6
Using Your TV and Remote
With Remote Buttons
P
OW
ER
VCR
D SS • C ABLE TV
V C R 2 • LD .
A U D I O
REW PLAY FF
REC
DISPLAY
STOP
CHAN
PAUSE
SKIP
L
V
POWER
Turns off the TV.
Turns off compatible VCRs.
Turns on a component after a component button is pressed.
AUDIO, VCR, VCR2•LD,
DSS•CABLE, TV
Sets the remote to control the component. VCR2 • LD can only be programmed for one component: either a VCR or a Laserdisc Player.
See Using the Remote with a VCR,
Cable Box, Laserdisc Player and Audio equipment on pages 8–15.
1
MUTE
4
2
5
CH AN PREV CH
3
6
7
INPUT
CLEAR
8
0
M
EN
U
•P
R
O
G
9
ANT A•B
RESET
TV
Turns on the TV.
Shows the displays on the screen.
Sets the remote to control the TV.
See Using the Remote with a VCR,
Cable Box, Laserdisc Player and Audio equipment on pages 8–15.
MOVE
REW (Rewind)
Rewinds a tape or laserdisc.
Searches backward while tape or laserdisc is playing.
PLAY
Plays tape or laserdisc.
FF (Fast Forward)
Fast forwards a tape or laserdisc.
Searches forward while tape or laserdisc is playing.
REC (Record)
Starts recording onto tape.
STOP
Stops tape or laserdisc.
PAUSE
Pauses tape or laserdisc.
DISPLAY
Shows displays on the screen.
Clears menus from the screen.
SKIP (Commercial Skip)
Allows you to scan other channels during commercials.
Each press adds 30 seconds. TV switches back to original channel when time runs out. Press
CLEAR to cancel SKIP.
CHAN 2 and 1
( Channel up and down)
Scans up and down through channels in the TV’s memory.
Moves through channels in VCR’s memory.
VOL
+ and
–
(Volume up and down)
Raises and lowers sound.
MUTE
Switches the TV sound on or off.
PREV CH (Previous Channel)
Changes back and forth between two channels.
Select a channel and then select another. Press PREV CH to switch between the two channels.
Using Your TV and Remote
With Remote Buttons
P OW
ER
VCR
D SS • C ABLE TV
V C R 2 • LD .
A U D I O
REW PLAY FF
REC
DISPLAY
L
STOP
CHAN
PAUSE
SKIP
1
MUTE
4
2
CH
AN PREV CH
3
5 6
7
INPUT
CLEAR
8
0
M
EN
U
•P
R
O
G
9
ANT A•B
RESET
MOVE
V
Number Buttons ( 0-9 )
Selects any channel number.
Two numbers must be pressed for each channel. Press 0 and 6 for channel 6. For three digit channels, press and hold 1 until 1-appears on the screen. Then press the other two numbers.
INPUT
Switches between the TV channels and Video 00.
ANT A•B (Antenna)
Used as TV/VCR button when remote is set to control the VCR.
CLEAR
Clears menus and displays from the screen.
Clears items from VCR timer programs and VCR’s clock.
MENU•PROG (Program)
Shows menus on the screen and moves from menu to menu.
Sets VCR clock and programs timer on VCR.
RESET
Returns the picture adjustments to the original settings.
MOVE
F and E (left and right)
Moves left and right on a menu line. See Menu Basics on page 5.
Changes a feature setting.
MOVE G and H (up and down)
Moves up and down menus. See
Menu Basics on page 5.
7
8
Using Your TV and Remote
With VCRs: Programming the Remote
Refer to the Connection Book or the VCR’s owners manual to hook up your VCRs.
The remote may need to be programmed for your VCR. This remote may not operate all models of brands listed below. Use the codes below or on the sheet packed in with your remote.
1.
Test the remote
POW
ER
VCR DSS•CABLE TV
VCR 2•LD
. AUDIO
REW PLAY FF
REC
DISPLAY
STOP PAUSE
CHAN SKIP
A .
Press VCR or VCR2 to turn the VCR on.
B .
Press the VCR buttons shown at the left. If your VCR does not work, program VCR or
VCR2 with a VCR code from the list below.
2.
