Complete Installation. KitchenAid KOWT107EBS, KOWT100ESS, KOWT107ESS, KOWT104ESS, KOWT100EBS


Add to My manuals
16 Pages

advertisement

Complete Installation. KitchenAid KOWT107EBS, KOWT100ESS, KOWT107ESS, KOWT104ESS, KOWT100EBS | Manualzz

7. Use the two #8-18 x ¹⁄₂" screws provided to secure the warming drawer frame to the cabinet.

A

A. Two #8–18 x

¹⁄₂

" screws

Complete Installation

1. Check that all parts are now installed. If there is an extra part, go back through the steps to see which step was skipped.

2. Check that you have all of your tools.

3. Dispose of/recycle all packaging materials.

4. For warming drawer use and cleaning, read the Use and Care

Guide.

5. Push in and turn the control knob to HI, and the light should illuminate.

If warming drawer(s) does not operate, check the following:

■ Household fuse is intact and tight; or circuit breaker has not tripped.

■ Warming drawer is plugged in, and electrical supply is connected.

If you need Assistance or Service:

Please reference the “Assistance or Service” section of the Use and Care Guide or contact the dealer from whom you purchased your warming drawer.

CUSTOM DRAWER FRONT INSTALLATION INSTRUCTIONS

FOR WARMING DRAWERS

Tools and Parts

Gather the required tools and parts before starting installation.

Read and follow the instructions provided with any tools listed here.

Tools Needed

■ Phillips screwdriver

■ Drill and appropriate bits

Parts Supplied

■ 6 - #8-18 x ¹⁄₂" screws

■ Indicator light lens

Parts Needed

■ Custom drawer front

■ Custom handle (optional)

■ Adhesive recommended for plastic to wood

Install Custom Drawer Front Panel

The warming drawer has an interface that will allow a modest range of panel sizes. The actual panel size should be selected by the customer and the contractor to suit the desired effect. It is recommended that a qualified carpenter make and install the custom drawer front and handle(s) to match surrounding cabinetry.

1. Install warming drawer unit as instructed by the installation instructions provided with the warming drawer.

2. Create the custom drawer front. Below are the minimum and maximum dimensions for the custom drawer front. The size of the custom drawer front for the warming drawer will vary according to the specific installation. The depth of the panel will vary in order to have the custom warming drawer flush with the surrounding cabinets.

A

⁵⁄₁₆ " (7.9 mm) dia. hole for indicator light lens (provided in this kit). Locate lens directly in front of indicator light.

B

Model

24" (61 cm)

Warming Drawer

27" (68.6 cm)

Warming Drawer

30" (76.2 cm)

Warming Drawer

A - MAX B - MAX A - MIN B - MIN

23 ³⁄₄"

(60.3 cm)

10 ⁵⁄₁₆"

(26.2 cm)

23"

(58.4 cm)

9 ¹⁄₁₆"

(23.0 cm)

26

³⁄₄"

(67.9 cm)

29 ³⁄₄"

(75.6 cm)

10

10

⁵⁄₁₆"

(26.2 cm)

⁵⁄₁₆"

(26.2 cm)

26"

(66.1 cm)

29"

(73.7 cm)

9

¹⁄₁₆"

(23.0 cm)

9 ¹⁄₁₆"

(23.0 cm)

7

3. It is recommended that if a wood or porous custom drawer front is installed, a high quality spar polyurethane finish be applied to the inner wood surface.

4. For the lens, drill a ⁵⁄₁₆" (7.9 mm) diameter hole through the appearance side of the custom drawer front. This hole will allow the indicator “ON” light to be visible through the custom drawer front. To secure the lens, use an adhesive specified for plastic to wood application.

5. Install custom handle (not supplied) through custom drawer front.

6. The custom drawer front is fastened to the stainless steel drawer by driving 6 screws through clearance holes in the drawer front into the wooden or other custom made panel.

A

C

D

B

E

A. Optional handle

B. Custom door panel

C. Warming drawer front

D. 6 - #8-18 x

¹⁄₂

" screws

E. Lens

D

8

advertisement

Related manuals