Front-Panel Indicators. Mitsubishi Electronics WD-52631


Add to my manuals
108 Pages

advertisement

Front-Panel Indicators. Mitsubishi Electronics WD-52631 | Manualzz

16 Chapter 1. Television Overview

Front-Panel Indicators

Off Steady On Slow Blinking Fast Blinking

LAMP Indicator

LED Color TV Condition

None

Additional Information

Normal TV on or standby condition.

Normal operation.

Green

Yellow

TV just powered off and lamp is cooling.

1. Lamp access door is open or not secure.

Starts to blink 30 seconds after turning off TV. TV can be turned on before blinking starts or after blinking stops, but not while the indicator is blinking. Normal operation.

TV will not operate until lamp access door is secure. See Appendix C for installation information.

Red

2. No lamp installed.

Lamp no longer illuminates and has reached the end of the lamp life.

TV will not operate without a lamp. See Appendix C for installation information.

Replace the lamp. The TV will not operate when the lamp no longer illuminates. See Appendix C for installation information.

STATUS Indicator

LED Color TV Condition

None

Additional Information

Normal TV on or standby condition. Normal operation.

Yellow

Red

Room temperature is too high.

TV may require service.

TV will not operate when the ambient room temperature is too high. Turn off the TV and wait until the room temperature drops.

Turn off the TV and unplug the set from the AC power source.

Wait one minute and then plug the set back in.

If the LED is still on, contact your dealer or a Mitsubishi Authorized

Service Center. See www.mitsubishi-tv.com or call 1-800-332-

2119 to receive Authorized Service Center information.

POWER/TIMER Indicator

LED Color TV Condition

None TV is powered off.

Green

Green

Green

TV is powered on.

1. TV just plugged into AC outlet.

2. AC just restored after power failure.

3. TV Rebooting after System

Reset used.

4. TV Rebooting after power fluctuation or receiving abnormal digital signals from digital channel, CableCARD™, or digital device.

5. You have begun the procedure to update software from an authorized flash memory device.

TV is powered off and auto-on timer is set.

Additional Information

Normal operation.

Normal operation.

Wait until blinking stops before turning on (approximately 1 minute). Normal operation.

For detailed information, see the instructions that accompany the authorized software update. Important: Do not use unauthorized software at any time.

Normal operation. TV can be turned on at any time.

CableCARD™ Technology

(models WD-57731 and WD-65731)

CableCARD is a nationwide system standard that allows your local cable TV provider to supply you with an access card customized to your account. This card allows your

TV to receive, decode, and unscramble the premium digital channels included in your cable TV subscription without the use of a cable box. When you move to a new cable provider’s area, return the CableCARD to the original cable provider and get a new card from your new provider.

Please note that CableCARD is a relatively new technology and your local cable provider may not currently be offering this service. As time passes, this system will become broadly supported by most cable providers.

The CableCARD system is unidirectional, meaning your cable provider can send updates to the TV, but the TV cannot send signals back. As a result, certain advanced and interactive digital cable services, such as requests for video-on-demand and pay-per-view programs, a cable operator’s enhanced program guide, and data-enhanced television services may require use of a set-top box instead. For more information, call your local cable operator.

Digital cable channels authorized by the CableCARD are available on the Firewire® IEEE 1394 network and can be shared by other products on the network. You may be unable to record or copy some digital programs, however, because of copy restrictions set by the content or copyright owners.

Using a CableCARD™

Power on the TV and insert the CableCARD into the

CableCARD slot with the top of the card oriented as indicated by CARD TOP . When the initial screen displays, write down the information that appears and have it ready when calling your cable provider.

In order to start cable service for this device, please contact your cable provider

1-800-xxx-xxxx

CableCARD(tm): xxx-xxx-xxx-xxx-xxx-x

Host: xxx-xxx-xxx-xxx-x

Data: xxx-xxx-xxx-xx

UnitAddress: xx-xxxxx-xxxxx-xxx

Press EXIT to exit.

Sample CableCARD initial screen. Record the information before contacting your cable provider.

To review the information later, press MENU and when the

Main menu appears, press 9 9 9 to re-display the screen.

Note: CableCARD™ requires the TV’s Fast Power On setting. If you insert a CableCARD™, the TV will automatically override a Low Power setting and change to the Fast Power On setting.

Chapter 1. Television Overview

CableCARD™ Menu

CableCARD menu

Network Setup

CableCARD(tm) Status

CableCARD(tm) Pairing

Conditional Access

Press ENTER to select an application. Press EXIT key to exit.

IMPORTANT

Most CableCARD screens show only status or diagnostic information and do not allow you to make changes. These screens are meaningful only to your local cable provider.

IMPORTANT

To use a CableCARD, connect the primary incoming cable to ANT 1/MAIN on the TV.

17

Sample CableCARD menu

To display the CableCARD menu with links to applications from your cable provider:

1. While watching CableCARD, press INPUT to open the

Input Selection menu.

2. With the CableCARD icon highlighted, press MENU to open the CableCARD menu.

3. Press to highlight a link (blue text), then press

ENTER to access the linked page.

4. To redisplay the CableCARD menu, repeat steps 1 and

2.

5. Press EXIT to return to TV viewing.

If there are technical problems with the CableCARD, an error screen automatically displays with information that may be needed by your cable provider when you call them for assistance.

Moving Through Other CableCARD Screens

In addition to CableCARD menus, other CableCARD application screens may display and require you to make additional selections. When using these screens on your

Mitsubishi television:

• Blue text denotes a link to another screen. Press ENTER to move to the next application. Screens without blue text contain no links.

• You cannot move backward through the links. To exit the CableCARD system, press EXIT. The CANCEL key may not work with some CableCARD screens.

All information on these application screens is provided by your local cable company. Contact your cable provider if you have any problems with the application screen displays.

18 Chapter 1. Television Overview

TV Back Panel

3 6 4

ANT2 / AUX

ANT 1 and ANT 2 on WD-52631

ANT1 / MAIN �������

�����

������

����

������

������

�����

�����������

������������������

�����������������������������������

�����

�����������������������

�����������������������������

����������������������

������������������������

����������������

� �

��

��

�����

����

������

�����

�����������

��������

����������

�����

�����

1

���������

� �

10

�������

���

�����

����

�����

����

�����

�����

���

11

����

������

�����

�����

2

�������

�����

���

����������

��������

������������������

���������

� ���� �

��������

�������

����

12 9 5 7 8

1. ANT 1/MAIN, ANT 2/AUX (Antenna)

If you are connecting an antenna, direct cable without a cable box, or are using cable with a CableCARD™, connect the main antenna or cable source to

ANT 1/MAIN.

ANT 1/MAIN and ANT 2/AUX can each receive both digital and analog over-the-air channels from a VHF/UHF antenna or non-scrambled digital/analog cable source.

ANT 1/MAIN and CableCARD™ (models WD-57731 and

WD-65731)

Use ANT 1/MAIN to receive premium subscription cable

TV service authorized by the CableCARD™ access card.

The CableCARD access card is provided by your local cable company. ANT 2/AUX can continue to receive over-the-air or non-scrambled cable signals when ANT 1 is used for CableCARD™ service.

2. CableCARD™ Slot

(models WD-57731 and WD-65731)

The CableCARD access card from your cable TV service provider is inserted into this slot. When inserting, ensure that the top of the card faces in the direction indicated by

CARD TOP .

If your cable company is not currently offering CableCARD access cards, use the cable box provided and authorized by your local cable company to view scrambled channels.

3. INPUT 1 and 2 Inputs

(Audio and Video)

INPUT 1 and 2 can be used to connect a VCR, Super

VHS (S-VHS) VCR, DVD player, standard satellite receiver, or other A/V device to the TV. INPUT 3 is a third set of jacks located on or near the front of the TV for convenience. Please note that if S-VIDEO and VIDEO are both available, you must choose to connect only one.

Chapter 1. Television Overview 19

TV Back Panel, continued

4. COMPONENT 1 and 2 Inputs

(Audio and Video)

Y Pb Pr (480i/480p/720p/1080i)

Use these jacks to connect devices with component video outputs, such as DVD players, external HDTV receivers, or compatible video game systems. Please see Appendix B for signal compatibility.

5. HDMI™ 1 and 2

Do not connect a computer to either HDMI jack.

The HDMI (High Definition Multimedia Interface) supports uncompressed standard and high-definition digital video formats and PCM digital audio format. For PC video, use the PC-DVI input instead.

Use these inputs to connect to EIA/CEA-861 compliant devices such as a high-definition receiver or DVD player.

These inputs support 480i, 480p, 720p, 1080i, and 1080p video formats.

These inputs can also accept DVI video inputs. To connect a DVI input, use an HDMI-to-DVI adapter or cable plus analog audio cables. Connect the analog audio cables to the HDMI/DVI AUDIO inputs on the TV to receive left and right stereo audio from your DVI device.

These inputs are HDCP (High-Bandwidth Digital Copy Protection) compliant.

8. PC-DVI AUDIO

Use the PC-DVI AUDIO jacks in conjunction with the

PC-DVI video input from a personal computer. These jacks allow you to send left and right analog audio from your computer to the TV.

9. DTVLINK™/IEEE 1394

These jacks allow the TV to connect to external IEEE 1394 digital products by means of a single cable. See chapter

7, “Using IEEE 1394 Devices” for detailed information regarding IEEE 1394 connections and recording.

10. MONITOR OUT

Use these composite video and left/right audio jacks to send analog video and audio signals to an external recording device such as a VCR. The signals from these jacks are from the program currently being viewed on the

TV screen. To make recordings from this output, the

TV must be in normal full-screen mode rather than in

mode.

• From this output you can record audio and video signals from ANT 1, ANT 2, INPUT 1-3, and

IEEE 1394 devices.

