Basic Operation. NEC X462UN-TMX9P, 5 x 5 - X461UN Display Set, X462UN-TMX4P, 4 x 4 - X461UN Display Set, 10 x 10 - X461UN Display Set, 2 x 2 - X461UN Display Set, X462UNV, 3 x 3 - X461UN Display Set, MultiSync® X461UNV

Add to My manuals
42 Pages

advertisement

Basic Operation. NEC X462UN-TMX9P, 5 x 5 - X461UN Display Set, X462UN-TMX4P, 4 x 4 - X461UN Display Set, 10 x 10 - X461UN Display Set, 2 x 2 - X461UN Display Set, X462UNV, 3 x 3 - X461UN Display Set, MultiSync® X461UNV | Manualzz

Basic Operation

Power ON and OFF Modes

The LCD monitor power indicator will turn green while powered on and will turn red or amber while powered off.

NOTE: The Main Power Switch must be in the ON position in order to power up the monitor using the remote control or the

Power Button on the front of the LCD.

OFF

ON

Main Power Switch

Power Button

Using the optional remote control

English-16

Power Indicator

Mode

Power ON

Power OFF (Eco Standby)* 1

Power consumption under 0.5W* 3

Power OFF (Standby)

Power consumption under 1W* 3, * 4

Power Save

Power consumption under 2W* 3, * 5

Green*

Red

Amber

Status Indicator Light

2

Amber Blinking

Power Standby when

“SCHEDULE SETTINGS” enabled

Diagnosis (Detecting failure)

Green and Amber blink alternately

Red Blinking

(See Troubleshooting page 36)

*1 When in Eco Standby Mode DDC/CI control does not function.

*2 If “OFF” is selected in POWER INDICATOR (page 23), the LED will not light when the LCD monitor is in active mode.

*3 “RS-232C” is selected in EXTERNAL CONTROL.

*4 DDC/CI should be disabled.

*5 No DisplayPort connection.

Using Power Management

The LCD monitor follows the VESA approved DPM Power

Management function.

The power management function is an energy saving function that automatically reduces the power consumption of the display when the keyboard or the mouse has not been used for a fixed period.

The power management feature on your new display has been set to the “ON” mode. This allows your display to enter a Power Saving Mode when no signal is applied. This could potentially increase the life and decrease the power consumption of the display.

NOTE: Depending on the PC and video card used, this function may not operate.

Selecting a video source

To view a video source:

Use the input button to set [VIDEO1], [VIDEO2], [S-VIDEO].

Use the COLOR SYSTEM menu to set [AUTO], [NTSC],

[PAL], [SECAM], [PAL60], [4.43NTSC], according to your video format.

Picture Aspect

DVI, VGA, RGB/HV, DPORT

FULL ZOOM NORMAL

HDMI, DVD/HD1, DVD/HD2, SCART, VIDEO1, VIDEO2, S-VIDEO, TV*

FULL WIDE ZOOM NORMAL

Aspect ratio of image

Unchanged view* 6 Recommended selection for picture aspect* 6

NORMAL

NORMAL: Displays the aspect ratio the same as it is sent from the source.

FULL: Fills entire screen.

WIDE: Expands a 16:9 letter box signal to fill entire screen.

ZOOM (DYNAMIC): Expands a 4:3 pictures to fill the entire screen with non-linearity. Some of the outside image area will be cut off due to expansion.

ZOOM

The image can be expanded beyond the active display area.

The image which is outside of active display area is not shown.

ZOOM

ZOOM

Information OSD

The Information OSD provides information such as:

Monitor ID, Input Source, Picture Size, etc. Press the

DISPLAY button on the remote to bring up the Information

OSD.

ID number assigned to current monitor* 7

ID number assigned monitor to be controlled via RS-232C* 8

Input Name

Audio input mode

Picture aspect

Input Signal Information

Sub picture information

*7: “IR CONTROL” should be set “Primary” or “Secondary”.

*8: “IR CONTROL” should be set “Primary”.

*: The product you purchased may not have this feature.

4:3

ZOOM

(DYNAMIC)

FULL

Squeeze

WIDE

Letterbox

* 6 Grey areas indicate unused portions of the screen.

English-17

Picture Mode

DVI, VGA, RGB/HV, DPORT

STANDARD sRGB AMBIENT1 AMBIENT2 HIGHBRIGHT

HDMI, DVD/HD1, DVD/HD2, SCART, VIDEO1, VIDEO2, S-VIDEO, TV*

STANDARD CINEMA AMBIENT1 AMBIENT2 HIGHBRIGHT

AMBIENT Mode

The brightness of the LCD screen can be set to increase or decrease depending on the amount of ambient light within the room. If the room is bright, the monitor becomes correspondingly bright. If the room is dim, then the monitor will dim accordingly. The purpose of this function is to make the viewing experience more comfortable to the eye in a variety of lighting conditions.

NOTE: When picture mode is set to AMBIENT1 or AMBIENT2, BRIGHTNESS, AUTO BRIGHTNESS and BRIGHTNESS in

SCREEN SAVER function are disabled.

Do not cover Ambient light sensor when you use AMBIENT1 or AMBIENT2 in PICTURE MODE.

AMBIENT parameter setting

PICTURE MODE in OSD, select AMBIENT1 or AMBIENT2 and set IN BRIGHT and IN DARK in each mode.

IN BRIGHT: This is the brightness level that the monitor will go up to when the ambient light level is highest.

IN DARK: This is the level of brightness that the monitor will go down to when the ambient light level is low.

When the AMBIENT function is enabled the Brightness level of the screen changes automatically according to the lighting conditions of the room (Figure 1).

Factory Setting

BRIGHTNESS range

BRIGHTNESS level set for the monitor to use when ambient lighting level is low.

BRIGHTNESS level set for the monitor to use when ambient lighting level is high.

IN DARK IN BRIGHT dark room bright condition bright

Screen Brightness value by AMBIENT1 mode

Screen Brightness value by AMBIENT2 mode

Figure 1

IN DARK: BRIGHTNESS level set for the monitor to use when ambient lighting level is low.

IN BRIGHT: BRIGHTNESS level set for the monitor to use when ambient lighting level is high.

*: The product you purchased may not have this feature.

English-18

advertisement

Related manuals