- Home
- Domestic appliances
- Large home appliances
- Cooker hoods
- ELICA
- ERS630S1
- Installation instructions
Determine which vent directioin is best for your installation. ELICA ERS630S1 , ERS636S1 , ERS636S1, ERS630S1
Add to my manuals
44 Pages
advertisement
6.
Measure distance “X” from the cabinet floor to the top of the countertop. Subtract 28
1
⁄
2
” from distance “X” to determine dimension “Y” (X - 28
1
⁄
2
= Y).
Top of countertop
Left or right venting:
1.
Using two or more people, place the downdraft vent system on its
back.
2.
Remove the 4 screws from the cover plate mounted to the face of the motor box and set them aside.
Downdraft vent
28
1
⁄
2
”
(73 cm)
“X”
B
C
A
“Y”
Cabinet floor
7.
Attach the support legs to the side of the vent box with
4 - 4 x 8 mm screws in each support leg. Adjust to dimension
“Y” from the bottom of the vent box to the bottom of the support legs. Tighten screws.
G
F
E
A
C
B dim. “Y”
A. Motor box
B. Support leg
C. Installation screws
Determine which vent direction is best for your installation
When installed in a cabinet, vent system can exhaust through the bottom, right or left of the cabinet.
IMPORTANT:
When using the 6” (15.2 cm) vent transition (supplied) for 6” round venting, only left or right venting is recommended.
Bottom venting
NOTE:
If installing the vent damper in the down position, a wall or roof cap with a damper at the exit end of the vent system is required.
•
Downdraft vent is shipped with blower in down venting position so no modification is required.
•
If rear mounting of the blower motor is not required, go to the
“Complete Installation” section.
•
To mount the blower motor to the rear side of the vent box, go to the “Rear Mounting (reversible mode)” section.
D
A.Cover plate
B. Cover plate screws
C. Cover plate keyhole slot shoulder screws
D.Motor mounting screws
E. Vent cover plate
F. Motor box
G. Vent cover screws
3.
Slide the cover plate up and slip it over the keyhole slot shoulder screws. Set the cover aside.
4.
Remove 4 screws from the bottom of the motor box that hold the motor assembly to the motor box.
NOTE: Disconnect the electrical wiring connection from motor if
needed.
5.
Remove 3 screws and the vent cover plate from the left or right side of the motor box for the venting direction to be used.
6.
Rotate the blower motor assembly 90 degrees to the left or right side to the chosen venting direction and secure to the blower box with motor mounting screws previously removed. Do not twist or bind the wires.
7.
Install the vent cover plate over the rectangular opening in the bottom of the motor box and secure with vent cover screws.
NOTE: Reinstall the electrical wiring connection to motor if
removed.
8.
Reinstall the cover plate to the face of the motor box and secure with 4 cover plate screws previously removed.
8
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 3 Important safety Notice
- 4 Electrical & Installation requirements
- 4 Before installing the hood
- 5 List of Materials
- 5 Parts supplied
- 5 Parts not supplied
- 5 Product Dimensions
- 6 Countertop Cutout Dimensions
- 6 Venting Requirements
- 7 Installation Instructions
- 8 Determine which vent directioin is best for your installation
- 9 Rear mounting (reversible mode)
- 10 Complete Installation
- 11 Control Installation
- 11 Electrical connection
- 13 Downdraft use
- 13 Vent system care
- 14 Troubleshooting
- 15 Warranty
- 17 Avis de sécurité important
- 18 Exigences électriques et d’installation
- 19 Outils et piéces
- 19 Pièces fournies
- 19 Pièces non fournies
- 19 Dimensions du produit
- 20 Dimensions des ouvertures à découper
- 20 Exigences concernant l’évacuation
- 21 Instructions d’installation
- 22 Déterminer la meilleure orientation de l’évacuation pour l’installation
- 23 Montage arriére (mode réversible)
- 24 Achever l’installation
- 25 Raccordement électrique
- 27 Utilisation du système d’extraction par le bas
- 27 Entretien du système d’évacuation
- 28 Dépannage
- 31 Aviso de seguridad importante
- 32 Requisitos eléctricos y de instalación
- 33 Lista de Materiales
- 33 Partes suministradas
- 33 Partes necesarias
- 33 Dimensiones del producto
- 34 Dimensiones de corte de la cubierta de cocina
- 34 Requisitos de ventilación
- 38 Complete la Instalación
- 39 Instalación del control
- 39 Conexión eléctrica
- 41 Uso de la campana
- 41 Cuidado de la campana
- 42 Solución de problemas
- 43 Garantía