• Digital signals from ANT 1, ANT 2, and IEEE

1394 devices are converted to analog video and audio signals.

• Some signals cannot be recorded because of copy-protection flags in the content.

These inputs are certified for proper interoperability with other products certified by Simplay™.

6. HDMI/DVI AUDIO

Use these analog audio inputs when connecting DVI video devices to the TV’s HDMI jacks. Unlike HDMI, DVI does not carry audio information on the same cable.

For analog audio from a personal computer, use the PC-

DVI AUDIO jacks instead.

11. AUDIO OUT LEFT/RIGHT

AUDIO OUT LEFT/RIGHT jacks send analog audio of the program currently shown on the screen to an A/V surround sound receiver or stereo system. Digital audio from digital channels, FireWire® (DTVLink/IEEE 1394) devices and HDMI devices is converted to analog audio by the TV.

If using an analog A/V receiver or stereo system, this is the only audio connection needed between it and the TV.

7. PC-DVI

Do not connect a TV video source to the PC-DVI input.

PC-DVI is a DVI-I input compatible with both DVI-A

(analog) and DVI-D (digital) inputs. Connect your personal computer’s HDMI, DVI, or VGA video output to this jack.

An adapter or converter cable may be required. Please see Appendix B for signal compatibility. To hear audio from the computer, connect analog audio cables from the computer to the PC-DVI AUDIO jacks.

12. DIGITAL AUDIO OUT

This output sends Dolby Digital or PCM digital audio to your digital A/V surround sound receiver. Analog audio from analog channels and devices is converted by the TV to PCM digital audio. If you have a digital A/V receiver, in most cases this is the only audio connection needed between the

TV and your A/V receiver.

2

TV Connections

Before You Begin

Choosing a Language for Menus . . . . . . . . . . . . . . . . . . . . . . . . . . 22

ClearThought® Easy Connect Auto Input Sensing . . . . . . . . . . . . . . . 22

Digital Video and Home Recording . . . . . . . . . . . . . . . . . . . . . . . . 23

Connection Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

HDTV Cable Box or Satellite Receiver with Component Video

. . . .

25

Standard Cable Box, Satellite Receiver, or Other Device with

S-Video

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

25

Wall Outlet Cable (no cable box)

. . . . . . . . . . . . . . . . . . . . . . . . .

26

Antenna with a Single Lead

. . . . . . . . . . . . . . . . . . . . . . . . . . . .

27

Antennas with Separate UHF and VHF Leads

. . . . . . . . . . . . . . . .

27

VCR to an Antenna or Wall Outlet Cable

. . . . . . . . . . . . . . . . . . .

28

VCR to a Cable Box (Audio & Video)

. . . . . . . . . . . . . . . . . . . . . .

29

HDMI Device (Cable Box, Satellite Receiver, DVD Player, or

Other Device)

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

30

DVI Video Device (Cable Box, Satellite Receiver, DVD Player, or Other Device)

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

30

DVD Player with Component Video

. . . . . . . . . . . . . . . . . . . . . . .

31

A/V Receiver (Stereo System)

. . . . . . . . . . . . . . . . . . . . . . . . . .

31

Older Cable Box

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

32

Camcorder

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

32

22 Chapter 2. TV Connections

Before You Begin

Choosing a Language for Menus

When you power on the TV for the first time, you can select either English or Spanish for all menus. You can later change the language through the Setup menu.

3. Press EXIT to close the screen. If you connected several devices at the same time, the screen for the next connection will open.

Figure 1. The Welcome screen lets you change the menu language when you first power on the TV.

ClearThought® Easy Connect Auto Input

Sensing

This TV’s ClearThought® auto input sensing feature allows it to detect most connections automatically. The first time you connect each device you will be prompted to identify it by selecting from a pre-set list of device names. The table below defines how connections on each TV jack are handled.

Auto Detection Active

INPUT 1, 2, 3 video jacks

No Auto Detection

ANT 1/ANT 2

COMPONENT video jacks MONITOR OUT

HDMI* (all jacks)

PC-DVI*

IEEE 1394

All AUDIO jacks

If the device is powered off when connected, detection will occur when the device is next powered on.

1. Connect your devices to the TV.

The TV and the devices can be either on or off when connecting. If the TV is powered off, the detection process will occur the next time you turn on the TV.

2. When the Auto Input Sensing screen opens (figure

2), you can accept the default name or press to select from a list of device names (e.g., cable box,

DVD, Satellite, VCR).

Choose a name that will help you when selecting inputs in the Input Selection menu.

Figure 2. The Auto Input Sensing screen appears when a device is first detected. Select a name for the connected device in this screen.

More About Auto Input Sensing

• You can change the input name at a later time using the Input Name menu.

• If you disconnect a device and then later connect a different device to the unused jack, open the Input

Name menu to update the device name.

• Antenna inputs ( ANT 1/ANT 2) and TV outputs are never detected.

• Be careful to choose different names for each input.

IEEE 1394 Connections

The screen in figure 3 appears when you make an IEEE

1394 connection, The TV can recognize up to seven IEEE

1394 devices at one time. If you connect more than one device of the same type, a unique identifier is added to the name for each one. For example, if you connect three A/V discs, you may see AV Disc, AV Disc1, AV Disc2.

IEEE 1394 Device with an Analog Connection.

Some IEEE 1394 devices have both digital and analog outputs to the TV. If you have such a device, place a check mark in the Analog Connection check box to:

• Allow a cable box with both analog and digital outputs to switch automatically between them.

• Allow you to use a TV menu to select either the analog or digital output from the device.

For instructions on switching between analog and digital outputs, see chapter 7, “Using IEEE 1394 Devices.”

Chapter 2. TV Connections 23

Before You Begin, continued

Name assigned to the device device, as later changes can only be made after returning all TV settings to their defaults.

3. In the New 1394 Device screen, note the name assigned to the device, as you will need to use the same name in a later step. See figure 3.

4. Connect the device to the TV with the supplemental analog cables.

5. The next screen is the Auto Input Sensing screen

(see figure 2) in which you can select a name for the device. Select the same name you noted in the New

1394 Device screen (see figure 3).

• If you select the wrong name for the device, you will be unable to switch between the analog and digital inputs to the TV.

• If you connect an IEEE 1394 cable box and it is detected as CABLE in the New 1394 Device screen, be sure to select the name CABLE as the name for the analog input and not cablebox.

Figure 3. The ClearThought Auto Input Sensing screen for

IEEE 1394 devices includes a check box for an associated analog connection.

If your IEEE 1394 device has an analog connection to the

TV, follow the instructions below.

1. Connect the device to the TV with an IEEE 1394 cable first.

2. When the New 1394 Device screen appears with the

Analog Connection check box highlighted, press

ENTER to enter a check mark. See figure 3, New 1394

Device screen.

Note: It is important to check mark the box when this screen appears upon first connecting the

To Add an Analog Connection at a Later Time (not recommended)

1. Disconnect the IEEE 1394 device from the TV.

2. Reset all TV settings to their defaults using the TV

Reset service menu as follows: a. Press MENU to display the Main menu.

b. Press 1 2 3 to open the Reset service menu.

c. Press ENTER.

3. Reconnect the IEEE 1394 device to the TV, using the

IEEE 1394 cable first.

4. When the TV recognizes the device, place a check in the Analog Connection check box.

5. Press EXIT.

Digital Video and Home Recording

The table below will help you decide which type of connection to use for digital video. Digital video comes to your home in a compressed state, whether received on recorded media (e.g., disc) or broadcast over the air, over cable, or via satellite. Some compressed digital video is available for recording as noted in the table.

Connection Type into the TV

HDMI or DVI

Compressed video is converted to uncompressed form by an external device such as a cable box, satellite receiver, or

DVD player before it is sent to the TV on an

HDMI or DVI cable.

IEEE 1394 (FireWire®) Connections

Your TV can receive and decode digital channels, MPEG2 compressed digital video, and Dolby Digital audio.

Effect on Home Recording

You cannot record the resultant uncompressed video sent to the TV via HDMI or DVI.

You can record compressed digital video either

• on compatible digital recorders as digital signals using IEEE 1394 connections

• converted to analog signals and recorded as standard-definition composite video from the MONITOR OUT jack

You may be unable to record some programming because of copy restrictions added by the content owners.

24 Chapter 2. TV Connections

Connection Types

Video and Combined Audio/Video Connections

These descriptions apply to TV video only and do not cover signals from personal computers.

Picture Quality

(most sources)

Name Signal Type

Figures

(not to scale)

Best

(carry highdefinition video when available)

DVI

Good

Fair

Fair to Best

(depending on source; carry all qualities of signals)

HDMI

Digital audio and video

Digital and analog video

Component Video Analog video

S-Video Analog video

Composite Video Analog video

IEEE 1394

(FireWire®)

RF Coaxial Video

Digital audio and video

Analog and digital audio and video

Additional Information

Carries digital audio and uncompressed digital video on a single one-way cable.

Carries uncompressed digital or analog video on a single oneway cable; requires separate audio connections.

Carries analog high-definition and standard-definition signals.

Y Pb Pr RCA-style connectors are colored green, blue, and red.

Carries analog standard-definition signals. Provides better quality video than composite or

RF coaxial video.

Carries analog standard-definition signals. RCA-style connector, usually colored yellow

Carries compressed digital video and audio as well as device control signals on a single two-way cable.

Carries audio and video on a single cable.

Note: Only some TV signals are high-definition signals. To view high-definition programming from your cable or satellite provider, you must subscribe to the provider’s high-definition service. Some over-the-air broadcasts are in high-definition and can be received with a high-quality antenna suited to your location.

Audio-Only Connections

There are two types of audio connections used on this TV. Refer to the table below.

