SPECIFICATIONS
Fluid Capacities/Lubricants
Component/
Application
Diesel Engine
Lubricant
Engine Oil
2
Specification
SAE 10W-40
HVLP46
PANOLIN HLP Synth 46
BP BIOHYD SE-46
KP2N-20 calcium sulfonate complex
KF2K-25 lithium
FINA Marson L2
2-D ASTM D975 – 94
1-D ASTM D975 – 94
Season/
Temperature
-4°F (-20°C)
+104°F (+40°C)
Year-round
Capacity
1
3.5 qts. (3.3 L)
Travel Drive
Hydraulic Oil Tank
Grease
Grease Zerks
Battery Terminals
Diesel Fuel Tank
Gearbox Oil
3
Hydraulic Oil
4
Biodegradable Oil
Roller and
Friction Bearings 6
Open Gear
(live ring gears)
5
Multipurpose Grease
Acid-proof Grease 8
Diesel Fuel
9
7
SAE 80W-90
KF2K-25 lithium
Year-round
Year-round
Year-round
Year-round
Depending on outside temperatures
Year-round
0.63 qts. (0.6
L) each
7 gal. (26.5 L)
(Complete system capacity:
14 gal. [53 L])
As Required
As Required
As Required
9.5 gal. (36 L)
Engine and Hydraulic
Oil Cooler
Coolant Soft water + antifreeze
ASTM D4985
Distilled water + antifreeze
ASTM D4985
Water + Antifreeze
1.2 gal. (4.5 L)
Windshield Washer Cleaning Agent Year-round 1.25 qts. (1.2
L)
1. Capacities shown are approximate; use only oil level check to determine correct oil level
2. BP Vanellus MG 15W40, BP Vanellus C-Extra 10W30, Chevron Delo 400 15W40 or equivalent
3. Hypoid gearbox oil based on basic mineral oil (API GL-4, GL-5)
4. Mobile DTE15M, Amoco Rykon 46, BP Energol HLP-HD 46 or equivalent
5. Hydraulic ester oils (HEES)
6. FINA Energrease 21M, Chevron RPM Heavy-Duty Grease No. 2, Mobilgrease Moly 52, or BP Energrease Moly
EP2
7. FINA Energrease 21M, Chevron RPM Heavy-Duty Grease No. 2, Mobilgrease Moly 52, or BP Energrease Moly
EP2
8. Standard acid-proof grease
9. Sulphur content below 0.05%; Cetane number over 45
918254/BP0112 1-4 Printed in U.S.A.
Engine
Make and Model
Type
Displacement
Bore and Stroke
Net Power
Max. Torque
Max. Engine Speed (with no load)
Idle Engine Speed
Fuel Injection System
Starting Aid
Max. Inclined Angle (engine still supplied with oil)
Exhaust Emission Compliance
Hydraulic System
Pump
Flow Rate (@2500 rpm)
Working Pressure
Swing System Pressure
Boom/Bucket/Dipper Arm Pressure
Dozer Blade Pressure
Hydraulic Oil Cooler
Filter
Dozer Blade
Width
Height
Maximum Lift Above Ground
Maximum Depth Below Ground
Yanmar 3TNV76-NNS
3-cylinder, water-cooled diesel
68 cid (1116 cc)
2.9 x 3.2 in. (76 x 82 mm)
20.4 hp (15.2 kW) @ 2500 rpm
48.75 lb.-ft. (66.1 Nm) @ 1800 rpm
2675 +/- 25 rpm
1300 +/- 25 rpm
Indirect Injection
Glow Plug (preheating time 4 seconds)
25° in all direction
97/68EC; U.S. EPA – Tier 4 compliant
Double variable-capacity + Two gear pumps
0.70 + 0.70 + 0.48 + 0.16 cu. in.
(11.5 + 11.5 + 8 + 2.7 cm
3
)
8.1 + 8.1 + 5.6 + 2.0 gpm
(30.8 + 30.8 + 21.4 + 7.2 L/min.)
3263 psi (225 bar)
2987 psi (206 bar)
3263 +/- 44 psi (225 +/-3 bar)
2988 +/- 44 psi (206 +/-3 bar)
Standard
Return
5' 2" (1570 mm)
11.4" (290 mm)
15" (380 mm)
16.5" (419 mm)
Printed in U.S.A.