Program the remote for your VCRs
1
MUTE
4
2
CHAN PREV CH
3
5 6
7
INPUT
CLEAR
8
0
ME
N
U
•PRO
G
9
ANT A•B
RESET
MOVE
A. Point the remote at the VCR and hold VCR.
B. Enter the code for your brand from the code list below.
C. Release VCR .
D. Press POWER . If nothing happens, try pressing VCR and then POWER .
E. Repeat A–D with another code if the first one does not work or if a second VCR is connected.
VCR Codes
Aiwa .................................................15
Akai ........................................03,22,23
Audio Dynamics........................14,16
Broksonic .........................................10
Canon ...............................................08
Capehart...........................................01
Citizen ..............................................09
Craig ............................................07,12
Curtis Mathes ........................00,08,15
Daewoo ............................................13
dbx ...............................................14,16
Dimensia ..........................................00
Dynatech ..........................................15
Emerson ...09,10,13,15,20,23,24,34,41
Fisher ............................02,12,18,19,43
Funai.................................................15
GE .................................00,07,08,32,37
Goldstar.......................................09,14
Harman Kardon..............................14
Hitachi ...............................05,15,35,36
Instant Replay .................................08
JCL ....................................................08
JCPenney.......02,05,07,08,14,16,30,35
JVC .....................................02,14,16,30
Kenwood...........................02,14,16,30
Lloyd ................................................15
Magnavox ...................................08,29
Marantz ...................02,08,14,16,29,30
Marta ................................................09
MEI ...................................................08
Memorex ...........................08,09,12,15
MGA ............................................04,27
Minolta ........................................05,35
Mitsubishi ....................04,05,27,35,40
Montgomery Ward.........................06
MTC.............................................07,15
Multitech...........................07,15,31,32
NEC ...................................02,14,16,30
Panasonic .........................................08
Pentax ..........................................05,35
Philco ...........................................08,29
Philips..........................................08,29
Pioneer ...................................05,16,33
ProScan.............................................00
Quartz...............................................02
Quasar ..............................................08
RCA ....................00,05,07,08,28,35,37
Realistic .........02,06,08,09,12,15,19,43
Samsung.......................07,13,22,32,42
Sansui ...............................................16
Sanyo..........................................02,12
Scott.......................................04,13,41
Sears .............02,05,09,12,18,19,35,43
Sharp .....................................06,24,39
Shintom ................................17,26,31
Sony.......................................17,26,38
Sylvania ................................08,15,29
Symphonic ................................02,15
Tashiko ...........................................09
Tatung.............................................30
Teac ............................................15,30
Technics ..........................................08
Teknika ............................08,09,15,21
Toshiba .................................05,13,19
Totevision..................................07,09
Unitech ...........................................07
Vector Research........................14,16
Victor ..............................................16
Video Concepts ........................14,16
Videosonic......................................07
Wards..................................................
............05,06,07,08,12,13,15,25,31,35
Yamaha............................02,14,16,30
Zenith.........................................11,17
Using Your TV and Remote
With VCRs: Setting the VCR1 Channel
The VCR 1 Channel works with VCR on the remote. If the VCR 1 Channel is set, pressing VCR selects the channel to see the VCR picture. The VCR 1
Channel setting depends on which diagram you have used from the
Connection Guide. If you want to turn this feature off, set the VCR 1
Channel to Disable. Refer to the chart below for your setting.
1.
Select the Setup Menu
13
A. Press TV to set the remote to control the TV.
B. Press MENU•PROG to select the
Setup menu. This menu is white.
Controls Alarm Adjust Setup
English Français Español
Autoprogram
Label 13 clear
Channel Memory: 13 Stored
Cable/Air: Cable
2.
Highlight VCR1 Channel
Controls Alarm Adjust Setup
English Français Español
Autoprogram
Label 13 clear
Channel Memory: 13 Stored
Cable/Air: Cable
VCR 1 Channel: 03
13 A. Press MOVE
H
( down) to highlight the VCR 1 Channel.
B. Press E to highlight the channel.
3.
Enter channel number
Controls Alarm Adjust Setup
English Français Español
Autoprogram
Label 13 clear
Channel Memory: 13 Stored
Cable/Air: Cable
VCR 1 Channel: 00
13
A. Enter channel 00, 03, or 04.
Choose your setting from the chart below. Press CHANNEL down until “Disabled” is displayed to turn the feature off.
Diagram used from the
Connection Guide:
1B, 1C, 2B, 2C, 3B, 3C, 4C, 5C
4B, 5B
Set VCR1 Channel to:
00
3 or 4 (same as 3/4 switch)
9
10
Using Your TV and Remote
With VCRs: Basic Operation
If the remote operates your VCR, this page and the next will show you how to use it for basic functions. See page 7 for more details on buttons used with your VCR.