Audio Connection

Figures

(not to scale)

Left/Right Analog

Stereo Audio

Digital Audio (Coaxial)

Additional Information

RCA-style connectors usually colored white for left and red for right stereo audio. For monaural sound (all speakers playing the same sound), use only the white connector.

RCA-style connector usually colored orange. Use to send digital audio from the TV to your digital A/V receiver for surround-sound effects. Usually the only audio connection required between the TV and the A/V receiver.

Chapter 2. TV Connections 25

HDTV Cable Box or Satellite

Receiver with Component Video

If your cable box or satellite receiver has HDMI or DVI outputs, use the connections for HDMI or DVI video devices described later in this chapter.

Required: RCA component video cables, left/right analog audio cables.

A coaxial splitter, available at most electronic supply stores, may be required to complete this installation.

1. Connect the cable from the outside cable or satellite service to CABLE IN or SATELLITE IN on the cable box or satellite receiver. See your device’s owner’s guide for instructions and cable compatibility.

��

��

�������

�����

������

����

������

������

�����

�����������

�����

������������������

�����������������������������������

��������������������������������������������

�����������������������

�����������������������������

����������������������

������������������������

����������������

� �

��

��

�����

����

������

�����

�����

��������

����������

���������

� �

�����

�������

���

�����

����

�����

����

�����

�����

���

����

������

�����

����� trial antenna or cable service (not satellite) to ANT

1/MAIN on the TV back panel. A coaxial splitter, available at most electronics supply stores, may be required to complete this installation.

Note: To receive the benefits of digital surround sound, connect the digital audio output from your cable box or satellite receiver directly to your digital A/V receiver.

Standard Cable Box, Satellite

Receiver, or Other Device with

S-Video

Required: S-Video cable and left/right analog stereo audio cables.

1. Connect the cable from the outside cable or satellite service to CABLE IN or SATELLITE IN on the cable box or satellite receiver.

2. Connect an S-Video cable from VIDEO OUT on the cable box or satellite receiver back panel to INPUT

S-VIDEO on the TV back panel.

3. Connect left (white) and right (red) audio cables from

AUDIO OUT on the cable box or satellite receiver to

INPUT/AUDIO LEFT and AUDIO RIGHT on the

TV back panel.

Note: Refer to the cable box or satellite receiver Owner’s

Guide for cable or dish antenna connections to the receiver.

������������������

���������

��

���������

������������

������������

�������

�����

���

���������� �

��������

������������������

���������

����

��������

�������

���� ��

��

���������

�����������

����

Figure 4. Connecting an external HDTV receiver with component video connections

2. Connect RCA-type cables from the Y Pb Pr outputs on the HDTV cable box or satellite receiver to COM-

PONENT on the TV back panel, matching the colored connections.

3. Connect left (white) and right (red) audio cables from the HDTV cable box or satellite receiver to COMPO-

NENT /AUDIO LEFT and AUDIO RIGHT on the

TV back panel.

4. Optional: To allow use of the Split Screen feature with channels from ANT 1 and the cable box or satellite receiver, connect the incoming terres-

��

�������������

��

�������

�����

������

����

������

�����������

������������������

�����������������������������������

��

�����������������������

�����������������������������

����������������������

������������������������

����������������

� �

��

��

�����

����

������

�����

�����������

��������

����������

�����

�����

���������

� �

Figure 5. Connecting a device with S-Video

��������

������������������

� ���� �

��������

��������� �������

�����

���

�������

����

�������

���

�����

����

�����

����

�����

�����

���

����

�����

������

�����

26 Chapter 2. TV Connections

Wall Outlet Cable (no cable box)

(can be used with a CableCARD™, models WD-57731 and 65731)

It is very important to connect the incoming cable for your primary viewing source to ANT 1/MAIN, especially for

CableCARD™ use.

1. Connect the primary incoming coaxial lead cable to

ANT 1/MAIN on the TV back panel.

2. For an optional secondary antenna source, connect an antenna (or cable) to ANT 2/AUX.

3. If you have subscribed to a CableCARD™ service,

Insert the CableCARD into the CableCARD slot. The top of the card must face in the direction indicated by the CARD TOP arrow.

See chapter 1, “Television Overview,” for additional

CableCARD information.

��� �������������

������������

�������������

�������

�����

������

����

������

������

�����

�����

������������������

�����������������������������������

��

�����������������������

�����������������������������

����������������������

������������������������

����������������

� �

��

��

�����

����

������

�����

�����

���������

� �

��� ���������

����������

�����������

�����

������������

�������

���

�����

����

�����

����

�����

�����

���

����

������

�����

�����

����������

��� ������������

����

�������

�����

���

��������������������

Figure 6. Wall Outlet Cable

���������

� ���� �

��������

�������

����

Chapter 2. TV Connections 27

Antenna with a Single Lead

A. For an antenna with flat twin leads

A 300-ohm-to-75-ohm transformer is required. This is not included with the TV, but is available at most electronics stores.

Antennas with Separate UHF and

VHF Leads

Required: UHF/VHF combiner

A1. For an antenna with flat twin leads, connect the 300ohm twin leads to the 300-ohm-to-75-ohm transformer.

A2. Push the 75-ohm side of the transformer onto on the TV back panel.

�������

ANT 1 electronics stores.

VHF combiner.

������

����

������

2. Push the combiner onto back panel.

� ���

ANT 1/MAIN on the TV

������

�����

� �����

�����

��

Connect the coaxial lead directly to back panel.

�����������������������������������

��������������������������������������������

ANT 1 on the TV

������

������

�����

�����

����

������

������������

���������������

� �

��������

����� �����������

�����

����������� ��������

����������

�����

�����

�������������

����������������

���������������

����

����

�����

����

�����

���

�����������

������������������

�����������������������������������

�����������������������

�����������������������������

����������������������

������������������������

����������� ��������

����������

�����

����

������

�����

�����

����������������

� �

������

�����

�����

����������

��������

������������������

��������

�������

�������� � ���� �

���������

�������

�����

��� ����������

� �������� ������������������

��

��

���������

� �

��������

��������

����

������

�����

��

�������

�����

���

���������

� ���� �

��������

�������

����

�����������

�������

��������

���

���

��

�������������

�������������

����

����

���

����

����

��

���

���������

��������������������

Figure 8. Connecting separate UHF and VHF Antennas

�������

����

�������

���

�����

����

�����

����

�����

�����

���

����

������

�����

�����

Figure 7. Connecting a Single Antenna

Mitsubishi strongly recommends you avoid using antennas with flat twin leads. Flat twin lead antenna wires are subject to interference which may adversely affect the performance of the TV.

We recommend using coaxial antenna cable.

28 Chapter 2. TV Connections

VCR to an Antenna or Wall Outlet

Cable

Required: Two-way RF splitter, 3 coaxial cables, right and left analog audio cables, either S-video or video cable.

These are not included with the TV but are available at most electronics stores.

1. Connect the incoming cable or antenna to IN on the

RF splitter.

2. Connect one coaxial cable from OUT on the RF splitter to ANTENNA IN on the VCR back panel.

3. Connect one coaxial cable from OUT on the RF splitter to ANT 1/MAIN on the TV back panel.

4. To use the TV speakers with the VCR, connect left

(white) and right (red) audio cables from AUDIO

OUT on the VCR to INPUT/AUDIO LEFT and

AUDIO RIGHT on the TV back panel. If your VCR is mono (non-stereo), connect only the white (left) cable.

5. Connect either an S-Video or composite video cable from VIDEO OUT on the VCR back panel to

INPUT/VIDEO or S-VIDEO on the TV back panel.

Connect only one type of video cable; S-Video is recommended, if available.

Optional

To record high-definition digital channels converted to analog standard-definition video and analog stereo audio, perform these two additional steps.

6. Connect left (white) and right (red) audio cables from AUDIO IN on the VCR to MONITOR OUT

LEFT/RIGHT on the TV back panel. If your VCR is mono (non-stereo), connect only the white (left) cable.

7. Connect a composite video cable from VIDEO

IN on the VCR back panel to MONITOR OUT/

VIDEO on the TV back panel.

��

��

��������������

�������

��

�����

��� ��

���

������

��

��

��

������������

�����������������

�������

��� ��

��

��

��

�������������

�������

��

�����

������

����

������

������

�����

���������

�����

��

�����������

��

�����������

�� ��

Figure 9. Connecting a VCR to an Antenna or Wall Outlet Cable

����������

��������

������������������

��

������������������������

����������������������

���������������

����������

�������������

��

���������

� �

������������������

��

�����������������������

�����������������������������

��

�����

����

������

����������������

� �

��

�����

�����

��������

����������

� ���� �

��������

���������

�������

�����

���

�������

����

�������

���

����

�����

���

�����

����

�����

������

�����

Chapter 2. TV Connections 29

VCR to a Cable Box (Audio & Video)

Required: Two-way RF splitter, 4 coaxial cables, right and left audio cables, S-Video or composite video cable, plus component or S-Video cables and audio cables required to connect the TV to the cable box.

1. Connect the incoming cable to IN on the RF splitter.

2. Connect one coaxial cable from OUT on the RF splitter to CABLE IN on the cable box.

3. Connect one coaxial cable from OUT on the RF splitter to ANT 1/MAIN on the TV back panel.

4. Connect one coaxial cable from OUT on the cable box to ANTENNA IN on the VCR back panel.

5. Connect the cable box outputs to the TV as shown in either figure 4 or figure 5, earlier in this chapter. This connection allows the TV to receive the best available signal directly from the cable box.

Figure 4: Component video output to the TV’s

COMPONENT Y Pb Pr jacks; analog stereo audio to the associated AUDIO jacks.

Figure 5: S-Video output to the TV’s

INPUT/S-VIDEO jack; analog stereo audio to the associated AUDIO jacks.