1-5 918254/BP0112
Undercarriage and Swing System
Travel Speed (Dual Speed)
Low Speed
High Speed
Ground Clearance
Swing (Slew) Speed
Gradability
Rubber Track Width
Top / Bottom Rollers (per side)
Sprocket Center
Average Ground Pressure
Maximum Drawbar Pull
Electrical System
Alternator
Starter
Battery
Socket
Fuses
9
1 2 3 4 5 6 7 8
10
1.3 mph (2.1 km/hr)
2.3 mph (3.8 km/hr)
10.9" (277 mm)
10.25 rpm
30° = 58%
11.8" (300 mm)
1 / 3
104" (2642 mm)
3.8 psi (26.2 kPa)
5732 lbf (25.5 kN)
12 V, 40 A
12 V, 1.1 kW
12 V, 44 Ah; 630 CCA
15 A max. - Accessory Socket
7
8
9
10
5
6
3
4
Fuse No.
1
2
Rated
Current Protected Circuit
15 A
10 A
Accessory socket, cigarette lighter
Rotating beacon, radio
5 A
15 A
10 A
15 A
Proportional controls (unused)
Windshield wiper, interior light
Cab roof lights
Valves, horn
15 A
10 A
40 A
50 A
Boom light, heating
Indicators, cutoff solenoid, relays
Start, preheat, cutoff solenoid
Ignition lock
918254/BP0112 1-6 Printed in U.S.A.
Relays
K9
V1
K8
K6
Relay No.
V1
K6
K7
K8
K9
Protected Circuit
Blocking diode
Preheating time lag relay
Starting relay
Cutoff solenoid time lag relay
Pickup contact cutoff solenoid relay
K7
Coolant Compound Table
Note: Do not mix coolant types. Machine filled at factory with Eurolub SF D12 (ethylene glycol basis)
Outside
Temperature
Up to °F (°C)
+39 (4)
+14 (-10)
-4 (-20)
-13 (-25)
-22 (-30)
-34.6 (-37)
Water
% by Volume
99
79
65
59
55
50
Coolant: Halvoline XLC (based on ethylene glycol)
Anti-corrosion Agent Antifreeze Agent in³/gal (cm³/L)
% by Volume
% by Volume
2.6 (10) 1
–
20
34
40
44
50
Sound Levels
Sound Power (L
WA
)
Sound Pressure (L
PA
)
97 dB(A)
68 dB(A)
Printed in U.S.A.
1-7 918254/BP0112
General Specifications
9' 3.25" (2827 mm) 2' 6"
(759 mm)
7' 11"
(2413 mm)
7' 11"
(2413 mm)
11.75"
(299 mm)
1 ' 9"
(533 mm)
6' 10.5" (2242 mm)
75
º
2 ' 6"
(764 mm)
50°
5 ' 2" (1570 mm)
R = 2
(759 m
' 6" m)
1 ' 0"
(300 mm)
6' 7.5" (2021 mm)
3' 2"
(970 mm)
5' 2" (1575 mm) 13' 11" (4255 mm) 1' 0"
(300 mm)
1' 0"
(300 mm)
Weight (with cab)
Weight (with canopy)
Height
Width
Transport length
Dipper arm length
Max. digging depth
Max. vertical wall digging depth
Max. digging height
Max. dump height
Max. digging radius
Max. reach at ground level
Max. bucket dig force
Max. arm force
Min. tail swing radius
Max. tail end lateral projection over tracks
5886 lbs. (2670 kg)
5681 lbs. (2577 kg)
7' 11" (2413 mm)
5' 2" (1575 mm)
13' 11.5" (4254.5 mm)
4' 1" (1250 mm)
9' 0" (2743 mm)
7' 1" (2152 mm)
14' 1" (4299 mm)
9' 8.9" (2972 mm)
15' 4" (4681 mm)
15' 4" (4681 mm)
5057 lbf (22.5 kN)
4923 lbf (21.8 kN)
2' 6" (760 mm)
0' 0" (0 mm)
Max. boom distance to bucket center (right side) 1' 9" (533 mm)
Max. boom distance to bucket center (left side) 2' 6" (764 mm)
Max. swing (slew) angle (left side/right side) 75°/ 50°
918254/BP0112 1-8 Printed in U.S.A.
Fields of Applications/Approved Attachments
The machine is designed and intended to be used only with the approved attachments listed in the following table. To avoid possible personal injury, equipment damage or performance problems, use only attachments that are approved for use on and within the rated operating capacity of the machine. Contact your dealer or the Manitou Americas, Inc. service department for information about attachment approval. Manitou
Americas, Inc. cannot be responsible if the machine is used with non-approved attachments.
