Table of Contents
Safety Instructions
Connecting the
Projector to
Network (SX80 II)
Before Use
Projecting an Image
Useful Functions Available During a Presentation
Setting Up Functions from Menus
Projecting an Image from a Digital Camera or an
USB Flash Memory (SX80 II)
Connecting the Projector to Network (SX80 II)
Appendix
Index
125
Setting an IP Address (SX80 II)
It is possible to send an error notification e-mail ( P135 ) from the projector to the computer
when you connect the projector to the network.
To connect via the network, an IP address must be assigned to the projector. Set an IP address by following the steps below. (The examples shown are Windows XP screenshot images.)
■Setting IP Address of the Computer
1
Connect the projector and a computer directly via a cross or straight type LAN cable.
Commercial cross or straight type LAN cable
2
Turn on the power of the projector and computer.
3
Open [Control Panel] from the [Start] menu, then select [Network and Internet Connections] - [Network Connections].
4
Right-click [Local Area Connection], and open [Properties].
5
Select [Internet Protocol (TCP/IP)] and click the [Properties] button. Take notes of the original network settings (IP address, subnet mask, DHCP settings, etc).
6
Select [Use the following IP address] and set as follows:
[IP address]: 192.168.254.1
[Subnet mask]: 255.255.255.0
7
When you have specified the settings, click the [OK] button and then click the [OK] button on the [Local Area Connection Properties] window to close it.
126
Setting an IP Address (SX80 II)
■Resetting the IP Address Setting of the Computer
1
Turn off the projector and remove the LAN cable.
2
Follow the step 3 to 6 to restore the network setting to the original setting.
127
Setting Network (SX80 II)
■Displaying the Network Configuration Screen
1
Turn on the computer and projector
.
2
Launch a web browser, enter "http://192.168.254.254" in the address bar, and press the Enter key .
The password input screen appears.
The supported web browsers is Microsoft Internet Explorer 6 or later.
3
In the password input screen, enter "root" for [User name] and "system" for [Password] and click the [OK] button.
The projector network configuration screen appears on the web browser.
The following information is displayed.
[Projector name]: The name of the projector on the network
[Location]:
[MAC address]:
The location of the projector
The MAC address of the projector
[IP address]:
[Power Status]:
The IP address of the projector
The power status of the projector
[Lamp Time Normal Mode]:The total lamp used time in its normal mode
[Lamp Time Quiet Mode]: The total lamp used time in its quiet mode
[Lamp Time Converted]: The total lamp used time (converted value)
[Filter Time]: The total filter used time
Click the [Settings] button to display the menu screen.
128
Setting Network (SX80 II)
■Setting the Network
1
In the menu screen, click [Password], input the new user name and password, and click the [OK] button.
Setting items:
[User name]:
[New password]:
The user name for logging in the network
The new password
[Confirm new password]: The password for confirmation
2
Click [TCP/IP], enter appropriate values in the following field, and click the [OK] button.
Setting items:
[IP address]:
[Subnet mask]:
[Default gateway]:
The IP address of the projector
The subnet mask of the projector
The default gateway of the projector
129
Setting Network (SX80 II)
3
Click [Mail], enter appropriate values in the following field for the error report, and click the [OK] button.
Setting items:
[To:]:
[Cc:]:
The E-mail address to which the error report is sent
(Within 63 alphanumeric characters)
The E-mail address to which the carbon copy of the error report is sent (Within 63 alphanumeric characters, can be
[From:]: omitted)
The sender of the E-mail (the projector)
[SMTP server IP address]: The IP address of the available SMTP mail server
[SMTP server port number]: The port number of the available SMTP mail server
[SNTP server IP address]: The IP address of the available SNTP mail server (can be omitted)
[Time zone]:
[Mail resend interval]:
The time zone of the installation site
The E-mail resending interval at a transmission failure
[Mail resend times]:
[Error report]:
Setting range: 0 - 59 seconds (the factory default: 10 seconds)
The number of E-mail resending attempts at a transmission failure
Setting range: 0 - 255 times (the factory default: 3 times)
Turning ON/OFF the error report sending function (the factory default: [OFF])
130
Setting Network (SX80 II)
4
If the SMTP mail server authentication is required, click [Mail auth], enter appropriate values in the following field, and click the [OK] button.
Select one of the following four authentication method in [Mail authentication]. Select
[OFF] if the mail authentication is not required (the factory default is [OFF]).
[LOGIN (SMTP authentication)], [CRAM-MD5 (SMTP authentication)],
[USER/PASS (POP before SMTP)], [APOP (POP before SMTP)]
Setting items:
[User name]:
[Password]:
[Confirm password]:
[POP3 server IP address]:
[POP3 server port number]:
The user name for the mail authentication
The password for the mail authentication
The password for confirmation
The IP address of the POP3 server
The port number of the POP3 server
(The factory default: 110)
[POP before SMTP response time]: The wait time between the POP3 authentication and the transmission to the SMTP mail server
(millisecond, the factory default: 300)
131
Setting Network (SX80 II)
5
If you want to monitor the projector, click [SNMP], enter appropriate values in the following field, and click the [OK] button.
