The fireplace can be installed with

3 options:

1. Wall hanging to the wall with provided mounting bracket.

2. Stand with the pedestal base.

3. Built in construction.

Follow installation instructions below based on installation preference.

Option 1

Wall Hanging....page 9

Option 2

Pedestal Base....page 12

Option 3

Built in construction....page 13

8

HOMEDEPOT.COM/HOMEDECORATORS

Please contact 1-800-986-3460 for further assistance.

WALL HANGING TO THE WALL WITH PROVIDED MOUNTING BRACKET

Your new electric fireplace may be installed virtually anywhere in your home. However, when choosing a location be sure to follow the general instructions included. For best results install out of direct sunlight. Power supply service must be either completed or placed within the electric fireplace prior to finishing to avoid reconstruction.

Min. 5 CM

2 Inch

Min. 5 CM

2 Inch

Min. 5 CM

2 Inch

WARNING: Keep drapery and other furnishings at least 3 ft / 1 m from the front and sides of the electric fireplace.

Clearance to combustibles

Sides 2 in. / 5 cm

Floor

Top

Back

2 in. / 5 cm

2 in. / 5 cm

0 in. / 0 cm

9

HOMEDEPOT.COM/HOMEDECORATORS

Please contact 1-800-986-3460 for further assistance.

1

Removing the Mounting Bracket

2

Choosing a Wall Location

Remove the Mounting Bracket (A) from the back of the Choose a wall location to attach the Mounting

Bracket (A). Position the Mounting Bracket (A) Fireplace (B) by removing the two pre-attached Screws in the desired location. (CC) at the top back of the unit.

Use a level to align the bracket and mark the four holes with a pencil.

CC

B

A

3

Drilling the Holes

Drill four 1/4-inch (6 mm) holes in the wall.

Insert the Wall Anchors (BB) into the holes using a hammer.

BB

A

10

HOMEDEPOT.COM/HOMEDECORATORS

Please contact 1-800-986-3460 for further assistance.

Operation

4

Attaching the Mounting Bracket

5

Hanging the Fireplace

Attach the Mounting Bracket (A) to the wall by fastening Hang the Fireplace (B) on the hooks at the bottom of the Mounting Bracket (A) and push the Fireplace (B) the four Anchor Screws (AA) into the wall anchors.

into the Mounting Bracket (A).

Re-fasten the two screws removed in Step 1.

A

A

B

AA

6

Hanging the Front Frame

Hang the Front Frame (C) on the Fireplace (B) and gently push on the lower part of the frame until it snaps into place.

7

Securing the Front Frame

Secure the top frame hooks with the two retaining

Screws (CC).

Continue to the fuel bed setup instructions (Page 18).

C

CC

B

11

HOMEDEPOT.COM/HOMEDECORATORS

Please contact 1-800-986-3460 for further assistance.

1

Fastening the Base Bracket

2

Attaching the Small Base Bracket

Use four Screws (EE) and four Washers (JJ) to fasten the Use 1 Screw (DD) to fasten the Small Base Bracket (II) to the Fireplace (B).

Base Bracket (D) to the Base (E).

JJ

EE

3

Attaching the Base Bracket

Fasten the Base Bracket (D) to the Fireplace (B) with the provided Screw (EE).

D

E

B

II

DD

B

12

EE

D

HOMEDEPOT.COM/HOMEDECORATORS

Please contact 1-800-986-3460 for further assistance.

4

Fastening the Base Bracket

Use 1 Screw (EE) to fasten the Base Bracket (D) to the Fireplace (B).

B

5

Secure the Top Frame

Mount Front Frame (C) to the Fireplace (B) by hooking the clips into position.

Tighten the 2 Screws (CC).

Continue to the fuel bed setup instructions (Page 18 ).

D

C

E

EE

B

D

E

13

HOMEDEPOT.COM/HOMEDECORATORS

Please contact 1-800-986-3460 for further assistance.

BUILT IN TO A WALL INSTRUCTIONS

This fireplace is a zero clearance design. No combustibles can be placed on the top surface of the fireplace.

Combustibles may be installed to the edge of the unit. Insulation and vapor barrier should be placed a minimum of 2 inches from the unit.

Build the framing according to the specifications shown in the below table & figure 1.

Model

36HF100GRG /

36HF100GRG-01

47HF100GRG /

47HF100GRG-01

A B

32.8” 18.6”

43.3” 18.6”

C

3.9”

3.9”

D

36”

E

19.7”

46.2” 19.7”

F

4.5”

4.5”

G

31.8”

42.3”

H

18”

18”

I

3.5”

3.5”

J K L

37.2” 26.3” 26.3”

47.5” 33.6” 33.6”

Fig. 1

WIRING REQUIREMENTS

Use appropriate wire to meet local and national electrical codes for rated power consumption. All wire gauges should be 12 gauge solid wires with a dedicated 15 amp breaker for 120 volts.

14

HOMEDEPOT.COM/HOMEDECORATORS

Please contact 1-800-986-3460 for further assistance.

1

Removing the Stickers

Remove the black stickers.

2

Fastening the Brackets

Fasten the Wall Brackets (HH) with Screws (DD).

DD

Black stickers

HH

3

Steps 3 to 6 describe optional installation for removing the power cord and changing to hard wired

Remove the pre-attached Screw (DD) holding the junction box cover.

Loosen the three screws holding the wires and remove the Negative, Live and Ground wires.

Terminals

L N G

Terminals

15

Junction Box Cover Loosen the 3 screws

HOMEDEPOT.COM/HOMEDECORATORS

Please contact 1-800-986-3460 for further assistance.

4

Loosening the Strain Relief Bracket

5

Fastening the Brackets

Remove the two pre-attached Screws (DD) holding the Remove the power cord and strain relief assembly.

power cord strain relief bracket.

G

G

G

G

Strain Relief

Power Cord Assembly

6

Connecting the Power Supply Wire

Connect the power supply wire.

G

G

Terminals

16

Terminals

Power Supply Cord

HOMEDEPOT.COM/HOMEDECORATORS

Please contact 1-800-986-3460 for further assistance.

G

G

7

Installing the Fireplace

Secure the fireplace to the wall using Anchor Screws (AA).

8

Hanging the Front Frame

Hang the Front Frame (C) on the Fireplace (B) and gently push on the lower part of the frame until it snaps into place.

B

AA

9

Securing the Top Frame Hooks

Secure the top frame hooks with the two retaining

Screws (CC).

C

B CC

C

17

HOMEDEPOT.COM/HOMEDECORATORS

Please contact 1-800-986-3460 for further assistance.

1

Removing the Logset

If you wish to remove the logset, unscrew the two

Screws (GG) securing the emberbed.

2

Removing Logset and the Black Stickers

Remove the logset and the black stickers on both sides.

Black stickers

Emberbed with logset

GG

3

Placing Transparent Tray

Place the Transparent Tray (H) inside the Fireplace (B).

H

18

HOMEDEPOT.COM/HOMEDECORATORS

Please contact 1-800-986-3460 for further assistance.

4

Tightening the Screws

Tighten the Screws (FF) on both sides.

5

Removing the Tray Cover

Carefully pull the tray tabs to remove the tray cover.

FF

6

Removing the Tray Cover

Remove the tray cover.

Tray Co ver

7

Placing Fireglass or Rocks

Place the Fireglass (I) or the Rocks (G) as desired.

Follow steps 5 and 6 in reverse to re-install the tray cover.

B

G

19

I

HOMEDEPOT.COM/HOMEDECORATORS

Please contact 1-800-986-3460 for further assistance.