Step 2: Unpacking the Printer. HP 8500 N, 8500 DN, 8500, Color LaserJet 8500 Printer series

Add to my manuals
56 Pages

advertisement

Step 2: Unpacking the Printer. HP 8500 N, 8500 DN, 8500, Color LaserJet 8500 Printer series | Manualzz

Figure 2

Step 2: Unpacking the Printer

N o t e

The following items are included with the printer:

A

B

C

D

F

G

H

E

Toner cartridges: black, cyan, magenta, and yellow

Power cord

Software on CD-ROM

Manuals: getting started guide (this guide) and quick reference guide; the online user’s guide is on a CD-ROM

Printer—shown with standard printer stand; if ordered, an optional tray

4 replaces the printer stand

Imaging drum

Control panel overlay (if applicable)

Left (face-up) output bin

If an optional 2,000-sheet input tray (tray 4) was ordered, a power pack

(containing power connections for the printer and tray 4), a preinstalled interface cable (connecting tray 4 to the printer), and five stabilizing legs are also included.

4 Step 2: Unpacking the Printer

EN

To unpack the printer

1

2

3

4

Remove all external packing tape from the printer.

Open the lower left door and push down the green lever on the right side of the fuser. Then, remove the orange shipping notice from the fuser.

Open the upper right door and remove the packing tape at the left side of the opening.

Open the front door.

EN

Step 2: Unpacking the Printer 5

5

6

7

8

9

Remove the packing material from the lower (green) lever.

Press the white button on the lower

(green) lever and swing the lever to the right.

Remove the packing cardboard from inside the printer and then swing the lower (green) lever back to the left, making sure the lever clicks into place.

Firmly grip the handle in the center of tray 2, squeeze the release lever, and pull the tray out until it stops. Then remove the orange packing spacers from inside the tray and close the tray.

Repeat step 8 to remove the orange packing spacers from tray 3.

If the printer came with an optional tray 4, continue with step 10. If the printer came with a stand, proceed to step 18.

6 Step 2: Unpacking the Printer

EN

N o t e

Follow steps 10-13 to attach the five stabilizing legs to the bottom of tray 4. If the five stabilizing legs (which are in addition to the four locking wheels) are already attached, proceed to step 14.

10

11

12

13

Locate the five stabilizing legs that came with the printer.

Locate the five guides for the stabilizing legs on the bottom of tray

4—two guides at the front edge, one on the right edge, and two on the back edge.

Insert a stabilizing leg into one of the guides and push the leg into the guide until it stops.

Repeat step 12 above to attach the other four stabilizing legs.

EN

Step 2: Unpacking the Printer 7

14

15

16

17

Remove the packing tape from tray 4.

Open the media transfer door and remove the orange packing spacers.

Firmly grip the handle in the center of tray 4, squeeze the release lever, and pull the tray out until it stops.

Remove the two orange packing clips from inside tray 4 by squeezing the sides of the clips and pulling them out.

C a u t i o n

Leaving the orange clips in tray 4 can damage the tray.

18

19

Close all doors and input trays.

Remove the protective film from the printer control panel display.

By completing steps 1 through 19 above, all tape and spacers should be removed and unpacking of the printer should be complete.

8 Step 2: Unpacking the Printer

EN

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement