INCITE 9I AND 11I
Setting the 9i and 11i is done by pushing the three buttons in a specific sequence. The button on the side of the computer is the Set button. The two buttons on the bottom are the left and right Mode buttons. If the Mode button is called out in the directions without specifying which one, you may push either one and the computer will accordingly scroll in a different direction.
6
To set Units (distance and temperature)
This setting tells the computer which conversion to use: metric or SAE (“English”)
1. Cycle Mode to Max.
2. Hold Set.
3. Cycle Mode to your preferred setting (MPH for miles or KPH for kilometers).
4. Push Set to select.
The computer displays the temperature icons.
5. Cycle Mode to your preferred setting (F for Fahrenheit, C for Celsius).
6. Push Set to select.
The computer returns to the current speed display.
To set Odometer
By default, the odometer always starts at ‘0’. If desired, the odometer can be manually set at another value.
1. Cycle Mode to ODO.
2. Hold Set.
The computer displays the bottom row of digits with the first digit flashing.
3. Cycle Mode to your preferred value.
4. Press Set to select.
The next digit flashes.
5. Repeat steps 3 and 4 until all digits have been selected.
After the last digit is selected, the computer returns to the current speed display.
To set Clock
The clock can be set to 12 hours or 24 hours. When setting your hours value, choose accordingly. You will set the 12 or 24 hour selection after setting the values.
1. Cycle Mode to CLK.
2. Hold Set.
The computer displays the clock, with hours flashing.
3. Cycle Mode to your preferred value.
4. Push Set to select.
5. Cycle Mode to your preferred value for minutes.
6. Push Set to select.
7. Cycle Mode to your preferred value for hours format (12 or 24).
8. Push Set to select.
After the hours format is selected, the computer returns to the current speed display.
Figure 13- Wheel selection icons
Wheel sizes
The 9i and 11i allow you to program the computer to calculate using two different wheel sizes. The second wheel size allows the computer to calculate using the wheel size of a second bike. For example, you can use the computer on your road bike with 700c racing wheels, then move it to your mountain bike with 26” wheels. In both cases, the trip distance and speed will be accurate. The computer adds the data for the two wheel sizes resulting in the total distance (ODO). In performing these steps, note that the wheel icon in the upper left corner has two values: Wheel 1 is a circle (Figure 13) and Wheel
2 is a circle with a semi-circle surrounding it.
To set the wheel size
1. Cycle Mode to TME.
2. Hold Set.
The wheel selection icon appears in the upper left corner.
3. Cycle Set to your preferred wheel.
4. Cycle Mode to your preferred wheel size.
For a custom wheel size, see To set a custom wheel size
5. Hold Set to select.
The computer returns to the current speed display.
To set the second wheel size, repeat the instructions, but choose the other wheel icon before setting values.
Setting the computer
To set a custom wheel size
1. Cycle Mode to TME.
2. Hold Set.
The wheel selection icon appears in the upper left corner.
3. Cycle Set to your preferred wheel.
4. Cycle Mode to the four-digit number.
5. Press Set.
6. Cycle Mode to your preferred first digit value (see Table 3).
Table 3- Wheel size and corresponding settings in millimeters
700 x 20 2086 26 x 1.5
2010
700 x 23
700 x 25
700 x 28
2096
2105
2136
26 x 1.90
2045
26 x 1.95
2050
26 x 2.0
2055
700 x 32
700 x 35
700 x 38
2155
2168
2180
26 x 2.1
2068
26 x 2.2
2075
Custom 0000 - 2999
7. Press Set to select.
8. Repeat steps 6 and 7 for each following digit.
9. Hold Set.
The computer returns to current speed display.
To select the wheel size
1. Cycle Mode to TRP.
2. Hold both left Mode and right Mode at the same time.
The wheel icon changes, indicating the wheel selection has changed. Repeat step 2 to change to the other wheel size.
To restart the trip modes
The trip modes include TRP, AVG, TME, and MAX. This operation sets all four values to zero, allowing the computer to display information for a single ride.
1. Cycle Mode to MAX.
2. Hold Set, and do not let up until after completion of step 3.
3. Hold Mode.
The Max setting restarts at ʻ0ʼ.
Setting the computer
7
