CONTROL AND INICATORS. Macrom sp 4050


Add to My manuals
30 Pages

advertisement

CONTROL AND INICATORS. Macrom sp 4050 | Manualzz

O/M SP 4.050 25/06/02 18:17 Page 8

CONTROLS AND INDICATORS

6 • "4CH/3CH/2CH" Output mode switch: selects the output configuration of the amplifier in the following ways:

2ch 3ch 4ch a) "4ch" configuration using 4 output channels: In this mode the amplifier can function with a double stereo system, front and rear.

b) "3ch" configuration using three output channels: In this mode the amplifier can function with a stereo system in Front and a "bridged" mono system in

Rear.

2ch 3ch 4ch c) "2ch" Configuration using 2 output channels: In this mode the amplifier can be used as a traditional 2-channel stereo amplifier with twice the normal power.

2ch 3ch 4ch

Nota: Con la configurazione “2ch”, le regolazioni della sensibilità diventano indipendenti, cioè, la sezione Front regala la sensibilità del canale Sinistro, mentre la sezione Rear regola la sensibilità del canale Destro. In oltre se si volesse attivare il crossover è attivo solamente quello della sezione Rear, di conseguenza il suo controllo per la regolazione della frequenza.

7 • Rear Crossover switch: select the output mode of the amplifier by activating the Low-

Pass or High-Pass filter.

Flat Low High a) Flat: the amplifier will reproduce the entire audio range in relation to the signal applied at the input.

20Hz 20kHz b) Low-Pass: activation of the low-pass filter, i.e.

determination of the finishing-point of the low frequencies present at the Rear outputs.

c) High-pass: activation of the low-pass filter, i.e.

determination of the starting-point of the high frequencies present at the Rear outputs.

Flat Low High

Flat Low High

20Hz 30 > 600Hz

30 > 600Hz 20kHz

8 • C o n t i n u o u s a d j u s t m e n t o f t h e R e a r L o w - P a s s o r H i g h - P a s s

Frequencies: once the high-pass or low-pass filter is inserted, the crossover frequency can be adjusted between 30 Hz and 600 Hz in continuous mode.

40

50

35

30

60

Hz

80

125

300

600

9 • Adjustment of the Rear Input gain: adjusts the input sensitivity of the amplifier, which varies from 200 mV to 4V.

4V 0,2V

10 •Rear RCA input connectors: Connect the Pre output leads of your main unit to the amplifier input. These inputs will drive the final stages of the Rear section.

8

O/M SP 4.050 25/06/02 18:17 Page 9

CONTROLS AND INDICATORS

11 • Speaker connectors: Outputs for connecting the loudspeakers.

The amplifier allows the loudspeakers to be connected with a minimum impedance of 2 Ohm for a channel in stereo configuration, and with an impedance of 4 Ohm for a "bridged" mono connection.

If the 3 channel configuration is to be used, the total impedance should not exceed the minimum value of 2 Ohm.

Make sure that the polarity of the connection between the loudspeakers is correct. Do not allow inadequately insulated leads to come into contact with Ground, any metallic parts of the car, or with each other.

Bridged

L R

Front

Bridged Bridged

L R L R

Rear

Front Front

Rear Rear

3-channel configuration 2-channel configuration 1-channel configuration

12 • Fuses: When replacing fuses, make sure that they are replaced with fuses of the same ampere rating. Use of the wrong type of fuse could seriously damage the components.

13 • + BATT connector: Connect the positive "+" of the battery directly, by means of a fuse located nearby, and use a lead having a sufficiently large cross-section to allow passage of the current. Do not connect this terminal to the car's own electrical circuit.

14 • REMOTE-ON connector: Connect this to the remote-on start-up output lead (remote starting switch) or to the automatic antenna wire running from the main unit. It will now be possible to turn the amplifier on and off from the main unit.

15 • GND connector: Attach this Ground connector, using a lead of adequate section, to a clean point on any metallic part of the car chassis, if possible to an already-installed screw.

Never attach this clamp directly to the negative point of the battery, which could give rise to an unpleasant buzzing noise while the car is being driven.

16 • Check control indicator: This LED indicates the amplifier functioning status.

WHITE: The unit is switched off

GREEN: The amplifier is functioning perfectly

RED: the unit is in a state of protection.

The amplifier is equipped with three protection devices:

- Overheating: If errors have been made during installation, and the amplifier overheats, the unit will enter into a state of protection before any damage can occur. Once the temperature returns to normal and the errors have been rectified, the unit will automatically start to function normally once again.

- Overloading: If several loudspeakers have been connected to the amplifier and the total impedance drops below the 1 Ohm limit that it can handle, the amplifier goes into a state of protection. The main unit will have to be switched off and on again in order to restore the amplifier to normal functioning.

- Short circuit in an output: In the case of a short circuit in the loudspeaker outputs, the unit will go into a state of protection to avoid serious damage to the final transistors. Normal functioning will be restored when the short circuit has been dealt with and the main unit switched on again.

9

advertisement

Related manuals