- Home
- Domestic appliances
- Large home appliances
- Cooker hoods
- ELICA
- ERS630S1
- Installation instructions
Installation Instructions. ELICA ERS630S1 , ERS636S1 , ERS636S1, ERS630S1
Add to my manuals
44 Pages
advertisement
Installation Instructions
Venting Methods
Determine which venting method is best for your application.
Vent system can terminate either through the wall or floor.
Island locations
Front (standard) mounted blower motor
Rear mounted blower motor
(Reversible version)
C C
B
A
A. Down vent
B. Cooktop
C. Aspiration plate
Built-in cabinet locations
B
A
Island locations
Vent systems installed under a concrete slab using PVC sewer pipe.
Front (standard) mounted blower motor
B
A
D
M
L
C
F
E
G
H
K J I
Rear mounted blower motor (reversible aspiration plate)
B
A
D
M C
E
F
G
L H
A. Down vent
A
B
B. Left vent C. Right vent
C
K J
A. Wall cap
B. 6” (15.2 cm) round metal vent
C.16” (40.6 cm) maximum
D. 6” (15.2 cm) round PVC swer pipe
E. 6” (15.2 cm) round metal vent transition with damper (supplied)
F. 6” (15.2 cm) round PVC coupling
G. Concrete slab
H. 6” (15.2 cm) round PVC sewer pipe
I
I. 6” (15.2 cm) round 90º PVC sewer
pipe elbow
J. Tightly pack gravel or sand
completely around pipe
K. 6” (15.2 cm) round 90º PVC sewer
pipe elbow
L. 6” (15.2 cm) round PVC coupling
M. 12” (30.5 cm) minimum
Installing the vent system
WARNING
Excessive Weight Hazard
Use two or more people to move and install downdraft vent.
Failure to do so can result in back or other injury.
1.
Place cardboard or similar material on top of a flat surface where you can easily assemble the downdraft vent system.
2.
Remove parts packages, downdraft vent and blower box from the
carton.
3.
Remove all shipping materials, tape and film from the downdraft vent and blower box.
4.
Install the right and left undercounter mounting brackets to the vent box. Slide the keyhole slots over the guide tabs and push the brackets up to set them in place.
A
B
5.
Attach the end cap to the vent box, depending on what vent position you choose (standard or reversible). Place the tabs into the mounting slots at each end of the downdraft vent as shown and push down to lock into place.
A
B
C
D
A. Vent box
B. Undercounter mounting bracket
C. Keyhole slots
D. Guide tabs
A. Standard installation cap
B. Reversible installation cap
NOTE: Only one cap must be mounted A or B
7
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 3 Important safety Notice
- 4 Electrical & Installation requirements
- 4 Before installing the hood
- 5 List of Materials
- 5 Parts supplied
- 5 Parts not supplied
- 5 Product Dimensions
- 6 Countertop Cutout Dimensions
- 6 Venting Requirements
- 7 Installation Instructions
- 8 Determine which vent directioin is best for your installation
- 9 Rear mounting (reversible mode)
- 10 Complete Installation
- 11 Control Installation
- 11 Electrical connection
- 13 Downdraft use
- 13 Vent system care
- 14 Troubleshooting
- 15 Warranty
- 17 Avis de sécurité important
- 18 Exigences électriques et d’installation
- 19 Outils et piéces
- 19 Pièces fournies
- 19 Pièces non fournies
- 19 Dimensions du produit
- 20 Dimensions des ouvertures à découper
- 20 Exigences concernant l’évacuation
- 21 Instructions d’installation
- 22 Déterminer la meilleure orientation de l’évacuation pour l’installation
- 23 Montage arriére (mode réversible)
- 24 Achever l’installation
- 25 Raccordement électrique
- 27 Utilisation du système d’extraction par le bas
- 27 Entretien du système d’évacuation
- 28 Dépannage
- 31 Aviso de seguridad importante
- 32 Requisitos eléctricos y de instalación
- 33 Lista de Materiales
- 33 Partes suministradas
- 33 Partes necesarias
- 33 Dimensiones del producto
- 34 Dimensiones de corte de la cubierta de cocina
- 34 Requisitos de ventilación
- 38 Complete la Instalación
- 39 Instalación del control
- 39 Conexión eléctrica
- 41 Uso de la campana
- 41 Cuidado de la campana
- 42 Solución de problemas
- 43 Garantía