6. To use the TV speakers with the VCR, connect left

(white) and right (red) audio cables from AUDIO

OUT on the VCR back panel to INPUT/AUDIO

LEFT and AUDIO RIGHT on the TV back panel.

If your VCR is mono (non-stereo), connect only the white (left) cable.

7. Connect either an S-Video or composite video cable from VIDEO OUT on the VCR back panel to

INPUT/VIDEO or INPUT/S-VIDEO on the TV back panel. Connect only one type of video cable. S-

Video is recommended, if available.

Optional

8. To allow recording from the TV to the VCR: a. Connect left (white) and right (red) audio cables from AUDIO IN on the VCR back panel to

MONITOR OUT/LEFT and RIGHT on the TV back panel.

b. Connect a video cable from VIDEO IN on the

VCR back panel to MONITOR OUT/VIDEO on the TV back panel.

Note: When using this connection configuration with the connections used in step 5, it is possible to view live cable programs through the VCR Device. For best picture quality always view live cable programs directly from the cable box device.

��

��������������

���

���

�������

��� ��

�����

��� ��

���������

��

��

��

����������������

���������������

�����

��

�����������

��

Figure 10. Connecting a VCR to a cable box

��

���������������������

����������������

�������������

��

��

�������

�����

������

����

������

������

�����

�����������

�� ���

������������������

�����������������������������������

R ����������������

�����

����������������

� �

��

��

�����

����

������

�����

�����

��������

����������

���������

� �

�������������

��

���������� �

��������

������������������

���������

�������

�����

���

� ���� �

��������

�������

����

�������

���

�����

����

�����

����

�����

�����

���

����

�����

������

�����

���

���

��

��

30 Chapter 2. TV Connections

HDMI Device (Cable Box, Satellite

Receiver, DVD Player, or Other Device)

������� the TV.

�����

�����

������������������

�����������������������������������

R

Connect an HDMI cable from the TV back panel to the

������

������

�����

����������������������

������������������������

�����

����

������

����������������

��

��

����

�����

HDMI device output. HDMI devices provide video and

���� audio through this cable, so no other connection is

�����������

�����

��������

����������

�����

�����

�����

�����

��� required. There are two HDMI inputs on the TV back panel.

����

������

�����

�����

���������� �

��������

������������������

�������

�����

���

�������������

���������

� ���� �

�����������

��������

�������

����

Figure 11. Connecting an HDMI device.

DVI Video Device (Cable Box,

Satellite Receiver, DVD Player, or

Other Device)

Analog stereo audio cables and a DVI-to-HDMI cable or

DVI/HDMI adapter and HDMI cable are required. These are not included with the TV. They may be available at your local electronics retailer.

1. Connect the DVI-to-HDMI cable (recommended) or

HDMI cable with DVI/HDMI adapter from the DVI device’s back panel to the TV back panel.

NOTE: If you are using a DVI/HDMI adapter, it is important to connect the adapter to the DVI device for best performance.

2. Connect a set of audio cables from AUDIO OUT on the DVI device back panel to the HDMI/DVI

AUDIO on the TV back panel. Connect the red cable to the RIGHT jack and the white cable to the

LEFT jack.

NOTE: The HDMI connection supports copy protection

(HDCP).

Some devices require connecting to an analog input first, in order to view on-screen menus and to select DVI as the ouput. Please review your equipment instructions for DVI connectivity and compatibility.

Note: HDMI inputs are certified for proper interoperability with other products certified by Simplay™.

�������

�����

������

����

������

������

�����

�����������

�����

������������������

�����������������������������������

�����

�����������������������

�����������������������������

����������������������

������������������������

�����

����

������

�����

�����

����������� ��������

����������

��

��

���������

� �

�������

���

�����

����

�����

����

�����

�����

���

����

������

�����

�����

��

IMPORTANT

For sound from your devices, note that the

HDMI inputs can receive digital stereo audio signals only. To use digital surround sound for an HDMI or DVI device, connect that device’s digital audio output directly to your A/V receiver. See the Owner’s Guides for those devices for instructions.

���������� �

��������

������������������

���������

�������

�����

���

������������� ��

����

��������

�������

����

�����������������

��

����������

��

IMPORTANT

To connect a personal computer to the TV, see chapter 6, “Using the TV with a Personal

Computer.”

The HDMI input processes signals as standard motion video and is not designed to process computer resolutions.

�������

Figure 12. Connecting a DVI device

Chapter 2. TV Connections 31

DVD Player with Component Video

Component video cables and analog audio cables are required. These are not included with the TV.

1. Connect the component video cables from Y PB PR

VIDEO OUT on the back of the DVD player to the

COMPONENT jacks on the TV back panel, matching the red, green, and blue colored connections.

2. Connect left (white) and right (red) stereo audio cables from AUDIO OUT on the back of the DVD player to COMPONENT/AUDIO LEFT and

RIGHT on the TV back panel.

�������

�����

������

����

������

������

�����

�����������

������������������

�����������������������������������

��

�����������������������

�����������������������������

����������������

� �

�����

����

������

�����

����������� ��������

����������

�����

�����

���������

� �

�������

���

�����

����

�����

����

�����

�����

���

����

�����

������

�����

��

��

A/V Receiver (Stereo System)

Most setups require either a digital audio cable or analog stereo audio cables.

The TV makes all audio available in digital and analog formats. Analog audio coming into the TV is available in digital format on the DIGITAL AUDIO OUT jack.

Digital incoming audio is available in analog format on the

AUDIO OUT LEFT/RIGHT jacks. Usually, only one of the following connections is required:

• To connect an analog A/V receiver

Connect left (white) and right (red) audio cables from

AUDIO OUT/LEFT and RIGHT on the TV back panel to the TV AUDIO INPUT on the A/V receiver.

• To connect a digital A/V receiver with Dolby

Digital surround sound and PCM audio support

Connect one end of the digital audio cable to

DIGITAL AUDIO OUT on the back of the TV.

Connect the other end to the COAXIAL DIGITAL

INPUT on the back of the A/V receiver.

����������

� �������� ������������������

�������

�����

���

�������������

���������

����

��������

�������

����

��

��

���������

���������������������

Figure 13. Connecting a DVD player with component video

IMPORTANT

See Appendix B for component video signal compatibility information.

For digital audio connections to your

A/V receiver, see your DVD player and A/V receiver Owner’s Guides.

�������

�����

������

����

������

������

�����

�����������

�����

�����������

������������������

��

�����������������������

�����������������������������

����������������������

������������������������

��

�����

����

������

����������������

� �

��

�����

�����

���������

� �

�������

���

�����

����

�����

�����

���

����

������

�����

�����

�������

�����

���

����������

������������������

���������

� ���� �

��������

�������

����

Figure 14. Connecting audio from the TV to an A/V receiver

Note:

On rare occasions, an HDMI signal may be copy-restricted and cannot be output from the TV as a digital signal. To hear these copy-protected signals through the A/V receiver, use connections for analog A/V receivers.

Check the A/V receiver’s Owner’s Guide for information concerning use of the digital input and switching between digital sound and analog stereo sound from the TV.

32 Chapter 2. TV Connections

Older Cable Box

Required: 3 coaxial cables, one two-way RF splitter.

These are not included with the TV.

When this setup is complete, you can use the TV remote control, when programmed, to change channels on the cable box.

Note: This connection is not recommended. The other connections described in this chapter provide better quality audio and video to the TV.

1. Connect the incoming cable to IN on the RF splitter.

2. Connect one coaxial cable from OUT on the RF splitter to ANT 1/MAIN on the TV back panel.

3. Connect one coaxial cable from OUT on the RF splitter to IN on the standard cable box.

���������

� �

�������

���

4. Connect one coaxial cable from box to

������

�����������������������������������

��

����������������������

R

�����������������������

�����������������������������

OUT on the cable

ANT 2/AUX on the TV back panel.

������������������������

������

�����

�����

����

������

�����

���

�����

�����

����������� �����������

������

�����

Camcorder

Required: Analog stereo audio cables and either an S-

Video or composite video cable.

NOTE: For IEEE 1394 camcorders, see also chapter 7,

“Using IEEE 1394 Devices.”

1. Connect either an S-Video or composite video cable from VIDEO OUT on the camcorder to INPUT

3/VIDEO or S-VIDEO on the TV. Connect only one type of video cable; S-Video is recommended, if available.

2. Connect left (white) and right (red) audio cables from

AUDIO OUT on the camcorder to INPUT 3/

AUDIO L and AUDIO R on the TV.

������������

��

�������

�����

���

���������� �

��������

�������������

��

��

��

��

����������

����������

��

�����������

�������������

��

���������

�����

�������

����

Figure 15. Connecting an older cable box

��

�������������

��

���������������������

��

��

Figure 16. Analog connections for a camcorder

3

TV Operation

Remote Control

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

34

Choosing a Program Source

. . . . . . . . . . . . . . . . . . . . . . . . . . .

36

ChannelView™ Channel Listings

. . . . . . . . . . . . . . . . . . . . . . . .

36

Status Display

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

37

TV Signals and Display Formats

. . . . . . . . . . . . . . . . . . . . . . . . .

38

Split Screen

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

40

34 Chapter 3. TV Operation

Remote Control

Overview

Figure 1, next page

1. Slide Switch: Selects the A/V device to be controlled by the remote control. Set the slide switch to TV for operation of the TV and IEEE 1394 devices. Control of other device types requires programing (see chapter

3, “TV Operation”).

2. SLEEP: Sets the TV to turn off within 2 hours. See the next page for instructions.

3. Digits/Letters: Allow you to tune to a channel by entering channel numbers; press ENTER for faster tuning. Use numbers and the CANCEL key to enter digital sub-channels. Also use for entering information into menus.

