- Sports & recreation
- Camping, tourism & outdoor
- Above ground pools
- Above ground pool accessories
- Cal Spas
- Portable Spa
- Owner's manual
- 60 Pages
Priming the Pump. Cal Spas Portable Spa
advertisement
Assistant Bot
Need help? Our chatbot has already read the manual and is ready to assist you. Feel free to ask any questions about the device, but providing details will make the conversation more productive.
10
Priming the Pump
New spa owners often have difficulty the first time they start their spa and the pump fails to prime. This can be frustrating, but these simple instructions can help you.
Sometimes air can become trapped in the pump while filling the spa. You will know this has happened when after you have filled and started the spa,
The pump will not work properly while air is trapped in it.
Continuing to operate the pump in this way will cause damage.
the pump does not seem to function. You will hear the pump operating, but no water will be moving.
Starting Up: Priming Mode for NEO-Pack Systems
The system will enter the priming mode.
Priming Mode
will display on the control panel. In Priming Mode, all devices such as jets and lights are operable. Jets can be turned on and off to help prime the pump. The system will exit Priming
Mode and go to the Main display when the RETURN button is pressed, or after four minutes of inactivity.
Exiting Priming Mode for NEO-Pack Systems
You can manually exit Priming Mode by pressing the RETURN button. Note that if you do not manually exit the priming mode, the priming mode will be automatically terminated after 4 to 5 minutes. Be sure that the pumps have been primed by this time.
Bleeding Air from the Pump
If you have tried priming the pump several times unsuccessfully using the control panel, you can bleed the air from the pump manually.
1. Shut off the power to the spa.
2. Using a Phillips screwdriver, remove the front panel from the spa and locate the pump.
3. Close the gate valve on the discharge side of the pump (if your spa is installed with one.)
4. Turn the bleeder valve counter clockwise with a small pair of pliers until the air has been released from the pump.
5. If this is unsuccessful, loosen the union nut on side of the pump with channel locks. When air is bled out, tighten the nut.
6. Turn on power to the spa and press the
JETS
button. If there is still air trapped in the pump, repeat steps 2 through 5 until the pump primes.
www.calspas.com
2018 Portable Spa
LTR20181000, Rev. O
advertisement
Related manuals
advertisement
Table of contents
- 3 Important Safety Instructions
- 4 Pre-Delivery Checklist
- 4 Planning the Best Location
- 5 Preparing a Good Foundation
- 5 Hookup
- 6 240 Volt Electrical Installation
- 7 US & Canada
- 9 120 Volt Electrical Installation
- 9 Testing the 240 Volt GFCI Breaker
- 12 Priming the Pump
- 13 Operating Your Spa
- 13 NEO Control Panel Operation
- 21 ATS Plus Therapy System
- 22 (AAT)
- 22 LED Lighting
- 23 Diverter Knobs
- 23 Air Venturis
- 23 Waterfalls
- 23 Hydro Streamer Waterfall
- 24 Water Clarity
- 25 Water Testing Methods
- 26 Adding Chemicals to the Spa Water
- 28 2. Sanitation and Shock
- 29 3. Filtration
- 30 4. Regularity (Maintenance Schedule)
- 30 Generic Names for Chemicals
- 31 Common Water Chemistry Questions
- 32 Do’s and Don’ts
- 33 Bather Load
- 33 Ozonator
- 34 Troubleshooting Water Clarity Problems
- 35 Bromine Generator
- 36 Generator
- 37 System
- 37 Removing and Reseating the Pillows
- 37 Jet Removal and Replacement
- 38 Draining Your Portable Spa
- 39 Winterizing (Cold Climate Draining)
- 39 Cleaning and Replacing the Filter
- 40 Spa Cover and Locking System
- 40 Vacation Care
- 41 Cleaning Your Spa
- 41 Using the Freedom Sound System
- 42 Appendix
- 42 Replacement Parts
- 55 Basic Troubleshooting
- 57 “Thermal Creep
- 58 Limited Warranty
- 60 Warranty Registration