Parts Name and Functions. NEC X462UN-TMX9P, 5 x 5 - X461UN Display Set, X462UN-TMX4P, 4 x 4 - X461UN Display Set, 10 x 10 - X461UN Display Set, 2 x 2 - X461UN Display Set, X462UNV, 3 x 3 - X461UN Display Set, MultiSync® X461UNV

Add to My manuals
42 Pages

advertisement

Parts Name and Functions. NEC X462UN-TMX9P, 5 x 5 - X461UN Display Set, X462UN-TMX4P, 4 x 4 - X461UN Display Set, 10 x 10 - X461UN Display Set, 2 x 2 - X461UN Display Set, X462UNV, 3 x 3 - X461UN Display Set, MultiSync® X461UNV | Manualzz

Parts Name and Functions

Control Panel

POWER button

Switches the power on/off. See also page 16.

MUTE button

Switches the audio mute ON/OFF.

INPUT button

Acts as SET button within OSD menu. (Toggle switches between [DVI], [DPORT], [VGA], [RGB/HV], [HDMI],

[DVD/HD1], [DVD/HD2], [SCART], [VIDEO1], [VIDEO2],

[S-VIDEO] or [TV]*). These are available input only, shown as their factory preset name.

PLUS button

Acts as (+) button to increase the adjustment with OSD menu.

Increases the audio output level when the OSD menu is turned off.

MINUS button

Acts as (-) button to decrease the adjustment with OSD menu.

Decreases the audio output level when the OSD menu is turned off.

UP button

Activates the OSD menu when the OSD menu is turned-off.

Acts as button to move the highlighted area up to select adjustment items within OSD menu.

DOWN button

Activates the OSD menu when the OSD menu is turned-off.

Acts as button to move the highlighted area down to select adjustment items within OSD menu.

EXIT button

Activates the OSD menu when the OSD menu is turned-off.

Acts as EXIT button within the OSD to move to previous menu.

Remote control sensor and Power Indicator

Receives the signal from the remote control (when using the wireless remote control). See also page 11.

Glows green when the LCD monitor is in active mode*.

Glows red when the LCD is in POWER OFF (ECO standby) mode. Glows amber when the LCD is in POWER OFF

(standby) mode. Blinks amber when the monitor is in Power

Save Mode. Green and Amber blink alternately while in

Power Standby mode with the “SCHEDULE SETTINGS” function enabled. When a component failure is detected within the monitor, the indicator will blink red.

* If “OFF” is selected in “POWER INDICATOR” (see page 23),

LED will not light when the LCD monitor is in active mode.

Control Key Lock Mode

This control completely locks out access to all Control Key functions. To activate the control key lock function, press both

and and hold down simultaneously for more than

3 seconds. To resume user mode, press both and and hold simultaneously for more than 3 seconds.

*: The product you purchased may not have this feature.

English-7

Terminal Panel

In Out Option control unit

In Out

R, Cr/Pr

(OUT)

G, Y, VIDEO

(OUT)

B, Cb/Pb

(OUT)

H

(OUT)

V

(OUT) Y Cb/Pb

L/R

(IN1)

L

(IN2)

L

(IN3)

L (OUT)

R (OUT)

R, Cr/Pr

(IN)

G, Y, VIDEO

(IN)

B, Cb/Pb

(IN)

H

(IN)

V

(IN)

Cr/Pr R

(IN2)

R

(IN3)

Main Power Switch

On/Off switch to turn main power ON/OFF.

AC IN connector

Connects with the supplied power cord.

DISPLAYPORT connector

To input DisplayPort signals.

HDMI connector

To input digital HDMI signals.

DVI IN (DVI-D)

To input digital RGB signals from a computer or HDTV device having a digital RGB output.

* This connector does not support analog input.

VGA IN (mini D-Sub 15 pin)

To input analog RGB signals from a personal computer or from other RGB equipment.

RGB/HV IN [R, G, B, H, V] (BNC)

To input analog RGB signals or signals from other RGB equipment.

This is also to connect equipment such as a DVD player,

HDTV device and Set-Top-Box. A Sync-on-Green signal can be connected to the G connector.

This input can be used with an RGB, DVD/HD or Video source. Please select signal type in TERMINAL SETTING.

RGB/HV

DVD/HD2

VIDEO2

R

R

Pr

G

G

Y

VIDEO

B

B

Pb

H

H

V

V

RGB/HV OUT (BNC)

To output the signal from the RGB/HV IN connector or

VGA IN connector which is on screen to an input on a separate device. If both signals are not on screen, outputs the signal from RGB/HV IN connector.

VIDEO IN connector (BNC and RCA)

To input a composite video signal. BNC and RCA connectors are not available at the same time (Use only one input).

VIDEO OUT connector (BNC)

To output the composite video signal from the VIDEO IN connector.

DVD/HD connector (RCA)

Connecting equipment such as a DVD player, HDTV device, or Set-Top-Box.

S-VIDEO IN connector (Mini DIN 4 pin)

To input the S-video (Y/C separate signal).

