INSTALLATION REQUIREMENTS. KitchenAid KOWT107EBS, KOWT100ESS, KOWT107ESS, KOWT104ESS, KOWT100EBS


Add to My manuals
16 Pages

advertisement

INSTALLATION REQUIREMENTS. KitchenAid KOWT107EBS, KOWT100ESS, KOWT107ESS, KOWT104ESS, KOWT100EBS | Manualzz

INSTALLATION REQUIREMENTS

Tools and Parts

Gather the required tools and parts before starting installation.

Read and follow the instructions provided with any tools listed here.

Tools Needed

■ Phillips screwdriver

■ Flat-blade screwdriver

Measuring tape

Level

Drill

1

³⁄₈" (3.5 cm) hole saw

Parts Supplied

■ Two #8–18 x

¹⁄₂" screws

■ Lens (for panel ready models)

Check local codes. Check existing electrical supply. See

“Electrical Requirements.”

It is recommended that all electrical connections be made by a licensed, qualified electrical installer.

Location Requirements

IMPORTANT: Observe all governing codes and ordinances.

■ Cutout dimensions that are shown must be used. Given dimensions provide minimum clearance with warming drawer.

Recessed installation area must provide complete enclosure around the recessed portion of the warming drawer.

Grounded electrical supply is required. See “Electrical

Requirements” section.

Electrical supply outlet should be located in the rear wall on the upper right-hand side of the cutout or in an adjacent cabinet. The outlet must be recessed. If the electrical outlet is located in an adjacent cabinet, a 1 ³⁄₈" (3.5 cm) minimum diameter hole should have been drilled in the back of the cutout or support surface to pass the power supply cord through to the outlet.

Warming drawer support surface must be solid, level and flush with bottom of cabinet cutout.

Warming drawers with oiled bronze, black glass, and white glass panels are approved for indoor use only.

Support surface must be solid, level, and flush with the bottom of the cabinet cutout.

■ 24" (61 cm) minimum cabinet depth.

For best performance results make sure the warming drawer is leveled before completing installation. There is no way to level the warming drawer after it has been installed. If the installation is not level, the door may slide open or not seal tightly, allowing heat to escape.

NOTE: If installing the warming drawer below another product, refer to that product’s literature for any installation requirements.

Product Dimensions

B

A

C

E

WARMING

DRAWER

SIZE

24"

(61 cm)

27"

(68.6 cm)

30"

(76.2 cm)

OVEN

DEPTH (A)

23 ¹⁄₈"

(58.7 cm)

23 ¹⁄₈"

(58.7 cm)

23 ¹⁄₈"

(58.7 cm)

D

RECESSED

WIDTH (B)

22 ¹⁄₄"

(56.5 cm)

25 ¹⁄₄"

(64.1 cm)

28 ¹⁄₄"

(71.8 cm)

RECESSED

HEIGHT (C)

9"

(22.9 cm)

9"

(22.9 cm)

9"

(22.9 cm)

OVERALL

WIDTH (D)

23 ³⁄₄"

(60.3 cm)

26 ³⁄₄"

(67.9 cm)

29 ³⁄₄"

(75.6 cm)

DRAWER

FRONT

HEIGHT (E)

10 ¹⁄₄"

(26.1 cm)

10 ¹⁄₄"

(26.1 cm)

10 ¹⁄₄"

(26.1 cm)

3

Clearance Dimensions

Front view

120 volt g rounded outlet

(or located in adjacent cabinet)

Warmin g drawer cutout s

Toe kick

A

B

A

B

C

D

E

WARMING

DRAWER SIZE

24" (61 cm)

27" (68.6 cm)

30" (76.2 cm)

MINIMUM

BETWEEN

CUTOUTS (A)

2 ¹⁄₂" (6.4 cm)

2

2

¹⁄₂" (6.4 cm)

¹⁄₂" (6.4 cm)

CUTOUT

HEIGHT (B)

Warming drawer can be installed as an indoor single or double installation or installed under a single oven. Two warming drawers under a single oven are shown.

NOTE: The warming drawer cannot be leveled after being installed.

For outdoor installation, follow the cutout dimensions above.

Install the outdoor warming drawer in a permanent fixture.

MINIMUM/

RECOMMENDED (C)

9 ¹⁄₈" (23.2 cm) 1" (2.5 cm)/

4 ¹⁄₄" (10.8 cm)

9 ¹⁄₈" (23.2 cm) 1" (2.5 cm)/

4 ¹⁄₄" (10.8 cm)

9 ¹⁄₈" (23.2 cm) 1" (2.5 cm)/

4 ¹⁄₄" (10.8 cm)

CUTOUT

WIDTH (D)

MINIMUM

CABINET

WIDTH (E)

22 ¹⁄₂" (57.1 cm) 24" (61 cm)

25 ¹⁄₂" (64.8 cm) 27" (68.6 cm)

28 ¹⁄₂" (72.4 cm) 30" (76.2 cm)

Custom Wood Drawer Front

If you plan to install a custom wood panel to match your cabinets, we recommend consulting a qualified cabinetmaker or carpenter. The back of the wood panel must be sealed to avoid moisture damage.

4

Clearance Dimensions - Flush Installation

Front View

S ide View

F

Top View

A

1

" (25 mm)

S ide Cleat s*

⁷⁄₈” (22 mm)

Platform * e C

B

D

E

S ide Cleat *

1 ⁵⁄₈ " (4.1 cm)

F

E

F

Width of opening (minimum)

Depth of cutout (minimum)

27" Models

A

B

Width of flush inset cutout (minimum)

Height between cutouts (minimum)

27 ¹⁄₄" (69.2 cm)

2

¹⁄₂" (6.4 cm)

C

D

Height of flush inset cutout (minimum) 10 ³⁄₄" (27.3 cm)

Bottom of cutout to floor (recommended) 8 ¹⁄₄" (21.0 cm)

Bottom of cutout to floor (minimum) 5" (12.7 cm)

25

¹⁄₄" (64.1 cm)

25 ³⁄₈" (64.5 cm) e Recommended outlet location

Flush Installation Requirements

A 25 ³⁄₈" (64.5 cm) minimum cutout depth is required.

These dimensions will result in a

¹⁄₄" (6 mm) reveal on all sides of the warming drawer.

The front face of the cleats and platforms will be visible and should be treated as a finished surface.

30" Models

30 ¹⁄₄" (76.8 cm)

2

¹⁄₂" (6.4 cm)

10 ³⁄₄" (27.3 cm)

8 ¹⁄₄" (21.0 cm)

5" (12.7 cm)

28

¹⁄₄" (71.8 cm)

25 ³⁄₈" (64.5 cm)

Cabinet

Back

5

advertisement

Related manuals