Turn on the VCR
Turn off the VCR
P OW
ER
VCR
D S S • C ABLE TV
V C R 2 • LD .
A U D I O
REW PLAY FF
REC
DISPLAY
STOP
CHAN
PAUSE
SKIP
L
V
1
MUTE
4
2
CH
AN PREV CH
3
5 6
7
INPUT
CLEAR
8
0
M
EN
U
•P
R
O
G
9
ANT A•B
RESET
MOVE
A. Press channel 00 on the TV to see what the VCR is doing.
B. Press VCR or VCR2 to set the remote to control the VCR.
C. Press POWER to turn on the
VCR if it did not turn on when you pressed VCR or VCR2 .
A. Press VCR or VCR2 to set the remote to control the VCR.
B. Press POWER .
Using Your TV and Remote
With VCRs: Basic Operation
If the remote operates your VCR, this page and page 10 will show you how to use it for basic functions. See page 7 for more details on buttons used with your VCR.
Record one TV program and watch another
Watch a tape in your VCR
P
OW
ER
VCR
D SS • C ABLE
TV
V C R 2 • LD .
A U D I O
REW PLAY FF
REC
DISPLAY
STOP
CHAN
PAUSE
SKIP
L
V
1
MUTE
2
CH
AN PREV CH
3
4 5 6
7
INPUT
CLEAR
8
0
M
EN
U
•P
R
O
G
9
ANT A•B
RESET
MOVE
A. Press VCR or VCR2 to set the remote to control the VCR.
B. Tune the VCR to the channel you want to record using
CHANNEL up and down or pressing two number buttons.
C. Press RECORD to start recording.
D. Press TV/VCR on the VCR.
E. Press TV to set the remote to control the TV.
F. Press CHANNEL up or down to change channels on the TV.
G. To see the channel you are recording, tune the TV back to channel 00.
A. Turn on VCR.
B. Insert a tape in the VCR.
C. Press PLAY to start the tape playing.
D. Press STOP when you are finished.
E. Press REW to rewind the tape.
11
Using Your TV and Remote
With a Cable Box: Programming and Basic Operation
Refer to the Connection Book or contact your cable company to hook up your cable
box. If you have a cable box with its own remote, then you may also be able to use the TV’s remote with your cable box. This remote may not operate all models of brands listed below. Use the codes below or on the sheet packed in with your remote.
Program the remote for your cable box
POW
ER
VCR
DSS • CABLE
TV
VCR 2•LD . AUD IO
REW
REC
DISPLAY
PLAY FF
STOP PAUSE
CHAN SKIP
A. Point the remote at the cable box and hold CABLE .
B. Enter the code numbers for your brand from the list below.
C. Release CABLE .
D. Press POWER to turn it on. If nothing happens, try pressing
CABLE and then POWER .
E. Repeat A-D with another code if the first one does not work.
Basic Operation:
Turn on the Cable Box
Turn off the Cable Box
1
MUTE
2
CHAN PREV CH
3
4 5 6
7
INPUT
CLEAR
8
0
M
EN
U
•P
R
O
G
9
ANT A•B
RESET
MOVE
A. Tune TV to channel 02, 03, 04,
05, or 06--the cable box channel.
B. Point remote at the cable box and press CABLE .
C. Press POWER to turn it on.
D. Press CHANNE L up or down to change channels on the cable box.
A. Press CABLE .
B. Press POWER to turn it off.
12
Cable Box Codes
ABC ..............................................22,46
Anvision.......................................07,08
Cablestar ......................................07,08
Eagle ..................................................08
Eastern International.......................02
General Instrument .............................
....................04,05,15,23,24,25,30,36,46
Hamlin ...............................12,13,34,48
Hitachi.....................................37,43,46
Jerrold....................................................
..........04,05,15,23,24,25,30,36,45,46,47
MACOM ......................................37,43
Magnavox .............................................
..........07,08,19,21,26,28,29,32,33,40,41
NSC ...................................................09
Oak ..........................................01,16,38
Oak Sigma ........................................16
Panasonic................................03,27,39
Philips ...................................................
..........07,08,19,21,26,28,29,32,33,40,41
Pioneer ....................................18,20,44
Randtek........................................07,08
RCA ..............................................00,27
Regal.............................................12,13
Regency........................................02,33
Samsung ...........................................44
Scientific Atlanta....................03,22,35
Signature...........................................46
Sprucer ..............................................27
Starcom .............................................46
Sylvania.............................................11
Teknika .............................................06
Texscan.........................................10,11
Tocom.................................17,21,49,50
Unika .......................................31,32,41
Viewstar................................................
