- Sports & recreation
- Camping, tourism & outdoor
- Above ground pools
- Above ground pool accessories
- Cal Spas
- Portable Spa
- Owner's manual
- 60 Pages
Bather Load. Cal Spas Portable Spa
advertisement
Assistant Bot
Need help? Our chatbot has already read the manual and is ready to assist you. Feel free to ask any questions about the device, but providing details will make the conversation more productive.
Bather Load
“Bather Load” is the term used to describe the number of people using a spa, combined with the length of usage, and the frequency of usage. All these factors have a great effect on the spa water. The higher the bather load, the more chemicals need to be added and a longer filtration time will be needed.
Recommendations are designed for spas with average bather load (3 to 4 people, 15 minutes of usage, three times a week at 100 degrees) If your bather load exceeds these guidelines, and you experience water quality problems, increase the amount of filtration first, (go to the next higher filtration number) then if water quality is still not adequate, consult the advice of your Cal Spas dealer for additional chemical or system recommendations. Be sure to give them your bather load information.
Ozonator
The ozone generator releases ozone into the spa water. You will still need to test for chlorine or bromine and occasionally replenish it to return the sanitizer level to the baseline. See page 26.
For spas without a circulation pump, pump 1 will run at low speed and the ozonator will run during filtration. You will need to increase your filtration to a minimum of six hours per day.
For spas with a circulation pump, the ozonator will run with the circulation pump.
The spa’s control system is factory-programmed with one filter cycle that will run in the evening when energy rates are often lower. The time and duration of the filter cycle can be set according to your needs. In addition, a second filter cycle can be enabled. Filtration time may need to be increased with heavy bather load.
See instructions for setting filtration cycles on page 14.
Always make sure water diverter valves are turned all the way to the left or right and never left in the center position during filtration cycles. When the diverter valve is in the center position, there is not enough suction from the pump in order to inject ozone into the spa. The ozonator will generate ozone, but it will not be injected into the water.
31
2018 Portable Spa
LTR20181000, Rev. O
www.calspas.com
advertisement
Related manuals
advertisement
Table of contents
- 3 Important Safety Instructions
- 4 Pre-Delivery Checklist
- 4 Planning the Best Location
- 5 Preparing a Good Foundation
- 5 Hookup
- 6 240 Volt Electrical Installation
- 7 US & Canada
- 9 120 Volt Electrical Installation
- 9 Testing the 240 Volt GFCI Breaker
- 12 Priming the Pump
- 13 Operating Your Spa
- 13 NEO Control Panel Operation
- 21 ATS Plus Therapy System
- 22 (AAT)
- 22 LED Lighting
- 23 Diverter Knobs
- 23 Air Venturis
- 23 Waterfalls
- 23 Hydro Streamer Waterfall
- 24 Water Clarity
- 25 Water Testing Methods
- 26 Adding Chemicals to the Spa Water
- 28 2. Sanitation and Shock
- 29 3. Filtration
- 30 4. Regularity (Maintenance Schedule)
- 30 Generic Names for Chemicals
- 31 Common Water Chemistry Questions
- 32 Do’s and Don’ts
- 33 Bather Load
- 33 Ozonator
- 34 Troubleshooting Water Clarity Problems
- 35 Bromine Generator
- 36 Generator
- 37 System
- 37 Removing and Reseating the Pillows
- 37 Jet Removal and Replacement
- 38 Draining Your Portable Spa
- 39 Winterizing (Cold Climate Draining)
- 39 Cleaning and Replacing the Filter
- 40 Spa Cover and Locking System
- 40 Vacation Care
- 41 Cleaning Your Spa
- 41 Using the Freedom Sound System
- 42 Appendix
- 42 Replacement Parts
- 55 Basic Troubleshooting
- 57 “Thermal Creep
- 58 Limited Warranty
- 60 Warranty Registration