To select letters when naming channels, repeatedly press the associated number key. The following special characters are available with the 1 and 0 keys:

0

1 ! & blank space

/ * -

4. —/CANCEL (SUB-CHANNEL/CANCEL): When entering digital channel numbers, adds a separator between main and sub-channel numbers. Clears FAV and some menu entries.

5. POWER: Turns TV power on and off.

6. QV (QuickView™): Switches between the current channel and the last channel viewed.

7. MUTE: Turns TV sound off or on.

8. SPLIT: Turns Split Screen mode on and off.

9. VOL / (Volume Up/Down): Changes sound level.

10. CH/PAGE / (Channel or Page Up/Down): Scans up or down through memorized channels. Pages up and down through screens when used with

ChannelView™.

11 FAV (Favorites): Scans through memorized lists of favorite channels. See “Channel Menu” in chapter 4,

“TV Menu Settings,” for more information.

12. FORMAT: Changes the shape and size of the main TV picture. When in Split Screen mode, changes the

Note: The TV’s remote control can operate other audio/video devices.

• See chapter 5, “Operating Other Devices with the

Remote Control” for: instructions on programming the remote.

a list of functions available for controlling other devices.

• For control of IEEE 1394 devices, see chapter 7.

size of the split images while maintaining their aspect ratios.

13. INPUT: Displays the Input Selection menu from which you can select an input source to view, such as an antenna input ( ANT 1/2) or a connected device.

14. (Adjust Up/down/Left/Right): Navigate menus and change settings.

15. ENTER: Selects a channel number or menu item.

16. GUIDE: Displays or removes ChannelView™ on-screen channel listing for ANT 1 and ANT 2.

17. INFO: Displays an on-screen summary of the current device in use and any broadcast information available, including current V-Chip information. See chapter 3,

“TV Operation,” for details.

18. AUDIO: Selects individual audio settings for adjustment.

19. VIDEO: Selects individual video settings for adjustment.

20. MENU: Displays the main TV menu using the on-screen menu system. When a sub-menu is open, backs up one level.

21. EXIT: Closes all TV on-screen menus and displays and returns to normal TV viewing.

22. F1–F4: When programmed, work like the A, B, C, D buttons on some cable boxes and satellite receivers. Program the remote control for your equipment and test the keys. See chapter 5, “Operating Other

Devices with the Remote Control.”

24. (PAUSE): Freezes a broadcast TV picture when no

Split Screen image is displayed. When Split Screen is displayed, freezes the sub-picture. See below for use with recordable media.

Record/Playback Keys

To enable the recording and playback functions, program the remote for your VCR, DVR, or DVD player/recorder and set the slide switch to VCR or DVD. See chapter 5 for instructions on programming the remote. If you have an

IEEE 1394 device, see chapter 7 on IEEE 1394 devices.

23. (RECORD): Records with a VCR, DVR, or DVD recorder.

24. (PAUSE): Pauses a VCR, DVR, or DVD. See above for use during TV viewing.

25. (STOP): Stops play of a VCR, DVR, or DVD.

26. (REVERSE): Rewinds a VCR. Reverse scans a DVR or DVD.

27. (PLAY): Plays a VCR, DVR, or DVD.

28. (FAST FORWARD): Fast forwards a VCR. Forward scans a DVR or DVD.

Remote Control, continued

1

2

3

5

Chapter 3. TV Operation 35

3. Press EXIT or wait five seconds without pressing any buttons for the message to disappear.

4. Press SLEEP to view the time remaining before the sleep timer turns off the TV.

Cancelling the Sleep Timer

1. Press SLEEP to display the on-screen message.

2. Press SLEEP repeatedly until OFF is displayed.

Note: After five seconds of inactivity, the message box will disappear.

1

4

7

8

9

6

11

12

10

16

17

23 24

26 27

25

28

13

14

15

2

22

18

19

20

21

Figure 2. The remote control requires two AA alkaline batteries.

Care

For Best Results from the Remote Control:

• Use only alkaline batteries.

• Be within 20 feet of the equipment.

• Do not press two or more buttons at the same time unless instructed to do so.

• Do not allow unit to get wet or become heated.

• Avoid dropping on hard surfaces.

• Do not use harsh chemicals to clean. Use only a soft, lightly moistened cloth.

• Do not mix old and new batteries.

• Do not heat, take apart, or throw batteries into fire.

Figure 1. Remote Control Overview

Battery Installation

Figure 2

1. Remove the remote control’s back cover by gently pressing in the tab and lifting off the cover.

2. Load the batteries, making sure the polarities (+) and

(-) are correct. For best results, insert the negative (-) end first.

3. Snap the cover back in place.

Resetting the Remote Control

If the slide switch is set to TV and the TV does not respond properly, do the following to reset the remote control.

1. Press and hold POWER for several seconds until the button blinks twice and goes off.

2. Release the POWER button.

3. Press keys 0 0 9 3 5 and the POWER button will blink twice when you finish entering the code. While entering the code, pause for a moment between each key press to ensure it is recognized.

Sleep Timer

Setting the Sleep Timer

1. Press SLEEP on the remote control.

2. Press SLEEP additional times to increase the time in 30minute increments up to the maximum of 120 minutes.

Low-Battery Indicator

If you press a key and the POWER indicator blinks five times, replace the remote control’s batteries.

36 Chapter 3. TV Operation

Choosing a Program Source

NOTE: If your only viewing sources are connected to the

ANT 1 and ANT 2 antenna jacks, you can switch inputs without the Input Selection menu. Press

INPUT to switch between ANT 1 and ANT 2. To verify which is the current source while watching

TV, press INFO to see the on-screen status display.

ChannelView™ Channel Listings

ChannelView provides listings, as sent by the broadcasters, for memorized channels on ANT 1 or ANT 2. Digital channels are indicated with a “D” and analog channels with an “A.” Digital channels are shown with the major channel and sub-channels (or bitstreams). The analog channel name is displayed if you entered a name in the

Channedl menu.

Note: If limited data is shown or no program data appears, it is because the broadcaster is not sending the information. This is not a defect of your TV.

Selecting from Multiple Sources: The Input

Selection Menu

The Input Selection menu allows you to select an input to watch on the TV. The current input appears as a goldcolored icon.

1. Press INPUT on the TV’s remote control to display the

Input Selection menu (Figure 2).

2. To select a different input, press on the TV’s remote control to move the highlight through icons in the input section.

3. Press ENTER to switch to the device and close the menu.

More About the Input Selection Menu

• To assign meaningful labels to the icons, such as

“VCR” or “DVD,” see the “Input Name” section of chapter 4, “TV Menu Settings.”

• To rearrange the icons, see the “Icon Order” section of chapter 4, “TV Menu Settings.”

• To use with IEEE 1394 devices, see additional information in chapter 7, “Using IEEE 1394 Devices.”

Using ChannelView

Feature

View listings while viewing

ANT 1 or ANT 2.

Scan through memorized channels one by one.

Scan quickly through memorized channels.

View detailed information for digital channels.

Return to viewing basic listings information

Instructions

Press GUIDE.

Press or .

Press PAGE / .

Press or to highlight a channel and press .

Press .

Input Section

Figure 3. ChannelView screen, current programs. Use

to exchange displays for current and future programs.

Figure 2. Input Selection menu

IMPORTANT

To receive ChannelView updates: Set the

Energy Mode to Fast Power On and leave the

TV powered off for a while each day. If the TV loses power, program listings will be lost until the next update.

Figure 4. ChannelView screen, future programs on the selected channel (digital channels only)

Status Display

The on-screen status display appears when you turn on the TV, change inputs, change channels, or press the INFO button on the remote control. The most common displays

Chapter 3. TV Operation 37 are shown below. Seldom or never do all the status indicators appear at the same time.

Analog Program

1. Source Antenna or Input

2. Analog Channel being received (If an antenna source)

3. Channel Name (if or named in the Channel menu)

4. Signal Type Being Received. Possible:

From ANT-1, ANT-2, or INPUT jacks: 480i

From COMPONENT jacks: 480i, 480p, 720p,

1080i

5. Screen Format in use

Possible:

Analog 480i /480p signals: Standard, Expand,

Zoom, Stretch, Stretch Plus, Narrow

720p/1080i signals: Standard, Wide Expand

6. Stereo and/or SAP being broadcast. In Split

Screen mode, the speaker icon is on the right to indicate the sub-picture is the sound source.

7. V-Chip Ratings

1

4

6

7

9

10

12

2 3 11

Ant-1 3 XXXX ANT-1 3

480i Standard 5

Stereo SAP

TV-PG DLSV

FAV2

Monday 11:00 AM

Sleep: 30

8

MUTE

8. Channel is in current FAV bank (FAV bank 2)

9. Day and Time

10. Sleep Timer remaining time

11. Split Screen picture source and channel

12. Audio Mute on

Digital Program

1. Digital Major and Sub-Channel Number

2. Digital Channel Name (only if broadcast)

3. Signal Type Being Received

Possible: SD 4:3, SD 16:9, HD

4. Screen Format in Use

Possible:

SD 4:3: Standard, Expand, Zoom, Stretch, Stretch

Plus, Narrow

SD 16:9 or HD 16:9: Standard, Wide Expand

5. Language(s) being broadcast

6. Program Name (if broadcast)

7. Copy-Protection Status. Possible:

Copy Once: Program can be recorded

Copy Never: Program can never be recorded.

3

5

1 2 6

Ant-1 42-1 XXXXXXX XXXXXXXXXXXXXX

HD Standard 4

English

TV-PG DLSV Copy Never: 3 Days

FAV2

7

Monday 11:00 AM

Sleep: 30

Digital IEEE 1394 Device

1. Status of D-VHS VCR or IEEE 1394 device

2. Counter of D-VHS VCR

3. Special message line (shows only when a special message is needed; may be seen with analog signals)

4. Copy-Protection Status. Possible:

Copy Once: Program can be recorded

Copy No More: Program can never be recorded; program may be moveable.

