Classe 300
Installation Manual
Advanced Configuration
The advanced configuration gives the possibility of configuring all the basic settings, the quick actions and the camera, intercom, and activation functions, without being bound to a predefined set.
First switching on
After connecting the device, perform the customisations.
Wait for the LEDS to stop flashing and then touch the display to switch it on.
Languages Next
1
English
Français
Italiano
Español
Deutsch
Néerlandais
Português
2
1. Touch the icon for the desired language.
2. Touch to continue.
Back Time and date Next
4
11 d
11 42 m
10 m
2013 y
3
5
3. Touch the icon for the parameter to set (date or time); the icons to increase or decrease the value appear.
4. Touch to set it.
5. Touch to continue.
31
Classe 300
Installation Manual
Now it is possible to display some information concerning the configuration of the device
Back Info End
A
N
00
P
00
7
Master/Slave
Power supply
Firmware ver.
Professional studio
Answering machine
Configuration
Master
Disabled
1.0.12
Enabled
Enabled
6
Display:
A. The configuration parameters.
B. If the device has been set as apartment master or slave.
C. If an additional power sully is present.
D. The firmware version of the device.
E. If the Professional Studio (Office) function is active.
F. If the Answering machine function is active.
6. Press the End key to go to the home page, postponing the configuration to a later date.
7. Now touch to access the configuration section.
B
C
D
E
F
Back
Generals
Intercom
Camera
Actuation
10
Configuration
00 00
P
Answering machine
Professional studio
9
8
8. Enter the N configurator values to set the address device and enter the P configurator values to set the address of the EP of which you can open the Door Lock with IU idle, and to which you can send the auto-on command.
9. Touch to make the functions available in the home page.
10. Proceed with the advanced configuration, see configuration
section.
32
Classe 300
Installation Manual
10:36
Tuesday, 22 April 11
Answering machine Memo Settings Pager
Lock
11. Touch to proceed with the device customisation in the Settings
section.
Azioni rapide
Private camera
External intercom
33
Classe 300
Installation Manual
Settings
Generals
Ringtones
Time and date/Language/Information/Key tone
Volume/Intercom ringtone/Entrance Panel Ringtone/Other ringtones...
Display
Clean monitor/Background/Calibration
Answering machine
Recording Mode/Welcome Message/Record Message...
For the above mentioned settings, refer to the
Settings section of the physical configuration.
Configuration
General/Intercom/Camera/Activation/Change password
Quick Actions
Add quick action
Configuration
Back Settings
Generals
Ringtones
Display
Answering machine
Quick Actions
Configuration
1
Time and date
Language
Info
Tone buttons
1. Touch to configure the device in advanced mode.
In order to access this section, the password must be entered.
Back Configuration
Insert installer password
Confirm
2 q a w
?123
s z e d x r f c t g v y h b u
3 j n i k m
.
o l p
2. Enter the password (default 12345).
3. Touch to save it.
34
Classe 300
Installation Manual
General settings
Back
Generals
Intercom
Camera
Actuation
Change password
00 00
P
Answering machine
Professional studio
2
1
1. Enter the N configurator values to set the address device and enter the P configurator values to set the address of the EP of which you can open the Door Lock with IU idle, and to which you can send the auto-on command.
2. Touch to make the functions available in the home page.
Intercom
This section can be used to configure the intercoms that will enable the user to communicate with other video/audio handsets installed in the home, or in other apartments, or to use the sound system as a pager, to call people.
Back
Generals
Intercom
Camera
Actuation
Change password
1
00 00
P
Answering machine
Professional studio
1. Touch to enter the Intercom section.
35
Classe 300
Installation Manual
Back
Generals
Intercom
Camera
Actuation
Change password
Add intercom
2
2. Touch to add an intercom.
Back 6 Add intercom
Type
Internal intercom
Description
Internal intercom 0
Address
00
Save
3
4
5
3. Select the type of intercom among:
Internal: it provides communication among rooms of the same apartment (or among devices of different apartments but only if there are no apartment interfaces)
External: it provides communication among rooms of different apartments (if there are apartment interfaces)
Paging: it provides communication with the sound system
General: it provides communication with all internal units
Warning: if no apartment interface has been installed in the system, the call will be made to all residents, otherwise it will remain within the apartment.