Select one of the following four SNMP version in [SNMP]. Select [OFF] if you don't want to monitor the projector.
(The factory default: [OFF])
[V1], [V2c], [V3 (MD5)], [V3 (DES, MD5)]
Setting items:
[Receive community]:
[Password]:
[Confirm password]:
[SNMP trap]:
[Trap IP address]:
[Trap community]:
The name of the community (user)
The password for the community setting
The password for confirmation
Conditions for sending the SNMP trap
The IP address to which the SNMP trap is sent
The name of the community (user) to which the SNMP trap is sent
What is the SNMP Agent Function?
This projector supports the SNMP (Simple Network Management Protocol) agent function that monitors the status of the projector. SNMP consists of the manager (a monitoring tool, your PC) and agent (a monitored target, the projector).
The information exchange group via SNMP is called "a community." The message which tells the status of the agent is called "a SNMP trap."
This projector has the following SNMP traps:
• Cold start: it tells the SNMP agent is under initialization.
• Warm start: it tells the SNMP agent is under reset (at the SNMP version upgrade).
• Authentication failure: it tells that it failed the SNMP authentication.
• Faulty lamp: it tells that a lamp-related error was occurred.
• Faulty power supply: it tells that a power supply-related error was occurred.
• Temperature abnormality: it tells that a temperature-related error was occurred.
• Lamp status change: it tells that the status of the lamp used time was changed.
• Faulty cooling fan:
• Faulty lamp cover: it tells that a cooling fan-related error was occurred.
it tells that a lamp cover-related error was occurred.
132
Setting Network (SX80 II)
• Filter message:
• Unknown: it tells that an unknown error was occurred.
Make sure to install the SNMP manager program on your PC before using the SNMP agent function.
it tells that the air filter has reached its replacement timing.
Authentication and Encryption Protocols
SNMP V3 for the projector uses the DES-CBC for the authentication and encryption protocols.
6
Click [Projector info] and enter the projector name.
• You can input 1 to 63 alphanumeric characters.
• The factory default is [SX80 MarkII].
7
Click [Location], enter the projector location, and click the [OK] button.
• You can input up to 63 alphanumeric characters.
• The factory default is blank.
8
Click [Apply] when you have completed each menu.
Click the [OK] button when the following dialog box is displayed.
The network setting of the projector is now completed.
133
Setting Network (SX80 II)
If you want to test the error report transmission, click [Send test mail].
■Resetting the Network Setting
1
Click [Initialize] in the menu screen.
2
Click the [OK] button when the following dialog box is displayed.
If you want to restore to the factory setting from the projector, perform [Network setting initialization] from the menu.
134
Setting Network (SX80 II)
■Error Notification Message
It sends the following message when an error occurs in the projector.
Error list
Errors related to temperature
Errors related to the lamp
Errors related to the lamp cover
Errors related to the cooling fan
Errors related to the power supply
Other types of errors
Error name
Text
Error name
Text
Error name
Text
Error name
Text
Error name
Text
Error name
Text
Temperature abnormality
The temperature inside the projector is too high for some reason or the outside air temperature is higher than the specified one. If the problem is inside the projector, check whether the projector is installed and operated normally, turn off the projector to cool its inside, and retry projection. If the same warning occurs again, the projector may be defective. Contact your dealer.
Faulty lamp
The lamp has burnt out. Replace the lamp with a new one. If the same warning occurs again, the lamp drive circuit may be defective. Contact your dealer.
Faulty lamp cover
The lamp cover is open. Check whether the lamp cover is installed properly. If it is installed properly, the lamp cover detection switch may be defective. Contact your dealer.
Faulty cooling fan
The cooling fan or another component may be defective.
Contact your dealer.
Faulty power supply
The voltage of part of the power supply is abnormally high or any other problem has occurred in the power supply. Contact your dealer.
Unknown Error
Codes in hexadecimal numbers*
* Contact your Canon dealer.
135
Setting Network (SX80 II)
■Projector Control
1
Click the [Projector control] button on the network setting screen.
The projector control screen appears.
Controlled items:
[Power]:
[Input]:
Turn ON/OFF the projector (
Select an input signal ( P54
)
P49
, P68 )
[Aspect]: Select an aspect ratio (
P62
)
[Image mode]: Select an image mode ( P67 )
[Blank]:
[Mute]:
Blank out the image temporarily (
Mute the sound temporarily ( P71 )
P70 )
[Auto setup]: Perform the auto setup function (
P52
)
[Auto PC]:
Perform the auto PC function ( P57 )
• For [Input], [Aspect], and [Image mode], select an item and click the [Apply] button.
• Click the [Refresh] button to display the latest information.
• Click the [Back] button to return to the network setting screen.
• Do not use the [Back], [Forward], or [Refresh] button on your web browser when you control the projector. Using the web browser buttons may cause the projector to be malfunctioned. Be sure to use the buttons on the network setup window.
• Before terminating control of the projector, press the [Refresh] button to check whether the new setting is properly updated or not.
136
