2 Unpacking and installation
2. Unpacking and installation
Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
________________________________________________________________________________________
2-1
2. Unpacking and installation
2.1 Unpacking
The monitor is surrounded with foam for transportation protection and packed into a card box. Banding and fastening clips secure the package.
To unpack the monitor,
• Release the fastening clips
• Remove the banding
• Take the monitor out
• Remove the foam.
For later shipment, it is recommended to store the original packaging and to re-use it.
The following components are included in the delivery:
• The monitor itself
• 1 pc power cord (European, with CEE7 power plug)
• 1 pc power cord (American, with NEMA 15-5 (ANSI 73.11) power plug)
• 1 pc user's manual
• 1 pc Infra red remote control unit
• 1 pc RCA jack
• 1 pc DVI-D 24 pin cable
• 1 pc D-Sub 15 pin cable
• 1 pc S-Video Mini Din 4 pin cable
• 1 pc cable adapter Mini Din 8 pin to 3xRCA jack (for component video)
2-2 ___________________________________________________________Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
2. Unpacking and installation
2.2 Installation
Installation and preliminary adjustments should be performed by qualified Barco personnel or authorized Barco service dealers.
Installation of the monitor shall comply with the safety instructions as listed in chapter
1.3.1 Safety on installation
• Make sure that the installation place has sufficient stability!
• Do not place the monitor near heat sources!
• Use maximum 15mm/0.59 inch long screws. Longer screws may damage the monitor!
• Ensure that the display is operating within the specified operating range +5°C – +40°C | 41°F – 104°F, at max.
90% RH, non-condensing.
• Never restrict airflow into the display by blocking any vents or air intakes.
• Leave a clearance on all vented sides of the display to permit the required airflow. Clearance should be minimum 15 cm but may be larger depending on the ambient environment.
Do not install the unit where it may be easily touched or leaned against. Avoid locations subject to high vibrations or severe impacts. Do not install the unit where it is exposed to humidity, oil, smoke or excessive dust.
2.2.1 Accessories
The product portfolio of accessories comprises a table stand, and wall and ceiling mounts. The installation of the accessories is described in the installation section. The following chapter just gives a rough idea about mounting the table stand.
2.2.2 Mounting of the table stand (optional)
The table stand is an optional component.
The monitors feature on their rear side 2 parallel arrangements of 4 threads each. These threads comply with the
VESA standards, their horizontal and vertical distance is 200mm. They are equipped with the respective screws
(M8x15).
These screws are used to attach the table stand!
• Lay the monitor upside down on a clean(!) surface, bottom edge flush with e.g. edge of the table.
Soil or particles laying on the surface may irretrievably damage the screen of the monitor!
Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
________________________________________________________________________________________
2-3
2. Unpacking and installation
• Take a screwdriver for recessed head screws, size 8.
• Remove the 4 center screws and washers on the rear side of the monitor.
• Take the table stand and attach its mounting plate to the rear of the monitor using the previously removed screws and washers.
Mind the correct orientation of the table stand!
• When the screws are fastened tightly, put up the monitor
2-4 ___________________________________________________________Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
2.2.3 Dimensions of the 42" monitor:
2.2.3.1 Front view
2. Unpacking and installation
2.2.3.2 Side view and rear view:
123.7
Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
________________________________________________________________________________________
2-5
2. Unpacking and installation
2.2.4 Dimensions of the 47" monitor:
2.2.4.1 Front view
1139.4
2.2.4.2 Side view and rear view:
125
2-6 ___________________________________________________________Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
2. Unpacking and installation
2.3 Examining the monitor
2.3.1 Front view
An LED on the bottom right edge indicates the operating status of the monitor.
LED indicator
Orange
Green
Mode
Standby
In operation
Next the to LED indicator the sensor to receive the commands from the IR control unit is located as well as the
light sensor to determine the surrounding light intensity.
Take care that the sensors are not blocked by any objects placed in front of the monitor!
The preset for dim adjustment and bright adjustment can be set and controlled via the OSD, cf. 5.6.4 L .
2.3.2 Side view
ENTER
>/+
</-
Menu
The control elements of monitors are located on the right (seen from front). The 7 push buttons allow switching the monitor from and to standby, to adjust volume and to activate and operate the OSD.
