI Z223.1/NFPA 54 - latest edition, and local codes. For conversion to Natural gas, the Natural Gas
Conversion Kit supplied with the grill (on some models) or the
Natural Gas Conversion Kit Part Number 710-0003 must be used.
See “Assistance” section for information on ordering.
IMPORTANT: The gas installation must conform with local codes, or in the absence of local codes, with the National Fuel Gas Code,
ANSI Z223.1/NFPA 54 - latest edition.
Follow instructions for converting to Natural gas in the “Gas
Conversions” section of this manual or the instructions supplied with Natural Gas Conversion Kit Part Number 710-0003.
The gas supply line shall be equipped with an approved shutoff valve. This valve should be located in the same area as the grill and should be in a location that allows ease of opening and closing. Do not block access to the shutoff valve. The valve is for turning on or shutting off gas to the grill.
B
A
C
A. Gas supply line
B. Shutoff valve “open” position
C. To grill
INSTALLATION INSTRUCTIONS
Freestanding Outdoor Grill Installation
WARNING
2. Remove the warming shelf and grill grates from inside the grill and remove the package inside the firebox.
3. Remove foam block and wrap from inside the grill.
Excessive Weight Hazard
Use two or more people to move and install grill.
Failure to do so can result in back or other injury.
Unpack Grill
1. Remove all packaging materials and remove grill from the shipping base.
2. Move grill close to desired outdoor location.
3. Open the grill hood.
Remove Packaging Material Inside the Grill
1. Use a utility knife to cut yellow straps and packing tape to open box from top and remove the boxes.
4. Replace the grill grates.
5. Place warming shelf on brackets as shown.
B
A
A
A. Warming shelf brackets
B. Warming shelf
Attach Right Side Shelf
1. Unpack side shelf.
2. Loosen the 2 screws on the side panel and align the bottom keyhole slots on the side shelf with the loosened screws.
Hook the side shelf onto the two loosened screws and let the shelf slide down so the screws are in the narrow neck of the slots.
5. Attach the side shelf to the control panel (C) by tightening the screw from the side shelf control panel to the main control panel.
A
B
C
6. Attach side shelf push bar by aligning the screw holes on the side shelf with the screw holes in the push bar. Insert the screws into the push bar screw holes and then into the side shelf and tighten.
IMPORTANT: This step is meant to help with the installation, but do not depend solely on the two screws to hold the weight of the side shelf.
3. Attach the top of the side shelf to the grill (A) by inserting three screws into the side shelf from inside the grill hood and tighten.
4. Attach the bottom of the side shelf to the side panel (B) of the grill by tightening the two screws inserted in the keyhole slots in Step 2.
9
Attach Left Side Shelf
1. Unpack side shelf.
2. Loosen the 2 screws on the side panel and align the bottom keyhole slots on the side shelf with the loosened screws.
Hook the side shelf onto the two loosened screws and let the shelf slide down so the screws are in the narrow neck of the slots.
Attach Condiment Tray
1. Open cabinet door.
2. Insert hooks on condiment tray into mounting holes on cabinet door.
IMPORTANT: This step is meant to help with the installation, but do not depend solely on the two screws to hold the weight of the side shelf.
3. Attach the top of the side shelf (B) to the grill by inserting three screws from under the side shelf into the side panel and tighten.
4. Attach the bottom of the side shelf to the side panel (A) of the grill by tightening the two screws inserted in the keyhole slots in Step 2.
5. Attach the side shelf to the side burner by tightening the screw from the side shelf control panel (C) to the side burner.
A
NOTE: It is recommended to remove the condiment tray when removing or replacing the LP tank.
B
C
10