1

3

DVCR

HD Standard

English

TV-PG DLSV Copy No More

Play 01:20:15

Monday 11:00 AM

Sleep: 30

2

Special Message Line

4

38 Chapter 3. TV Operation

TV Signals and Display Formats

This is a widescreen TV, also known as a 16:9 TV. This shape reflects the new types of images available from

HDTV and many DVDs. There are still many older style narrow-screen images (called 4:3 aspect ratio) you will encounter. While there is no perfect solution for displaying a squarish, narrower image on a wide screen,

Mitsubishi offers several display formats from which you can choose.

Press FORMAT on the TV remote control to cycle through the available display formats. The last-used format for each device is used when you return to that device.

Note:

• Only standard format is available for Split Screen.

• PC formats vary depending on the PC signal.

• For 1080p signals from an HDMI input, see “Computer Display Formats” in chapter 6, “Using the TV with a Personal Computer.”

DVD Definitions

Anamorphic (or Enhanced for WideScreen TV)

These DVDs are recorded in a special way to properly show widescreen images on 16:9 TV sets using the

Standard format mode. This is the recommended viewing choice.

Non-Anamorphic (or 4:3, 1:33:1, Letter Box, or Full

Screen)

These DVDs are recorded for use with traditionally shaped, squarish TVs. They may be full screen (4:3 or

1:33:1) which crops movies to fit the narrow TV, or letter box, which adds black top and bottom bars.

This information may be listed on the DVD case. Some

DVDs support both types of recordings.

Signal Definitions

480i Signals: Traditional analog interlaced signals from or through ANT-1 and 2, INPUT 1–3, COMPONENT

1 and 2, HDMI 1 and 2.

480p Signals: Progressive-scan DVD signals on COM-

PONENT inputs and HDMI 1 and 2 .

720p and 1080i Signals: High-definition signals received through COMPONENT inputs and HDMI 1 and 2.

These signals are always 16:9 (widescreen).

SD 4:3: Standard-definition narrow-screen format signals from digital channels and IEEE 1394 devices.

SD 16:9: Standard-definition widescreen format signals from digital channels and IEEE 1394 devices.

HD: High-definition wide-screen format signals from digital channels and IEEE-1394 devices. These signals are always

16:9 (widescreen).

TV Display Format Definitions

Standard: This is the full-screen format. HDTV signals use this format. This format is useful for displaying

Anamorphic DVDs that have 1.78:1 or 1.85:1 aspect ratios. Anamorphic DVDs that have a 2.35:1 aspect ratio are displayed with black bars at the top and bottom, but show the entire image correctly. Narrow (4:3) images are stretched evenly from side to side. Available for all signals.

Expand: This enlarges the picture to fill the screen, cropping off some of the image at the top and bottom. This is useful for reducing the letter box top and bottom bars of non-anamorphic DVD images. Available for 480i, 480p, and digital SD 4:3 signals only.

Zoom: This enlarges the picture, cropping off some of the image at each side and top and bottom. This is useful for removing or reducing the black top and bottom bars on anamorphic DVDs with a 2.35:1 aspect ratio. Available for 480i, 480p, and SD 4:3 signals only.

Stretch: This format stretches a narrow (4:3) image across the screen; there is less stretch in the center than at the sides, however. This allows the entire narrow image to be displayed across the screen with less distortion than is seen in the Standard format. Available for 480i,

480p, and SD 4:3 signals only.

Stretch Plus: Similar to stretch mode, but to minimize distortions on the side, the picture is expanded to crop off portions of the top and bottom. Except when displaying menus or Split Screen, press to adjust the position of the picture vertically. Available for 480i, 480p, and SD 4:3 signals only.

Narrow: This format displays narrow (4:3) images in their original shape, and adds stationary black side bars to fill the screen. Available for 480i, 480p, and SD 4:3 signals only.

Wide Expand: Enlarges the picture, cropping some of the image on both sides. This Expand format is useful to remove or reduce black side bars added to narrow images that are converted to 16:9 signals for digital broadcast. Available for 1080i, 720p, digital SD 16:9 and digital HD signals.

Note: All high-definition channels send widescreen (16:9) signals, but not all programming sent on these channels was created for this format. As a result, the broadcaster must convert such programming for broadcast, and may stretch the image or add side bars to fill the widescreen area.

TV Display Formats

See descriptions on the preceding page.

���������������

������������������������

����������

��������

����������������������������

������

������������������

����������������

������������������

������������

���������������������������������

����

����������������������

�������������������

����������������������

����������������������������������������

�������

�����������������

���������������

������������������

������������������������������������

������������

������������������

���������������

���������������������

������������������������������������

������

�����������������������������

��������

������������������

�������������������

Chapter 3. TV Operation 39

���������������

��������������

����������

��������

�������������

������

�������������������������

����������������������

������������������������

����������������������������

����

�������������������������

����������������������

�������������������������

�������������������������������������������

�������

�������������������������

����������������������

�������������������������

����������������������������

������������

�������������������������

����������������������

������������������������������

����������������������������

������

������������������������

���������������������

������������������������

����������������������������

�����������

�������������������

���������������������

��������������������

���������������������������������

40 Chapter 3. TV Operation

Split Screen

Split Screen allows you to view pictures from two different sources at the same time. Split Screen is available when you have video sources connected to the TV in addition to a connection to ANT 1 or ANT 2.

Operation

Split Screen Operations

Turn Split Screen on or off

Switch the sound source between main and sub-pictures.

Check which picture is the sound source.

Change the source of the sub-picture.

Instructions

Press SPLIT.

Press or . The speaker icon appears briefly to indicate the sound source as either the main picture (left) or sub-picture

(right). The sound source is the side you can control with the remote control.

Press INFO. The speaker icon appears in the status display to indicate the sound source.

1. Press to make the sub-picture the sound source.

2. Press INPUT and move the highlight to the icon for the input you wish to view as the sub-picture (see figure 5).

3. Press ENTER to make the change.

Grayed-out input icons are unavailable as Split Screen sources or with the current source.

Press to make the sub-picture the sound source then press CH / .

Change channels (when the input source is

ANT 1 or ANT 2).

Freeze or unfreeze the sub-picture.

Change the size of the main and sub-pictures.

Make the sub picture fill the screen.

Press (PAUSE). Press again to return to normal moving video.

Repeatedly press FORMAT to cycle through picture sizes. See the following page for sample displays.

1. Press to make the sub-picture the sound source.

2. Press SPLIT to close Split Screen mode.

“SPLIT” appears under the

Video icon to distinguish this menu from the Input

Selection menu.

Choice of Split Screen sub-Picture Sources

IMPORTANT

Split Screen is unavailable if:

• Your only inputs are ANT 1 and ANT 2.

• Either picture source is a 1080p signal from an HDMI jack.

• Either picture source is from a personal computer.

Figure 5. Change the source of the sub-picture with the

Split Screen Input Selection menu.

Split Screen Displays

16:9 Main Picture/

4:3 Sub-Picture

16:9 Main

Picture

4:3 Sub-

Picture

16:9 Main Picture/

16:9 Sub-Picture

16:9 Main

Picture

16:9 Sub-

Picture

Chapter 3. TV Operation

4:3 Main Picture/

4:3 Sub-Picture

4:3 Main Picture

4:3 Sub-

Picture

4:3 Main Picture/

16:9 Sub-Picture

4:3 Main Picture

16:9 Sub-

Picture

41

16:9 Main

Picture

4:3 Sub-

Picture

16:9 Main

Picture

16:9 Sub-

Picture

4:3 Main Picture

4:3 Sub-

Picture

4:3 Main Picture

16:9 Sub-

Picture

16:9 Main

Picture

4:3 Sub-

Picture

16:9 Main

Picture

16:9 Sub-

Picture

4:3 Main Picture

4:3 Sub-

Picture

4:3 Main Picture

16:9 Sub-

Picture

Display choices. Press the FORMAT key repeatedly while in Split Screen mode to view different displays.

TV Inputs for Split Screen

The available Split Screen picture sources are listed below.

Available as either main picture or subpicture

Available as main picture only

• Analog channels

• Devices on VIDEO/S-VIDEO inputs

• Devices on COMPONENT inputs

• Devices on either HDMI input

• Digital channels received from CableCARD™ or either Antenna input

• IEEE 1394 devices

Sub-

Main

Picture

ANT 1

ANT 1

(analog only)

ANT 2

(analog only)

INPUT COMPONENT

HDMI 1

(no 1080p)

ANT 2

INPUT

COMPONENT

HDMI 1 (no 1080p)

*

**

HDMI 2 (no 1080p)

IEEE 1394

PC-DVI

* Only when main picture and sub-picture are from different INPUT jacks

** Only when main picture and sub-picture are from different COMPONENT jacks

HDMI 2

(no 1080p)

Combinations of picture sources you can view with Split Screen. Check marks indicate available combinations.

4

TV Menu Settings

3D Graphical Menu System

. . . . . . . . . . . . . . . . . . . . .

44

Main Menu

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

45

Setup Menu

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

46

Input Name Menu

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

48

Icon Order Menu

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

48

Channel Menu

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

49

Captions Menu

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

51

Parental Lock Menu

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

53

Setting a Pass Code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

Lock TV by Time and Front-Panel Lock . . . . . . . . . . . . . . . . . . . . . . 53

Rating Menus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

Bypassing the Ratings Lock and Lock by Time . . . . . . . . . . . . . . . . . 55

V-Chip Signal Information

TV Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56

Movie Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56

Audio/Video Menu

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

57

Audio Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

Video Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

44 Chapter 4. TV Menu Settings

3D Graphical Menu System

Your TV has Mitsubishi’s exclusive 3D Graphical on-screen operating system, which provides on-screen information for menu choices and changes using the TV’s remote control.