4. Change name.
5. Enter address:
Internal: address of the device wired in the same apartment
External: address of another apartment
6. Touch to save.
36
A
Classe 300
Installation Manual
Back
Generals
Intercom
Camera
Actuation
Change password
Add intercom
Internal intercom 0
External intercom 0
Pager 0
General intercom 0
B
A. Change the name of the intercom.
B. Delete intercom.
Camera
This section can be used to configure the cameras that will give users the possibility of displaying the images from their own apartments, the apartment block area, or a CCTV surveillance system.
Back
Generals
Intercom
Camera
Actuation
Change password
00 00
P
Answering machine
Professional studio
1
1. Touch to enter the Camera section.
37
Classe 300
Installation Manual
Back
Generals
Intercom
Camera
Actuation
Change password
Add camera
2
2. Touch to add a camera/entrance panel.
Back 6
Add camera
Type
Private camera
Description
Private camera 0
Address
00
Save
3
5
4
3. Select the type of camera/entrance panel among:
Private: it gives the possibility of displaying the images from a camera/entrance panel installed in the own apartment (if an apartment interface has been installed)
Public: it gives the possibility of displaying the images from a camera/entrance panel installed in a common area, visible to all residents (if an apartment interface has been installed)
Warning: for apartment blocks without apartment interface and in single-family homes, cameras must be considered as PRIVATE.
CCTV: it gives the possibility of displaying the images from a camera of a video video surveillance system integrated with the video door entry SCS system.
The image is displayed for three minutes and the camera cycling is not possible. For the camera cycling or multi-vision functions, connect interface 347400 to a device output (e.g.
Digital Video Recorder) performing these functions.
Warning: to realize this integration, refer to the guides or the diagrams of the SCS/coaxial interface 347400.
38
4. Change name.
5. Enter the address of the camera/entrance panel
6. Touch to save.
Back
Generals
Intercom
Camera
Actuation
Change password
Add camera
Private camera 0
Public camera 0
TVCC 0
A
Classe 300
Installation Manual
B
A. Change the name of the camera/entrance panel.
B. Delete camera/entrance panel.
Activation
In this section it is possible to configure the actuators in your system (e.g. door lock, garden light, etc.) and to activate them for the user.
Back
Generals
Intercom
Camera
Actuation
Change password
00 00
P
Answering machine
1
Professional studio
1. Touch to enter the Activation section.
39
Classe 300
Installation Manual
Back
Generals
Intercom
Canera
Actuation
Change password
Add actuation
2
2. Touch to add an activation.
Back 6
Add actuation
Type
Lock
Description
Address
Lock 0
00
5
3. Select the type of activation among:
Lock: it is possible to activate a door lock actuator
Generic actuator: it is possible to activate a generic actuator
4. Change name.
5. Enter the address of the actuator
6. Touch to save.
4
Save
3
40
A
Classe 300
Installation Manual
Back
Generals
Intercom
Canera
Actuation
Change password
Add actuation
Lock 0
Lock 1
Generic actuator
A. Change the name of the activation.
B. Delete activation.
Change password
In this section it is possible to modify the password used to enter the configuration section.
Back
Generals
Intercom
Camera
Actuation
Change password
00 00
P
Answering machine
Professional studio
1
1. Touch to enter the Change passwors section.
B
41
Classe 300
Installation Manual
Cancel Confirm
New password
Repeat password q a w
?123
s z 3 e d x r f c t g v y h b u j n i
2 k m
.
o l p
1. Enter the new password using the keypad.
2. Repeat the new password.
3. Touch to save it.
Once the system functions have been configured, some can me made available to the users, giving them the possibility of selecting the 4 Quick Actions to display in their home page.
Quick actions
Warning: before using these functions, insert the relevant functions in the “
Configuration ”
section.
Settings Back
Generals
Ringtones
Display
Answering machine
Quick Actions
Configuration
Add quick action
1
1. Touch to add a quick action.
42
Back
Cameras
Intercom
Activations
A
Add quick action
Private camera 0
Public camera
TVCC
Classe 300
Installation Manual
B
2
A. Available Functions.
B. Function already used as quick action.
2. Touch to select the function to be used as quick action.
Back Settings
Generals
Ringtones
Display
Answering machine
Quick Actions
Configuration
Private camera 0
Public camera
Internal intercom
External intercom
It configures up to 4 quick actions.
43
