11. Compliance statement
11 Compliance statement
11.1 FCC Compliance statement
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions :
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation
Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
______________________________________________________________________________________
11-1
12. Accessories
12 Accessories
The monitor can be equipped with a table stand, or mounted to the wall or the ceiling. The following chapter describes assembling and installation of the accessories.
12.1 Required tools
• Screwdriver for recessed head screws (screw size M8)
Wall mount and ceiling mount:
• Wrench 10mm, 17mm, 19mm
• Allen wrench size 2.5 to adjust the tilt angle of the long/short ceiling mount
• Drilling machine to drill the holes into concrete
• 4 fixation screws per wall mount / ceiling mount
• 1 additional (center) fixation screw for the tiltable wall mount
• 4 (5) dowels (concrete)
The manufacturer of the accessories gives the following recommendation:
Specification of screws for wood: DIN 571 M8x80 4.6
Specification of screws for concrete DIN 16168 M8x75
Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
______________________________________________________________________________________
12-1
12. Accessories
12.2 Table stand
The table stand allows adjusting the monitor in height.
For the 42" version, the lower edge can be set between 14mm and 204mm; for the 47" versions, the lower edge can be set between 14mm and 135mm.
12.2.1 Scope of delivery
The table stand comes fully assembled.
12-2 __________________________________________________________Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
12. Accessories
12.2.2 Installation
The monitors feature on their rear side 2 parallel arrangements of 4 threads each. These threads comply with the
VESA standards, their horizontal and vertical distance is 200mm. They are equipped with the respective screws
(M8x15).
These screws are used to attach the table stand!
• Lay the monitor upside down on a clean(!) surface, bottom edge flush with e.g. edge of the table.
Soil or particles laying on the surface may irretrievably damage the screen of the monitor!
• Take a screwdriver for recessed head screws (screw size M8).
• Remove the 4 center screws and washers on the rear side of the monitor.
• Take the table stand and attach its mounting plate to the rear of the monitor using the previously removed screws and washers.
Mind the correct orientation of the table stand!
• When the screws are fastened tightly, put up the monitor
Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
______________________________________________________________________________________
12-3
12. Accessories
12.2.3 Dimensions
12.2.3.1 Dimensions of the 42" version
12.2.3.2 Dimension of the 47" version
12-4 __________________________________________________________Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
12. Accessories
12.2.4 Height adjustment
The monitor can be adjusted in height by sliding the mounting plate up or down, respectively.
For adjusting the table stand in height, first uninstall the monitor!!
Never loosen the screws for sliding the plate when the monitor is still attached to the table stand! Otherwise the monitor will crash on the table!!
• Uninstall the monitor!
• Remove the 2 fixation screws of the plate to the vertical bar at each side.
• Re-position the monitor.
• Re-attach the screws.
• Install the table stand to the monitor.
Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
______________________________________________________________________________________
12-5
12. Accessories
12.3 Screen bracket (adapter plate)
The installation of the screen bracket is mandatory for fixation of the wall mount, and the ceiling mount..
12.3.1 Scope of delivery
The screen bracket is one component; for its installation the screws on the rear side of the monitor are used.
12-6 __________________________________________________________Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
12. Accessories
12.3.2 Installation
The monitors feature on their rear side 2 parallel arrangements of 4 threads each. The threads comply with the
VESA standards, their horizontal and vertical distance is 200mm. These threads are equipped with the respective
screws (M8x15).
These screws are used to attach the screen bracket!
To install the screen bracket, proceed as follows:
• Lay the monitor upside down on a clean(!) surface.
• Take a screwdriver for recessed head screws (screw size M8).
• Remove the 8 screws and washers on the rear side of the monitor.
• Take the screen bracket, and fix it with the 8 screws and washers as shown below.
The screen bracket is equipped with 3 knurled bolts which are later slid into the fixation plate of the wall mount / ceiling mount. These bolts are arranged in a triangle. Make sure that the screen bracket is fixed with the top of the triangle showing to the bottom of the monitor!
Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
______________________________________________________________________________________
12-7
12. Accessories
12.4 Fixed wall mount
First mount the screen bracket to the monitor, cf.
. Screen bracket (adapter plate)
Use the fixed wall mount to attach the monitor to the wall.
The drawings show the fixation facility itself and a monitor which is equipped with a fixed wall mount.
12.4.1 Scope of delivery
The fixed wall mount comes in one piece. The 4 screws to attach it to the wall have to be provided on site!
