Basic Operation. NEC V652-TM

Add to My manuals
45 Pages

advertisement

Basic Operation. NEC V652-TM | Manualzz

Basic Operation

Power ON and OFF Modes

The LCD monitor power indicator will turn green while powered on and will turn red or amber while powered off.

NOTE: The Main Power Switch must be in the ON position in order to power up the monitor using the remote control or the

Power Button on the front of the LCD.

OFF

ON

Main Power Switch

Power Button

Using the remote control

POWER ON Button

English-18

Power Indicator

Mode Status Indicator Light

Power ON Green* 1

Power OFF

Power consumption under 0.5 W

Power Save

Power consumption under 1 W* 2

Red

Amber

Power Standby when “SCHEDULE

SETTINGS” enabled

Diagnosis (Detecting failure)

Green and Amber blink alternately

Red Blinking

(See Troubleshooting page 39)

*1 If “OFF” is selected in POWER INDICATOR (page 25), the LED will not light when the

LCD monitor is in active mode.

*2 Without any option, with factory settings, VGA input only.

Using Power Management

The LCD monitor follows the VESA approved DPM Display

Power Management function.

The power management function is an energy saving function that automatically reduces the power consumption of the display when the keyboard or the mouse has not been used for a fi xed period.

The power management feature on your new display has been set to the “ON” mode. This allows your display to enter a Power Saving Mode when no signal is applied. This could potentially increase the life and decrease the power consumption of the display.

NOTE: Depending on the PC and video card used, this function may not operate.

NOTE: It takes about 10 minutes for the monitor to go into power management mode when using DVD/HD,

SCART, VIDEO1, VIDEO2 and S-VIDEO.

Selecting a video source

To view a video source:

Use the input button to set [VIDEO1], [VIDEO2], [S-VIDEO].

Use the COLOR SYSTEM menu to set [AUTO], [NTSC],

[PAL], [SECAM], [PAL60], [4.43NTSC], according to your video format.

Picture Aspect

DVI, VGA, RGB/HV, DPORT

FULL 1:1 ZOOM NORMAL

HDMI, DVD/HD, SCART, VIDEO1, VIDEO2, S-VIDEO

FULL WIDE DYNAMIC 1:1 ZOOM NORMAL

Aspect ratio of image

Unchanged view* 3

Recommended selection for picture aspect* 3

NORMAL

4:3

Squeeze

Letterbox

DYNAMIC

FULL

WIDE

* 3 Grey areas indicate unused portions of the screen.

NORMAL: Displays the aspect ratio the same as it is sent from the source.

FULL: Fills entire screen.

WIDE: Expands a 16:9 letter box signal to fi ll entire screen.

DYNAMIC: Expands a 4:3 pictures to fi ll the entire screen with non-linearity. Some of the outside image area will be cut off due to expansion.

1:1: Displays the image in a 1 by 1 pixel format.

ZOOM

The image can be expanded beyond the active display area.

The image which is outside of active display area is not shown.

ZOOM

ZOOM

English-19

Information OSD

The Information OSD provides information such as: Monitor ID, Input Source, Picture Size, etc.

Press the DISPLAY button on the remote to bring up the Information OSD.

ID number assigned to current monitor* 1

ID number assigned monitor to be controlled via RS-232C* 2

Input Name

Audio input mode

Picture aspect

Input Signal Information

Sub picture information

*1: “IR CONTROL” should be set “Primary” or “Secondary”.

*2: “IR CONTROL” should be set “Primary”.

Picture Mode

DVI, VGA, RGB/HV, DPORT

STANDARD sRGB AMBIENT1 AMBIENT2 HIGHBRIGHT

HDMI, DVD/HD, SCART, VIDEO1, VIDEO2, S-VIDEO

STANDARD CINEMA AMBIENT1 AMBIENT2 HIGHBRIGHT

AMBIENT Mode

The backlight of the LCD screen can be set to increase or decrease depending on the amount of ambient light within the room.

If the room is bright, the monitor becomes correspondingly bright. If the room is dim, then the monitor will dim accordingly. The purpose of this function is to make the viewing experience more comfortable to the eye in a variety of lighting conditions.

NOTE: When picture mode is set to AMBIENT1 or AMBIENT2, BACKLIGHT, AUTO BRIGHTNESS and BACKLIGHT in

SCREEN SAVER function are disabled.

Do not cover Ambient light sensor when you use AMBIENT1 or AMBIENT2 in PICTURE MODE.

AMBIENT parameter setting

PICTURE MODE in OSD, select AMBIENT1 or AMBIENT2 and set IN BRIGHT and IN DARK in each mode.

IN BRIGHT: This is the backlight level that the monitor will go up to when the ambient light level is highest.

IN DARK: This is the level of backlight that the monitor will go down to when the ambient light level is low.

When the AMBIENT function is enabled the Backlight level of the screen changes automatically according to the lighting conditions of the room (Figure 1).

Factory Setting

BACKLIGHT range

BACKLIGHT level set for the monitor to use when ambient lighting level is low.

BACKLIGHT level set for the monitor to use when ambient lighting level is high.

IN DARK IN BRIGHT room bright condition dark bright

Screen Backlight value by AMBIENT1 mode

Screen Backlight value by AMBIENT2 mode

Figure 1

IN DARK: BACKLIGHT level set for the monitor to use when ambient lighting level is low.

IN BRIGHT: BACKLIGHT level set for the monitor to use when ambient lighting level is high.

English-20

advertisement

Related manuals