Menu Screens

A picture (icon) is highlighted on the menu screen when selected with the directional arrows . You may then make changes within the menu or access submenus, if available.

You can also open sub-menus from a button. Sometimes when you select a button, an automatic function begins.

The tures:

system includes the following special fea-

• The currently selected icon or button is highlighted with a yellow outline; the text color is yellow.

• On-screen instructions, shown in the message line at the bottom of the menu, provide feature selection and adjustment information.

• Some on-screen menu options must be set before other options are available.

7

6

3 5

4

3

4

1

2

Remote Control Buttons

The following buttons on the remote control help you navigate within the

system:

Key

1 MENU

2 EXIT

3

(Adjust Left/Right Keys)

4

(Adjust Up/Down Keys)

5 ENTER

6 Numbers, Letters

7 CANCEL

Function

Display or close the Main menu or move back one menu screen at a time.

Close all menus and return to TV viewing.

to select a menu item to change.

• to change the settings.

• to scroll through pre-set text-box entries.

Open a menu, start an automatic function, or select a check box.

Enter custom names in some text boxes.

Clear a setting or stop an automatic function.

Chapter 4. TV Menu Settings

Main Menu

Press MENU on the remote control to open the Main menu, figure 1. See below for an overview of the options available through the Main menu.

Figure 1. Main menu.

45

Setup

Select English or Spanish for menus and on-screen displays.

Memorize the available channels for the antenna or cable service connected to the

ANT 1 and ANT 2 jacks.

Set the TV’s internal clock either manually or have the TV set the clock automatically.

Set the TV Timer to turn on the TV automatically at a designated time.

• Set the energy mode for power consumption when the TV is powered off.

• Turn off Demo Mode.

View the TV’s software version.

Input Name

Assign useful names to TV inputs so that you can easily find them in the Input Selection menu.

Icon Order

Rearrange icons in the Input Selection menu to put frequently used icons first.

Channel

Edit channels for the ANT 1 and ANT 2 inputs.

Manually add or delete channels from memory, name analog channels, or add your favorite channels to a FAV (Favorites) list.

View signal strength of a currently tuned digital channel.

Captions

Display closed captions (if sent by the broadcaster).

Select settings for analog or digital captions.

Parental Lock

Block or allow programming based on rating signals sent by the broadcast station.

Lock the TV by time.

Lock the front-panel buttons.

Audio/Video

Reset a selected input’s A/V memory to the original factory settings.

Customize individual audio and video settings.

Display a blue screen when viewing a device with no video signal or a poor video signal.

Enable/disable Film Mode.

Turn the TV speakers on or off.

46 Chapter 4. TV Menu Settings

Setup Menu

channels from memory, naming channels, and saving favorite channels in custom memory banks.

Note: If using a CableCARD™, the complete list of available channels is provided through the

CableCARD and the ANT 1 option is grayed out.

Clock (Setup Menu)

Set the clock if you wish to use the TV’s Timer function or schedule delayed recordings. You can use either the manual or auto method to set the clock.

Figure 2. Setup menu

Language (Setup Menu)

Choose to display the on-screen menus in either English or Spanish (Español).

To listen to audio in other languages (when available), see the “Audio Settings” section in this chapter and refer to

“SAP” (analog signal) or “Language” (digital signal).

Memorize Channels (Setup Menu)

For ANT 1/MAIN and ANT 2/AUX

The memorization process performs two scans of all possible channels on the selected ANT input. Analog channels are scanned first, then the process is repeated for digital channels. Channel memorization may take up to 15 minutes to complete.

To start channel memorization

1. Highlight an input selection based on your connections:

Input

Ant 1 Air,

Ant 2 Air

Ant 1 Cable,

Ant 2 Cable

Condition

When connected to an indoor/outdoor antenna

When connected to direct cable (no cable box)

2. Press ENTER to start automatic channel memorization.

To stop channel memorization before completion

Press CANCEL.

Channels memorized before you pressed CANCEL are retained in memory. If you restart memorization, all previously memorized channels for the selected antenna input are erased and the process starts over from the beginning.

After channel memorization, press CH / to tune to memorized channels. Select the Channel menu for further channel editing, such as adding and deleting

Figure 3. Clock submenu

Setting the Clock Manually

Time

With the hour highlighted in yellow characters, press repeatedly to slowly increment the hour and associated

AM/PM indicator or press and hold to quickly increment the hour. Press ENTER to highlight the minutes in yellow.

Press to set the minutes.

Date

With the month highlighted in yellow characters, press

to select the correct month. Press ENTER to highlight the day. Press to select the correct day. Press ENTER to highlight the year. Press to select the current year.

Time Zone

Select your correct time zone. Press or to select the time zone for your area ( Atlantic, Eastern, Central,

Mountain, Pacific, Alaska or Hawaii). Press to move to the Daylight Savings option.

Daylight Savings

Press or to select either Applies or Ignore, depending on whether or not daylight savings time is used in your area.

Note: If Clock Setting is set to Manual, each time the time change occurs, you must open this menu and set the

TV’s clock ahead or back.

If you have selected Auto for Clock Setting, the TV’s clock adjusts automatically to daylight savings time.

Chapter 4. TV Menu Settings 47

Setup Menu, continued

Setting the Clock Automatically

Select the Time Zone and the Daylight Savings (DST) options for your state. Press to select Applies or

Ignore. You may then tune to a channel on ANT 1 or

ANT 2 that uses Extended Data Service (XDS) time data, typically a PBS channel. With Auto selected, the TV automatically retrieves the correct time and date information from this channel.

Be aware that if a channel displays incorrect time information, it is because of information sent from the broadcaster and is not a defect of the TV.

Note: You may find that some channels send the incorrect time and the TV clock is reset every time you tune to those channels. To prevent unwanted clock resets, first use the Auto method to set the clock from a channel sending the correct time, then change the method to Manual.

Set Time

With the hour highlighted in yellow characters, press repeatedly to slowly increment the hour and associated

AM/PM indicator or press and hold to quickly increment the hour. Press ENTER to highlight the minutes. Press to set the minutes.

Device

Press or to select the device to use when the Timer turns on the TV. If the TV is already on at the selected time, the Timer will switch the TV to this device.

Channel

When the selected device is an antenna, you can select a channel for the TV to tune to when it comes on. Highlight the Channel box and

• press CH / or to choose from memorized channels.

• Enter a channel number from the remote control. You can also enter sub-channel numbers for digital channels.

Timer (Setup Menu)

Figure 4. Timer submenu

The Timer feature allows you to set a day and time for the

TV to turn on automatically and the device and channel to display when it switches on. If the TV is already on at the requested time, the TV automatically tunes to the channel you designated in the Timer menu.

When the Timer turns on the TV, the following message is displayed: “Press a button for the TV to stay on.” Press any button on the remote control within five minutes if you wish the TV to remain on.

Note: The TV clock must be set before you can use the

Timer feature (see preceding page to set the clock).

On/Off

Press to enable or disable the Timer.

Set Day

Select the day or days that the TV will turn on automatically. Press or to select Daily, Mon-Fri (Monday through Friday), or individual days of the week.

Energy Mode (Setup Menu)

The Energy Mode option lets you select the TV’s level of power consumption while the TV is turned off. Choose either Low Power or Fast Power On. The Low Power setting uses less energy, but TV power-on takes longer.

The default is Fast Power On. Keep this setting at Fast

Power On if you:

• Need faster power on.

• Wish to turn off the TV while recording to an IEEE

1394 device.

• Wish to schedule future IEEE 1394 recordings for a time when the TV will be off.

• Expect to use the TV Timer function to turn on the

TV at a preselected time.

• Need the TV Clock to remain accurate for the TV

Timer and for scheduling recordings. With the

Low Power setting, you must reset the TV Clock if the TV is left turned off for over 48 hours.

• Wish to receive updates to the ChannelView™ channel listings.

Note: CableCARD™ requires the Fast Power On setting.

If you insert a CableCARD™, the TV will automatically override a Low Power setting and change to the Fast Power On setting.

Demo Mode Off (Setup Menu)

Some TVs are shipped from the factory with Demo Mode active for use in retail stores. If Demo Mode is active, highlight the Demo Mode Off button and press ENTER.

Software Version (Setup Menu)

For servicing purposes it may be necessary to know the software version in your TV. This information is displayed at the right side of the Setup menu screen.

48 Chapter 4. TV Menu Settings

Input Name Menu

Use the Input Name menu to assign useful labels to the

TV inputs that appear in the Input Selection menu. The current viewing device and any unused inputs appear grayed out and unselectable.

Use the PC DVI option to specify the type of video signal coming from your computer, either Analog or Digital. For more about this option, see chapter 6, “Using the TV with a Personal Computer.”

To Remove the Icon for an HDMI Device

When you disconnect an HDMI device, the icon remains in the Input Selection menu until you choose to remove it.

1. In the Input Name menu (see figure 5), highlight the box for the disconnected HDMI input.

2. Press to select Off.

3. Press EXIT to close all menus.

Icon Order Menu

The Icon Order menu allows you to rearrange the device icons that appear in the Input Selection menu. Change the sequence to put frequently used icons at the start of the list.

To change the icon order

1. Press to highlight the icon to be moved and then press ENTER.

2. Press to drag the icon to the desired position. Press ENTER to set the new position.

Detected Inputs that Can

Be Renamed

Figure 5. Input Name menu

Type of Video Signal from

Personal Computer

To rename an input

1. If you are currently watching the input you wish to rename, change to another input. To do so, press INPUT to open the Input Selection menu, highlight a different input, and press ENTER.

2. With the Input Name menu displayed, press to move the highlight to the box for the input you wish to rename.

3. Press to select from the following list.

Cable Box

Camcorder

Game

HD Disc

DVD

DVD2

Satellite

VCR

DVR (digital video recorder, recordable

DVD)

Only one VCR label is available, so If you have a second VCR connected, leave the name as the default name.

Figure 6. Icon Order menu

IMPORTANT

It is possible to use the same name for more than one input. To avoid confusion, be sure to use different names for each input.

Chapter 4. TV Menu Settings 49

Channel Menu

Press CH / to review the channels in memory. Press

to select Added or Deleted for the channel shown in the Channel box.

To Add a New Digital Channel

1. In the channel menu, enter the physical channel number in the Channel box, including the sub-channel number

(press

If no sub-channel is specified, press

2. Press ENTER to tune to the channel.

3. Highlight the Added radio button to add the channel to memory.

Settings for the Channel

Number Shown

Figure 7. Channel menu

FAV Memory

Banks

Antenna (Channel Menu)

Select either 1 (ANT 1 MAIN) or 2 (ANT 2 AUX) as the antenna source for the channels you wish to edit.

Channel (Channel Menu)

Select the affected channel number (shown in the

Channel box) in any of three ways:

• Press CH / to select from channels already in memory. If you also wish to tune to the channel, press ENTER.

• Highlight the channel box and press to move through all channel numbers, one at a time. If you also wish to tune to the channel, press ENTER.

• Highlight the channel box, enter the number directly, and press ENTER. Note that with this method, you must press ENTER for the screen to display settings for the selected channel.

Channel numbers can be one part, analog or digital (up to five digits long), or two part for digital channels. For a twopart digital channel, press CANCEL on the remote to enter a separator after the first, second, or third number, depending on the broadcaster’s channel information.

For digital channels, when the broadcaster has sent a virtual channel number, the virtual channel number is shown in the text box and the original physical digital channel is shown below on screen as a reference. One original channel number can be associated with several different virtual channels.

Memory (Channel Menu)

Signal-Strength

(digital channels only)

After the available channels have been memorized with

Memorize Channels on the Setup menu, you can add weaker channels or delete unwanted channels using this option. For example, if you wish to see only digital channels listed, use this menu to delete analog channels from memory.

Name

Analog channels from ANT 1 and ANT 2 can be named with up to four characters. The name you enter here will appear on the TV screen as part of the on-screen status display. Digital channels may already be named if the broadcaster sends the information.

1. Press a number key repeatedly to cycle through the characters associated with the key. You can also use

to change a highlighted character.

2. Press ENTER to set the letter and move to the next letter position. Press CANCEL to move back one position.

Signal Strength (Channel Menu)

Displays the approximate signal strength of the currently tuned digital channel. Use this indicator to help you adjust the antenna direction for best signal reception.

The taller the bar, the stronger the signal. This indicator applies only to digital channels.

To view the effects of antenna adjustments on digital channels, tune to the digital channel you wish to measure while remaining in this menu. To tune to a channel, either:

• Highlight the channel box, press CH / or to display the desired channel number, and press ENTER.

• Enter the channel number on the remote control and press ENTER.

Terminology

Virtual Channel Number

A channel number used by a local broadcaster to help you identify their digital channel. Usually this is associated with their traditional analog channel number. For example, a broadcaster may associate digital channel 2-1 with analog channel 2.

Physical Digital Channel Number

The channel number officially assigned to the actual broadcast frequency.

50 Chapter 4. TV Menu Settings

Channel Menu, continued

FAV (Channel Menu)

The FAV feature lets you store groups of favorite channels in up to nine different FAV memory banks. For example, each household member can store favorite channels in their own bank or you can store groups of channels by content, e.g., news, sports, children’s programming, etc.

You can store the same channel in multiple FAV banks.

Once you have added a channel to FAV memory, FAV and the memory bank number appear under the tuned channel number on the TV screen. You can access the

FAV feature through the Channel menu or you can bypass the menu and use only the remote control.

FAV Setup Using the Channel Menu

Initial Setup of a FAV Bank and

Adding FAV Channels Using the

Menu

Removing FAV Channels Using the

Menu

1. With the Channel menu displayed, select a channel using one of the methods described on the preceding page, for example, press CH / for a memorized channel.

2. Highlight the desired bank ( FAV1–FAV9) and press ENTER to check mark the selected FAV memory bank. The channel number displayed has now been added to the checked FAV bank.

3. With the FAV bank still highlighted, press CH / to display the next channel you wish to add to the FAV bank.

4. Press ENTER to add a check mark next to the highlighted FAV bank.

5. Repeat steps 2–4 for additional channels and FAV banks.

1. With the Channel menu displayed, press CH / to display the memorized channel you wish to remove.

2. Highlight the desired FAV memory bank ( FAV1–FAV9).

3. Press ENTER to remove the check mark.

Using FAV Channels

Viewing FAV Banks

Changing FAV Banks

If No FAV Banks Are Set Up

1. Press the FAV key. Wait for the TV to tune to a channel in the current FAV bank.

2. Press the FAV key repeatedly to cycle through the channels available in the current FAV bank.

1. Press the FAV key. Wait for the TV to tune to a channel in the current FAV bank.

2. When tuning is complete and while the TV status display is still visible on screen, press the number key for the desired bank.

Note: Wait for the channel change to finish before pressing the number key.

Otherwise, the TV may ignore the FAV number.

The FAV key switches to the previously tuned channel; works like the QV key.

FAV Setup Using Only the Remote Control

Adding FAV Channels 1. While watching TV, tune to the channel you want to add to the current FAV memory bank. See the instructions above if you need to first change to a different FAV bank.

Removing FAV Channels

This procedure removes the channel only from the selected bank and leaves the other banks unchanged.

2. Press and hold the FAV button for about 2 seconds. When FAV and the memory bank number appear under the channel number, the channel has been successfully added.

1. While watching TV, press the FAV button

2. While the TV status display is still visible on screen, press the number key for the memory bank.

2. Press the FAV button repeatedly until you see the desired channel.

3. While the channel number and FAV indicator (with correct bank number) are still displayed on the screen, press CANCEL. You must press CANCEL before the indicator disappears. When the FAV indicator disappears, the channel has been successfully removed.

Chapter 4. TV Menu Settings 51

Captions Menu

For analog channels, broadcasters can send either standard closed captions or text service. Standard closed captions follow the dialogue of the characters on screen and display in a small section of the screen. Text-service closed captions often contain information such as weather or news and cover a large portion of the screen.

For digital channels, broadcasters can send up to six different captioning selections or can send analog captions that are the same as those sent by the analog station.

Each TV station may broadcast only one or two types of captions or none at all. The TV cannot decode closed captions received on component or HDMI inputs.

Figure 8. Captions menu

Digital Captions

The following display options are available for digital sources:

• Captions 1–6: Sent by broadcaster.

• On if Mute: Closed captions are displayed when audio is muted. When selected, press MUTE on the TV remote control to turn captioning on/off (Caption 1).

• Off: No closed captions.

Note: For digital programs, if the broadcaster is sending only analog captions converted to digital format, then the analog caption settings apply.

Appearance

The closed-captions provider selects the default options when sending digital closed captions. Select Custom to override defaults and customize the appearance of closed captions. These settings do not apply to analog closed captioning converted to digital.

Digital Settings

The Digital Settings menu allows you to customize the appearance of the closed captions sent by the broadcaster. Digital settings do not apply to analog closed captions converted to digital.

To open the Digital Settings menu, select Custom for the

Appearance option. Move the highlight to the Digital

Settings icon and press ENTER.

Analog Captions

The TV can display one of the following captions for analog sources:

• CC1, CC2, CC3, or CC4: standard closed-caption signals

• Text1, Text2, Text3, or Text4: Text-service signals

• On if mute: Closed captions appear when audio is muted. When selected, press MUTE on the TV remote control to turn on/off the standard closed-caption signal CC1.

• Off: No closed captions.

Background

To make the analog closed captions easier to read, you can choose to display the background color as either black or gray behind the text.

IMPORTANT

When analog text closed captioning is selected, a large black or gray box appears on your TV screen if no signal is broadcast.

Figure 9. Closed Captions, Digital Settings sub-menu

Font

The available font options are as follows:

• Default: Selected by the closed-captions provider

• Font 1: Monospaced font with serifs

• Font 2: Proportionally spaced font with serifs

• Font 3: Monospaced font without serifs

• Font 4: Proportionally spaced without serifs

• Font 5: Casual font

• Font 6: Cursive font

• Font 7: Small capitals

52 Chapter 4. TV Menu Settings

Captions Menu, continued

Size

Select the desired font size. Large is the recommended font size.

Color

The available font colors are listed below. Text and background cannot be set to the same color.

White

Black

Magenta

Red

Yellow

Green

Cyan

Blue

Background

You can change the background color to make the digital closed captions easier to read. The available background colors are listed below. Text and background cannot be set to the same color.

White

Black

Magenta

Red

Yellow

Green

Cyan

Blue

Opacity (Font)

You can customize the visibility of your fonts using the following settings:

• Translucent: TV program is dimmed behind the text

• Transparent: Invisible text reveals the TV program behind.

• Opaque: Solid text blocks view of the TV program

• Flashing: Text flashes at intervals

Background Opacity

You can customize the background for digital captions using the following settings:

• Translucent: TV program is dimmed behind the background

• Transparent: No visible background

• Opaque: Solid background covers TV program

• Flashing: Background flashes at intervals

IMPORTANT

Mitsubishi recommends you use contrasting colors for captions and background.

Black translucent background combined with a white font makes an easy-to-read combination.

Use care when selecting custom colors. Your choice may affect the readability of captions.

IMPORTANT

The content of captions is determined by the broadcaster. If your captions show strange characters, misspellings, or odd grammar, it is not a malfunction of the TV.

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

advertisement