12-8 __________________________________________________________Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
12. Accessories
12.4.2 Installation
The wall mount bracket is attached to the wall by means of 4 screws M8 (for specification of the screws, cf.
Required tools .). It is the same bracket for 42" and 47".
For drilling the holes in the wall, it is recommended to use a jig – take a sheet of paper
(A3) and copy the distances given in the drawing below.
• Drill 4 holes, 10mm, to the wall in the given distances!
• Use 4 screws M8 and fix the wall mount to the wall.
• Slid in the knurled bolts of the screen bracket into the keyholes of the wall mount and lock them by turning the lock bar.
Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
______________________________________________________________________________________
12-9
12. Accessories
12.4.3 Dimensions
The following pictures give an overview about the measurements and dimensions of the 42" version and the
47".
12.4.3.1 Dimensions of the 42" version:
12.4.3.2 Dimension of the 47" version:
12-10 _________________________________________________________Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
12. Accessories
12.4.4 Wall pattern
In case of a "monitor wall", the arrangement of the holes in the wall can be taken from the following pictures:
12.4.4.1 Wall pattern 42"
12.4.4.2 Wall pattern 47"
Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
_____________________________________________________________________________________
12-11
12. Accessories
12.5 Tiltable wall mount
First mount the screen bracket to the monitor, cf.
. Screen bracket (adapter plate)
The tiltable wall mount fixes the monitor to the wall and allows setting its position in 5 steps between zero and
20 degrees. The drawings show the tiltable wall mount at max. and min. tilt angle.
12.5.1 Scope of delivery
The tiltable wall mount comes fully assembled. It comprises a front plate and a rear plate. The rear plate will be attached to the wall, the front plate to the screen bracket of the monitor. The angle between the rear plate and the front plate can be set in 5 steps from zero to 20 degrees (angle between wall and monitor display).
12-12 _________________________________________________________Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
12. Accessories
12.5.2 Installation
The rear plate of the tiltable wall mount bracket is attached to the wall by means of 5 screws M8 (for specification of the screws, cf. Required tools .). It is the same bracket for 42" and 47".
For drilling the holes in the wall, it is recommended to use a jig – take a sheet of paper
(A3) and copy the distances given in the drawing below.
• Drill 5 holes, 10mm, to the wall in the given distances!
• Slid in the knurled bolts of the screen bracket into the keyholes of the wall mount and lock them by turning the lock bar.
Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
_____________________________________________________________________________________
12-13
12. Accessories
12.5.3 Dimensions
The following pictures give an overview about the measurements and dimensions of the 42" version and the
47".
12.5.3.1 Dimensions of the 42" version:
12.5.3.2 Dimensions of the 47" version:
12-14 _________________________________________________________Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
12. Accessories
12.5.4 Tilting
To tilt the monitor, the two top screws connecting the rear plate and the front plate have to be removed.
If you want to change the tilt angle of the monitor, first uninstall the monitor!!
Never loosen the screws for setting the tilt angle when the monitor is still attached to the tiltable wall mount!
• Uninstall the monitor!
• Use the included allen wrench 4mm to loosen the left and the right top screws.
• Tilt the front plate to the desired degree.
• Reattach the screws.
• Re-install the monitor.
For security reasons, the two top screws to adjust the tilting angle are applied with a center pin and thus require a special tool. Therefore the allen wrench 4mm is included which feature a center hole for the pin.
Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
_____________________________________________________________________________________
12-15
12. Accessories
12.6 Short ceiling mount
First mount the screen bracket to the monitor, cf.
. Screen bracket (adapter plate)
The short ceiling mount fixes the monitor to the ceiling and allows setting the lower screen edge to a distance of the ceiling between 706.5mm and 885.5mm for the 42" versions, and between 776mm and 955mm for the 47" versions, respectively.
The monitors can be tilted by 20 degrees thanks to the ball point on the ceiling fixation plate.
The drawings show the fixation facility itself and a monitor equipped with the short ceiling mount.
12-16 _________________________________________________________Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
12. Accessories
12.6.1 Scope of delivery
The short ceiling mount comprises 3 parts:
• The base plate with the ball point connection to the adjustable bar. This base plate will be mounted on the ceiling.
• The adjustable bar.
• The adapter plate to attach to the screen bracket of the monitor with two hooks to look the knurled bolts.
The screws to assemble the short ceiling bar are included. You will need a wrench 17mm.
