advertisement
680 SERIES
which will be recessed into a floor or deck, install so as to permit access to the equipment, either from above or below, for servicing. Make certain that there are no obstructions which would prevent removal of all side cabinet panels and access to the jets components, especially on the side with the equipment bay.
CAUTION:
If the spa is indoors or located in an enclosed area, proper ventilation should be discussed with an Engineer or authority competent enough to understand the necessary provisions needed to vent moist or heated air and air associated with chemical odors outdoors.
When the spa is in use considerable amounts of moisture will escape potentially causing mold and mildew.
This can cause health risk. Over time, this can damage certain surfaces, surroundings, and equipment.
4.1 Outdoor Location
In selecting the ideal outdoor location for your spa, we suggest that you take into consideration the following:
• The proximity to changing area and shelter (especially in regions subject to cold weather).
• The pathway to and from your spa (this should be free of debris so that dirt and leaves are not easily tracked into the spa).
• The closeness to trees and shrubbery (remember that leaves and birds could create extra work in keeping the spa clean).
• A sheltered environment (less wind and weather exposure can result in lowered operation and maintenance costs).
• The overall enhancement of your environment. It is preferable not to place the spa under an unguttered roof overhang since run-off water will shorten the life expectancy of the spa cover.
• For spas that are to rest on balconies, roofs or other platforms not specifically tied into main structural support, consult a professional
Structural Engineer with experience in this type of application.
• In the unlikely event that you should ever need to access or gain entry to any portion of the spa for servicing, it is highly recommended that you plan your outdoor installation to provide full access to the entire spa. Please take this into consideration when placing the spa in a deck or enclosed by a surrounding.
• Consider locating your spa away from any reflective surface or glass to prevent any damage to the synthetic skirt.
• Do not shim the spa. To ensure proper support the spa must sit flat on the intended foundation.
Page 10
advertisement
Related manuals
advertisement
Table of contents
- 7 Important Spa Owner Information
- 7 FCC Notice
- 8 Important Safety Instructions for all Spa Owners
- 12 Entrapment Risk
- 13 Hyperthermia
- 14 Important CSA Safety Instructions (Canada only)
- 14 General Electrical Safety Instructions
- 15 Choosing A Location
- 16 Outdoor Location
- 17 Indoor Location
- 18 Power Requirements
- 18 North American 60 Hz Power Options
- 19 Export 50 Hz Power Options
- 20 Electrical Wiring Instructions
- 24 Spa Fill Up Procedure
- 29 Control Functions
- 29 Control Panel
- 30 General Spa Features And Controls
- 31 and Peyton Models)
- 32 Operating Instructions
- 32 Setting Water Temperature
- 33 Activate Pumps
- 33 SunGlow™ Light Operation (Denali and Tacoma Models)
- 34 (Edison®, Hartford, Hawthorne, and Peyton Models)
- 35 Adjusting Individual Jet Flow
- 35 Selecting Desired Massage Action
- 35 Air Controls
- 35 Optional BLUEWAVE™ Spa Stereo System
- 36 10.0 Automatic Filtration Cycles
- 36 Standard Filtration/Heating Modes (F1-F3)
- 36 Economy Filtration/Heating Modes (F4-F6)
- 36 Lock Modes (L1-L3)
- 36 Selecting The Filtration/Heating Mode
- 37 Filtration Modes
- 38 Water Purification System
- 40 11.0 Spa Maintenance
- 40 Cleaning The Filter
- 41 Draining and Refilling
- 42 Pillow Care (All Models Except Denali)
- 43 Cleaning The Spa Interior
- 43 Maintaining The Cover
- 44 Maintaining The Synthetic Cabinet
- 44 11.7 Winterizing
- 45 Restarting Your Spa in Cold Weather
- 45 12.0 Water Quality Maintenance
- 46 pH Control
- 46 Sanitizing
- 47 ® Water Purification System
- 47 Quartz Tube Maintenance
- 50 13.0 Error Conditions/Error Messages
- 50 Panel Displays SN
- 50 Panel Flashes FL1 or FL
- 51 Panel Displays COL
- 51 Panel Displays ICE
- 51 Panel Displays OH
- 51 Panel Displays
- 51 Panel Displays BLB
- 52 14.0 Troubleshooting Procedures
- 52 None of the Components Operate (e.g. Pump, Light)
- 52 Pump Does Not Operate but Light Does
- 52 Poor Jet Action
- 52 Water is Too Hot
- 52 No Heat
- 54 Circuit Diagram (60 Hz)
- 55 and Peyton Circuit Diagram (60 Hz)
- 56 17.0 Export Denali/Tacoma Circuit Diagram (50 Hz)
- 57 Peyton Circuit Diagram (50 Hz)
- 58 19.0 Optional BLUEWAVE™ Spa Stereo System
- 59 Pairing the Remote and Stereo
- 59 Audio Settings
- 61 Wireless Remote Control Functions
- 62 Electronic Device Connections and Functions
- 65 Wireless Remote Battery Replacement Procedure
- 66 BLUEWAVE Spa Stereo System Specifications
- 66 Stereo Cautions