AUDIO IN 1, 2, 3

To input audio signal from external equipment such as a computer, VCR or DVD player.

AUDIO OUT

To output the audio signal from the AUDIO IN 1, 2, 3,

DPORT, HDMI, and TV jack to an external device (stereo receiver, amplifier, etc.).

EXTERNAL CONTROL (D-Sub 9 pin)

IN connector: Connect RS-232C input from external equipment such as a PC in order to control RS-232C functions.

OUT connector: Connect RS-232C output. To connect multiple MultiSync monitors via RS-232C daisy Chain.

English-8

LAN port (RJ-45)

LAN connection. See page 31.

REMOTE IN/OUT

Use the optional wired remote control by connecting it to your monitor.

NOTE: When you use Remote IN/OUT, IR CONTROL in

OSD menu should be NORMAL.

Kensington Lock

For security and theft prevention.

Remote control sensor

Receives the signal from the remote control.

AMBIENT LIGHT SENSOR

Detects the level of ambient light, allowing the monitor to make automatic adjustments to brightness settings, resulting in a more comfortable viewing experience.

Do not cover this sensor. See page 18.

Option board slot

Slot for board accessories. Please contact your supplier for detailed information.

English-9

Wireless Remote Control (Optional)

POWER button

Switches the power on/standby.

INPUT button

Selects input signal.

DVI: DVI

DISPLAYPORT: DPORT

VGA: VGA

RGB/HV: RGB/HV

HDMI: HDMI

DVD/HD: DVD/HD1, DVD/HD2, SCART

VIDEO: VIDEO1, VIDEO2

S-VIDEO: S-VIDEO

OPTION: Depends on your connection

PICTURE MODE button

Selects picture mode, [HIGHBRIGHT], [STANDARD],

[sRGB], [CINEMA], [AMBIENT1], [AMBIENT2]. See page 18.

HIGHBRIGHT: for moving images such as DVD.

STANDARD: for images.

sRGB: for text based images.

CINEMA: for movies.

AMBIENT1 and AMBIENT2: activate auto dimming function. See page 18.

ASPECT button

Selects picture aspect, [FULL], [NORMAL], [WIDE] and

[ZOOM]. See page 17.

SOUND button (not available)

KEYPAD

Press buttons to set and change passwords, change channel and set REMOTE ID.

ENT button*

DISPLAY button

Turns on/off the information OSD. See page 17.

MENU button

Turns on/off the menu mode.

AUTO SETUP button

Enters auto setup menu. See page 20.

EXIT button

Returns to previous menu within OSD menu.

UP/DOWN button

Acts as button to move the highlighted area up or down to select adjustment items within OSD menu.

Small screen which adjusted “PIP” mode moves up or down.

MINUS/PLUS (-/+) button

Increases or decreases the adjustment level within OSD menu settings.

Small screen which adjusted “PIP” mode moves left or right.

SET button

Makes selection.

VOLUME UP/DOWN button

Increases or decreases audio output level.

CH UP/DOWN button*

GUIDE button*

MUTE button

Turns on/off mute function.

STILL button

ON/OFF button: Activates/deactivates still picture mode.

STILL CAPTURE button: Captures still picture.

PIP (Picture In Picture) button

ON/OFF button: Toggle switches between PIP, POP, sideby-side (aspect) and side-by-side (full). See page 22.

INPUT button: Selects the “picture in picture” input signal.

CHANGE button: Replaces to the main picture and sub picture.

Sub picture

DVI

DPORT

VGA

RGB/HV

HDMI

DVD/HD1

DVD/HD2

SCART

VIDEO1

VIDEO2

S-VIDEO

DVI DPORT VGA RGB/HV HDMI DVD/HD1 DVD/HD2 SCART VIDEO1 VIDEO2 S-VIDEO

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

English-10

REMOTE ID button

Activates REMOTE ID function.

MTS button*

AUDIO INPUT button

Selects audio input source [IN1], [IN2], [IN3], [DPORT],

[HDMI], [TV]* 1 , [OPTION]* 1 .

button

Activates closed captioning.

Note: VIDEO1, VIDEO2, S-VIDEO inputs only.

*: This button’s action depends on which option board you use.

Refer to the option board’s manual for further information.

*1: The product you purchased may not have this feature.

Operating Range for the Option

Remote Control

Point the top of the remote control toward the sensor unit’s remote control sensor in optional control kit during button operation.

Use the remote control within a distance of about 7 m (23 ft.) from remote control sensor or at a horizontal and vertical angle of within 30° within a distance of about 3.5 m (10 ft.).

Caution: Important, the remote control system may not function when direct sunlight or strong illumination strikes the remote control sensor or when there is an object in the path.

Handling the remote control

• Do not subject to strong shock.

• Do not allow water or other liquid to splash the remote control. If the remote control gets wet, wipe it dry immediately.

• Avoid exposure to heat and steam.

• Other than to install the batteries, do not open the remote control.

English-11

advertisement

Related manuals