The screws to fix the base plate to the ceiling have to be provided on site, cf. Required tools .
Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
_____________________________________________________________________________________
12-17
12. Accessories
12.6.2 Installation
The short ceiling mount is attached to the ceiling by means of 4 screws M8 (for specification of the screws, cf.
Required tools .). It is the same bracket for 42" and 47".
For drilling the holes in the ceiling, it is recommended to use a jig – take a sheet of paper
(A4) and copy the distances given in the drawing below.
• Drill 4 holes, 10mm, to the ceiling in the given distances!
• Attach the ceiling mounting plate.
• Attach the adjustable bar to the ball joint of the ceiling mounting plate by using one of the included screws
M10x60. Secure the screw with the nut and attach the black plastic cap. Also attach a black plastic cap to the already installed parallel screw on the ceiling mounting plate.
• Slide in the adjustable bar into the monitor mounting plate of the short ceiling mount. Fix its position by one of the included screws M10x60. Secure the screw with the nut and attach the black plastic cap.
12-18 _________________________________________________________Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
12. Accessories
• The knurled bolts of the screen bracket are slid into the keyholes of the wall mount and locked by turning the lock bars.
Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
_____________________________________________________________________________________
12-19
12. Accessories
12.6.3 Dimensions
The following pictures give an overview about the measurements and dimensions of the 42" version and the
47".
12.6.3.1 Dimensions of the 42" version:
12-20 _________________________________________________________Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
12.6.3.2 Dimension of the 47" version:
12. Accessories
12.6.4 Tilting
Use an allen wrench size 2.5mm!
To adjust the tilting angle of the monitor,
• loosen the tilt angle fixation screw,
• adjust the position,
• tighten the screw again.
Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
_____________________________________________________________________________________
12-21
12. Accessories
12.7 Long ceiling mount
First mount the screen bracket to the monitor, cf.
. Screen bracket (adapter plate)
The long ceiling mount fixes the monitors to the ceiling and allows setting the lower screen edge to a distance of the ceiling between 1235.5mm and 1614.5mm for the 42" versions, and between 1305mm and 1684mm for the
47" versions, respectively.
The monitors can be tilted by 20 degrees thanks to the ball point connection.
12-22 _________________________________________________________Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
12. Accessories
12.7.1 Scope of delivery
The short ceiling mount comprises 4 parts:
• The base plate with the cylinder which holds the telescope bar. This base plate will be mounted on the ceiling
• The telescope bar with the ball point connection to adjustable bar.
• The base plate with the ball point connection to the adjustable bar. This base plate will be mounted on the ceiling
• The adapter plate to attach to the screen bracket of the monitor with two hooks to lock the knurled bolts.
The screws to assemble the long ceiling bar are included. You will need a wrench 17mm.
The screws to fix the base plate to the ceiling have to be provided on site, cf. Required tools .
Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
_____________________________________________________________________________________
12-23
12. Accessories
12.7.2 Installation
The wall mount bracket is attached to the wall by means of 4 screws M8 (for specification of the screws, cf.
Required tools .). It is the same bracket for 42" and 47".
For drilling the holes in the ceiling, it is recommended to use a jig – take a sheet of paper
(A4) and copy the distances given in the drawing below.
• Drill 4 holes, 10mm, to the ceiling in the given distances!
• Attach the ceiling mounting plate.
• Slid in the telescope bar and lock its position by means of a screw M10x60. Secure the screw with a nut, and apply the black plastic cap.
• Complete the ball point connection between the telescope bar and the adjustable bar by using one of the included screws M10x60. Secure the screw with the nut and attach the black plastic cap. Also attach a black plastic cap to the already installed parallel screw on the telescope bar.
• Slide in the adjustable bar into the monitor mounting plate of the long ceiling mount. Fix its position by one of the included screws M10x60. Secure the screw with the nut and attach the black plastic cap.
12-24 _________________________________________________________Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
12. Accessories
• Hook in the knurled bolts of the monitor into the notches and the keyhole of the long ceiling adapter plate.
Lock the monitor by means of the left and right hook.
Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
_____________________________________________________________________________________
12-25
12. Accessories
12.7.3 Dimensions
The following pictures give an overview about the measurements and dimensions of the 42" version and the
47".
12.7.3.1 Dimensions of the 42" version:
12-26 _________________________________________________________Barco - LC series - R5976934 - user's manual - Revision 08 - April 2008
