Step 6: Installing the Consumables. HP 8500 N, 8500 DN, 8500, Color LaserJet 8500 Printer series

Add to My manuals
56 Pages

advertisement

Step 6: Installing the Consumables. HP 8500 N, 8500 DN, 8500, Color LaserJet 8500 Printer series | Manualzz

Figure 3

Step 6: Installing the Consumables

Figure 4

The following parts (consumables) are included with the printer:

A

B

C

Imaging Drum

Black Toner Cartridge

Color Toner Cartridges: yellow, magenta, and cyan

Install the consumables in the printer in this order:

A

B

C

Imaging Drum

Black Toner Cartridge

Color Toner Cartridges (behind the clear door are three slots, one for each of the color toner cartridges)

18 Step 6: Installing the Consumables

EN

EN

To install the imaging drum

N o t e

Make sure that the printer is off (power button out) before installing the imaging drum.

1

2

Open the front door of the printer (A).

Swing the upper (blue) lever to the right (B). Press the white button on the lower (green) lever and swing the lever to the right (C).

Remove the imaging drum from its packaging.

C a u t i o n

There is a cover (D) protecting the drum’s cylinder. Do not remove this cover or the drum might be damaged; it will come off when you perform step 3, below.

3

4

Push the drum into the printer. The protective cover will slide off as the drum enters the printer. Set the cover aside.

Swing the lower (green) lever back to the left, making sure it clicks into place.

N o t e

If the lever does not return to its original position, make sure that the imaging drum is all the way in the printer.

Step 6: Installing the Consumables 19

20 Step 6: Installing the Consumables

To install the black toner cartridge

1 Remove the black toner cartridge from its packaging and gently rock the cartridge several times to distribute the toner.

C a u t i o n

Do not lift or remove the shutter (A) on the cartridge.

2

3

Align the arrow on the top of the cartridge with the arrow at the top of the slot in the printer and slide the cartridge into the printer.

Place one hand on the cartridge and use the other hand to pull the orange ring and remove the seal. Discard the seal.

N o t e

If toner gets on fabric, wipe the toner off with a dry cloth and then wash the clothing in cold water. Warm water or the heat of a dryer will set toner into fabric.

4 Swing the upper (blue) lever back to the left.

N o t e

If the lever does not return to its original position, make sure that the black toner cartridge and the imaging drum are all the way in the printer and that the orange seal was removed from the toner cartridge.

EN

To install the color toner cartridges

1

2

Turn the printer on (power button in).

Press the blue button beneath the clear door to turn the color toner carousel to the slot marked with a yellow sticker.

N o t e

The carousel will not rotate unless the clear door is closed, the imaging drum and black toner cartridge are installed completely (including removing the orange seal from the black toner cartridge and swinging the upper lever to the left), and the upper right door is closed.

3

4

Open the clear door.

Push the (blue) locking lever to the right.

EN

Step 6: Installing the Consumables 21

22 Step 6: Installing the Consumables

5 Remove the toner cartridge that matches the color of the sticker in the carousel slot from its packaging and gently rock the cartridge several times to distribute the toner.

C a u t i o n

Do not lift or remove the shutter (A) on the cartridge.

6 Align the arrow on the top of the cartridge with the arrow at the top of the slot and slide the cartridge into the printer.

N o t e

If the cartridge does not slide completely into the printer, make sure that the color of toner in the cartridge matches the colored sticker on the slot.

7

8

Place one hand on the cartridge and use the other hand to pull the orange ring and remove the seal. Discard the seal.

Push the blue locking lever back to the left.

N o t e

If toner gets on fabric, wipe the toner off with a dry cloth and then wash the clothing in cold water. Warm water or the heat of a dryer will set toner into fabric.

EN

9 Close the clear door.

N o t e

If the clear door does not close, make sure that the blue locking lever is all the way to the left and that the seal has been completely removed from the toner cartridge.

10

11

12

Press the blue button to rotate the carousel to the slot marked with a magenta sticker and repeat steps 3 through 9.

Press the blue button to rotate the carousel to the slot marked with a cyan (blue) sticker and repeat steps 3 through 9.

Close the front door.

N o t e

To prevent damage to the printer, do not move the printer after the imaging drum or any of the toner cartridges have been installed.

EN

Step 6: Installing the Consumables 23

advertisement

Related manuals

advertisement