..........07,08,19,21,26,28,29,32,33,40,41
Warner Amex...................................44
Zenith ...........................................14,42
Using Your TV and Remote
With a Cable Box: Setting the Cable Channel
The Cable Channel works with CABLE on the remote. If the Cable
Channel is set, pressing CABLE selects the channel to see cable channels.
The Cable Channel setting depends on which channel your cable box must be on to see cable channels. The channels usually used are 02, 03,
04, 05 or 06. Consult your cable company for more information.
1.
Select the Setup menu
Controls Alarm Adjust Setup
English Français Español
Autoprogram
Label 13 clear
Channel Memory: 13 Stored
Cable/Air: Cable
VCR 1 Channel: 00
Cable Channel: 02
13 A. Press TV to set the remote to control the TV.
B. Press MENU•PROG to select the
Setup menu. This menu is white.
2.
Highlight Cable Channel
Controls Alarm Adjust Setup
English Français Español
Autoprogram
Label 13 clear
Channel Memory: 13 Stored
Cable/Air: Cable
VCR 1 Channel: 00
Cable Channel: 02
13
A. Press MOVE
H
( down) to move down the menu until Cable
Channel is highlighted.
B. Press
E to underline the channel.
3.
Enter channel number
13
Controls Alarm Adjust Setup
English Français Español
Autoprogram
Label 13 clear
Channel Memory: 13 Stored
Cable/Air: Cable
VCR 1 Channel: 00
Cable Channel: 03
A. Enter the number for your cable box, either 02,03,04,05, or 06.
Press CHANNEL down until
“Disabled” is displayed to turn this feature off.
13
Using Your TV and Remote
With a Laserdisc Player: Programming and Basic Operation
Refer to your Laserdisc Player owner’s manual to hook up your Laserdisc Player.
The remote may need to be programmed for your laserdisc player. This remote may not operate all models of brands listed below. Use the codes below or on the sheet packed in with your remote.
Program the remote for your Laserdisc Player
Basic Operation
POW
ER
VCR DSS•CABLE TV
VCR 2•LD
. AUDIO
REW PLAY FF
REC
DISPLAY
S TOP
CHAN SKIP
L
V
1
MUTE
4
2
5
CHAN PREV CH
3
6
7
INPUT
CLEAR
8
0
M
EN
U
•P
R
O
G
9
ANT A•B
RESET
MOVE
A. Point the remote at the laserdisc player and hold
LD .
D. Press POWER . If nothing happens, try pressing LD and then POWER .
LD .
B. Enter the code for your brand from the code list below.
C. Release
A. Tune TV to channel 00, 03, or 04.
B. Point the remote at the laserdisc player and press LD .
C. Press POWER to turn it on.
D. Use the buttons on the remote that relate to laserdisc player functions. Not all buttons highlighted may work with your laserdisc player.
E. Press POWER to turn it off.
14
Laserdisc Player Codes
Pioneer ........................33
ProScan .......................33
RCA.............................33
Using Your TV and Remote
With Audio Equipment: Programming and Basic Operation
Refer to the Connection Book or your Audio equipment owner’s manual to hook
up your audio equipment. Your remote controls only RCA audio equipment such as a radio, CD player, tape player, turntable, or amplifier. The remote may need to be programmed for your equipment. This remote may not operate all models of brands listed below. Use the codes below or on the sheet packed in with your remote.
Program the remote for audio equipment
Basic Operation
POW
ER
VCR DSS•CABLE TV
VCR 2•LD .
AUDIO
REW
REC
DISPLAY
PLAY
STOP
CHAN
FF
PAUSE
SKIP
L
V
MUTE
1
4
2
5
CHAN PREV CH
3
6
7
INPUT
CLEAR
8
0
M
EN
U
•P
R
O
G
9
ANT A•B
RESET
MOVE
A. Point the remote at the audio equipment and hold AUDIO .
B. Enter the code from the code list.
C. Release AUDIO .
D. Press POWER to turn it on. If nothing happens, try pressing
AUDIO and then POWER .
E. Repeat A–D with another code if the first one does not work.
A.
Point the remote at the audio equipment and press AUDIO .
B. Press POWER to turn it on.
C. Use the buttons on the remote that relate to audio functions.
Not all buttons highlighted may work with your equipment.
D. Turn the audio equipment off using the audio component’s power off button.
Audio Codes
RCA/ Dimensia
AM/FM...........................03
CD ....................................07
Tape .................................06
Phono ..............................05
Aux ..................................04
15