Attachment
Heavy-Duty Bucket
Ditching Bucket
Swivel Bucket
Size
12 in. (300 mm)
16 in. (400 mm)
20 in. (500 mm)
24 in. (600 mm)
30 in. (700 mm)
42 in. (1000 mm)
55 in. (1400 mm)
39 in. (1000 mm)
55 in. (1400 mm)
Capacity
1.8 ft
3
(0.051 M
3
)
2.4 ft 3 (0.068 M 3 )
3.1 ft 3 (0.088 M 3 )
3.8 ft 3 (0.108 M 3 )
4.8 ft 3 (0.136 M 3 )
4.1 ft
3
(0.116 M
3
)
5.9 ft
3
(0.167 M
3
)
3.9 ft
3
(0.110 M
3
)
5.6 ft
3
(0.159 M
3
)
Printed in U.S.A.
1-9 918254/BP0112
Load Diagrams
Without Counterweight
+4.0m
+3.0m
+2.0m
A +1.0m
0.0m
-1.0m
-2.0m
+4.0m
+3.0m
+2.0m
+1.0m
0.0m
B
Maximum permissible loads
MAX
11' 6"
(3.5 m)
A
B
+9' 10"
(+3.0 m)
+6' 6"
(+2.0 m)
+3' 3"
(+1.0 m)
0' 0"
(0.0 m)
-3' 3"
(-1.0 m)
1009*
(458*)
985*
(447*)
1000*
(453*)
1026*
(465*)
1033*
(468*)
747
(339)
558
(253)
499
(226)
512
(232)
626
(284)
993*
(450*)
1161*
(526*)
1269*
(575*)
705
(320)
659
(299)
621
(282)
9' 10"
(3.0 m)
933*
(423*)
1044*
(473*)
1378*
(625*)
1588*
(720*)
1425*
(646*)
933*
(423*)
919*
(417*)
837
(380)
776
(352)
769
(349)
8' 2"
(2.5 m)
1788*
(811*)
2116*
(960*)
1879*
(852*)
1101
(499)
1009
(458)
1004
(455)
B
*
Maximum permissible load on extended dipper arm
A Overhang from the center of the turntable
Height of load fixing point
Lifting capacity hydraulically limited
All table values are in lbs. (kg) and for a machine in a horizontal position on firm ground without bucket.
Dozer blade support in drive direction.
Dozer blade support 90° to drive direction.
If equipped with a bucket or other implements, lift capacity or tilt load is reduced by bucket or implement weight.
Calculation basis: According to ISO 10567.
The excavator’s lift capacity is restricted by the settings of the pressure relief valves and the hydraulic system's stabilizing features.
Neither 75% of the static tilt load nor 87% of the hydraulic lift capacity is exceeded.
918254/BP0112 1-10 Printed in U.S.A.
With Counterweight
+4.0m
+3.0m
+2.0m
A
+1.0m
0.0m
-1.0m
-2.0m
+4.0m
+3.0m
+2.0m
+1.0m
0.0m
B
Maximum permissible loads
MAX
11' 6"
(3.5 m)
A
B
+9' 10"
(+3.0 m)
+6' 6"
(+2.0 m)
+3' 3"
(+1.0 m)
0' 0"
(0.0 m)
-3' 3"
(-1.0 m)
1121*
(508*)
1078*
(489*)
1088*
(494*)
1110*
(504*)
1098*
(498*)
941
(427)
706
(320)
640
(290)
670
(304)
391
(399)
1084*
(492*)
1222*
(554*)
1282*
(581*)
808
(366)
768
(348)
738
(335)
9' 10"
(3.0 m)
1085*
(492*)
1157*
(525*)
1463*
(663*)
1611*
(731*)
1335*
(605*)
1085*
(483*)
1041*
(472*)
965
(437)
914
(414)
919
(417)
8' 2"
(2.5 m)
1297*
(588*)
1923*
(872*)
2132*
(967*)
1774*
(805*)
1297
(588)
1253
(568)
1182
(536)
1191
(540)
B
*
Maximum permissible load on extended dipper arm
A Overhang from the center of the turntable
Height of load fixing point
Lifting capacity hydraulically limited
All table values are in lbs. (kg) and for a machine in a horizontal position on firm ground without bucket.
Dozer blade support in drive direction.
Dozer blade support 90° to drive direction.
If equipped with a bucket or other implements, lift capacity or tilt load is reduced by bucket or implement weight.
Calculation basis: According to ISO 10567.
The excavator’s lift capacity is restricted by the settings of the pressure relief valves and the hydraulic system's stabilizing features.
Neither 75% of the static tilt load nor 87% of the hydraulic lift capacity is exceeded.
Printed in U.S.A.
1-11 918254/BP0112
NOTES
918254/BP0112 1-12 Printed in U.S.A.