Refers to Item
1
2
3
4
5
6
7
ENTER
>/+
</-
Menu
Function
Standby / switch into operation
Activate selection
Scroll right for menu items / volume increase
Scroll left for menu items / volume decrease
Scroll down for menu ite
ms /
Access signal input menu
Scroll up for menu items
OSD control menu button / Access or exit main menu /
Access or exit submenu / Exit selection
Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
________________________________________________________________________________________
2-7
2. Unpacking and installation
2.3.3 Rear view
On the rear, all interfaces as well as the power connector and the main power switch are located.
The standardized power socket is conform to IEC-320-13 and allows connecting local power cables. The internal power supply is auto ranging from 100VAC to 240VAC.
The monitor allows connecting the following sources:
Input
Video system input
RGB input
HD-SDI input *)
HD-SDI output *)
Signal receive&transmit
Audio
VIDEO IN
S-VIDEO
Interface
RCA
S-Video Mini Din 4pin signals
NTSC/PAL
NTSC/PAL
YUV (Y Pb/Cb Pr/Cr) Component Mini Din 7 pin NTSC/PAL
RGB Analog D-Sub 15 pin RGB analog
RGB Digital
Serial Digital
DVI-D 24 pin
BNC
RGB digital
SDI / HD-SDI
Serial Digital
RS232 IN
RS232 OUT
BNC
D-Sub 9 pin
D-Sub 9 pin
RCA
(red: right (R), white: left (L))
SDI / HD-SDI
Audio in (L+R)
Audio out(L+R) (2x) and
Subwoofer
The pin assignments of the interfaces are listed in chapter
7.6 Interfaces and chapter
8.6 Interfaces,
respectively.
HDSDI/SDI IN HDSDI/SDI OUT RS232/OUT RS232/IN
L/OUT1 L/OUT2 L/IN MAIN POWER AC IN
VIDEO
IN
S-VIDEO
Y
Pb/Cb
Pr/Cr DVI RGB IN
ON
OFF
SW R/OUT1 R/OUT2 R/IN
Two sources can be viewed simultaneously in either PIP mode (Picture-in-Picture) or PAP mode (Picture-and-
Picture). In case more than one source is connected, the active sources and the display mode (one source or two sources) are selected via the OSD.
*)
Only LCS-42 and LCS-47 feature the HD-SDI interfaces!
2-8 ___________________________________________________________Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
2. Unpacking and installation
2.4 Cabling
All interfaces are located on the rear of the system!
Check the power rating on your outlet before connecting the monitor to the wall outlet or to a power strip. Contact your facilities manager or a qualified electrician if you are not sure what type of power is supplied to your building.
The devices are designed to operate with single-phase power systems having a grounded neutral conductor. To reduce the risk of electrical shock, do not plug into any other type of power system.
• Use the power cord delivered with your system:
• Plug in the female power connector into the male connector AC IN on the rear of the monitor.
• Plug in the CEE7-plug (or ANSI 73.11 plug) into the wall outlet.
The power input is auto-ranging from 100VAC to 240 VAC.
• Connect the video and RGB sources with the respective interface using the included cables.
2.5 Switching on and off
Use the main power switch on the rear of the system to power the system on and off.
When the monitor is powered on, it can be switched into operation or switched to standby, respectively, using eater the top most push button on the rear right side of the monitor or using the IR remote control unit (RCU).
If the system is not operated for longer periods, it is recommended to switch it off using the main power switch on the rear side and to disconnect it from the wall outlet.
When the monitor is powered off by switching off the main power switch, the front LED indicating the operating mode is off! Also you cannot switch the unit into operation by using the remote control unit or the top most push button.
To power on the unit, switch on the main power switch on the rear of the system. The LED indicator will be turned on, and you can switch the monitor into operation either by using the RCU or the top most push button the rear of the system.
Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
________________________________________________________________________________________
2-9
2. Unpacking and installation
2.6 Inserting batteries into the Infrared remote control unit
The batteries are not yet inserted in the remote control to avoid remote control operation in its package, resulting in a shorter battery lifetime.
How to install the batteries:
• Push the cover tab with the fingernail a little backwards (as indicated by the arrow) and pull upwards the cover top.
• Slide the cover forwards to remove-
• Insert two AA size batteries, making sure the polarities match the + and – marks inside the battery compartment.
• Insert the lower tab of the battery cover in the gap at the bottom of the remote control, and press the cover until it clicks in place
Note that there may be laws concerning disposal and recycling of used batteries in your country! Please contact your local authorities to get further information!
Avoid keeping used, old batteries inside the remote control, causing leakage of internal liquid resulting metal rust or fatal damage to the remote control unit.
2-10 __________________________________________________________Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008