LIFTING THE MACHINE WITH A
CRANE
Only lift the machine according to the following guidelines:
• The crane and rigging equipment must have suffi-
cient capacity. See “Lifting the Machine” on page
3-28.
•
Lift the machine according to “Lifting the
Machine” on page 3-28.
• Secure the machine against unintentional movement. Use taglines as needed.
• Do not lift the machine with persons on or in the machine.
• Any person guiding the crane operator must be within sight or sound of the crane operator.
• Lift the machine only with the standard bucket installed, the bucket empty and in the transport position.
• Persons must stay clear of and not under the machine when it is lifted.
• Fasten the rigging equipment so the machine is horizontal when it is lifted.
• Do not lift the machine by the eye hooks on the cab. Attach the rigging equipment only at the lift points identified by this symbol:
SAFETY AND INFORMATION
DECALS
The machine has decals shown on the following pages that provide safety information and precautions. These decals must be kept legible. If missing or illegible, they must be replaced promptly. Replacements can be obtained from your dealer.
Refer to the Parts Manual for decal part numbers and ordering information.
New Decal Application
Surfaces must be free of dirt, dust, grease and foreign material before applying the decal. Remove the smaller portion of the decal backing paper and apply the exposed adhesive to the clean surface, maintaining proper position and alignment. Peel the rest of the backing paper and apply hand pressure to smooth out the decal surface. Refer to the following pages for proper decal locations.
If replacing a part that has a decal on it, ensure that the replacement part has the same decal.
TRANSPORTING
Obey state and local over-the-road regulations. Check state and local restrictions regarding weight, width and length of a load. The hauling vehicle, trailer and load must all be in compliance with local regulations. Refer to the Transporting section of this manual.
918254/BP0112 2-10 Printed in U.S.A.
ISO-Style Safety Decal Locations (Later Machines)
7
1
11
1
9
1
13
8
12
10
3
12
14
2
3
5
4
3
6
WARNING! Danger Zone Decal
AVOID INJURY OR DEATH!
Located on both sides of the boom.
Keep bystanders away from the machine when it is in use.
2
WARNING! Hydraulic Reservoir Under Pressure
AVOID INJURY OR DEATH!
Located on the fuse box cover under the hydraulic system vent valve inside the engine compartment.
Relieve hydraulic pressure before servicing machine. Removed hydraulic reservoir cap slowly.
Refer to the maintenance section in the operator’s manual before servicing the machine.
WARNING! Stay Clear Decal
AVOID INJURY OR DEATH!
Located next to the track tension grease fitting on both sides of the machine.
WARNING! Grease is under high pressure. Keep your face and body away from the fitting.
Do not loosen the fitting more than two turns. Do not loosen parts other than the fitting.
Refer to the operator’s manual for track adjustment procedure.
4 WARNING! Hot Surfaces Decal
AVOID SERIOUS INJURY!
Located inside the engine compartment.
Stop the engine and wait for all parts to cool before opening the engine compartment. Hot surfaces can cause severe burns.
Read the operator’s manual before performing any maintenance on the machine.
Printed in U.S.A.
2-11 918254/BP0112
ISO-Style Safety Decal Locations (Later Machines) (Continued)
5 8
WARNING! Rotating and Hot
Components Decal
AVOID SERIOUS INJURY!
Located on the fan shroud inside the engine compartment.
Stop the engine and wait for all parts to cool before opening the engine compartment. Rotating parts can cause severe injury. Hot surfaces and liquids can cause severe burns.
Read the operator’s manual before performing any maintenance on the machine.
9
WARNING! Read Operator’s
Manual
AVOID INJURY OR DEATH!
Located on the door pillar inside the cab.
Read the operator’s manual before operating or performing any maintenance on the machine.
6
WARNING! Rotating Components! Danger of
Entanglement! Decal
AVOID SERIOUS INJURY!
Located below the engine cover latch.
Stop the engine before opening the engine compartment. Rotating parts can cause severe injury.
WARNING! Decal
AVOID INJURY OR DEATH!
Located on the door pillar inside the cab.
No riders! Never use work tool as work platform.
Operate only from operator’s seat.
ALWAYS wear seatbelt.
WARNING: Avoid Overturn
Side stability is reduced when: 1) turning; 2) operating on rough terrain or side slopes; and 3) carrying load raised.
Carry load low. Do not exceed
Rated Operating Capacity.
Avoid steep slopes and high speed turns.
Travel up and down slopes with heavy end uphill.
Read the operator’s manual before operating the machine.
7
10
WARNING! Crushing Hazard Decal
AVOID SERIOUS INJURY!
Located on the inside of the front window on cabequipped machines.
Only open and close the front window using the handles.
Always lock the front window using both locks.
WARNING! Hot Components Decal
AVOID SERIOUS INJURY!
Located on the hydraulic valve compartment cover in the location of the hydraulic oil fill (hydraulic oil fill is located inside the hydraulic valve compartment).
Stop the engine and wait for all parts to stop and cool before. Hot surfaces and liquids can cause severe burns.
Read the operator’s manual before performing any maintenance on the machine.
918254/BP0112 2-12 Printed in U.S.A.
ISO-Style Safety Decal Locations (Later Machines) (Continued)
11 13
WARNING! Danger Zone Decal
AVOID INJURY OR DEATH!
Located on the back of the swing frame.
Keep bystanders away from the machine when it is in use.
12
WARNING! Mandatory Safety
Shutdown Decal
AVOID INJURY OR DEATH!
Located on the door pillar inside the cab.
Before leaving the machine, or performing any service on the
machine, perform the “Mandatory
Safety Shutdown Procedure” on page 2-2.
1. Lower the working equipment to the ground and support it securely.
2. Run the engine at idle speed for a few minutes to allow systems to cool after operation at full speed.
3. Turn the key fully counterclockwise to shut off the engine.
4. Lock out controls by raising left control console.
5. Remove the ignition key and take it with you.
WARNING! Danger Zone Decal
AVOID INJURY OR DEATH!
Located on both sides of the boom swivel bracket.
Swiveling boom can cause crushing. Keep bystanders away from the machine when it is in use.
14
WARNING! Hot Components Decal
AVOID SERIOUS INJURY!
Located near the hydraulic system vent valve inside the engine compartment.
Stop the engine and wait for all parts to stop and cool before. Hot surfaces and liquids can cause severe burns.
Read the operator’s manual before performing any maintenance on the machine.
Printed in U.S.A.
2-13 918254/BP0112
ISO-Style Information Decal Locations (Later Machines)
6 7
2
7 3
2
2
3
4
1
8
2
5
4
5
1
2
5
Track Front Decal
Located near the front of the track frame on both sides of the machine
Indicates the front of the track frame.
1
Lift Point Decal
Located on both sides of the boom on the dipper arm cylinder bracket and on both ends of the dozer blade.
Apply lift hooks only in these locations.
Hydraulic Fluid Decal
Located on the back of the cab/ canopy in the location of the hydraulic oil fill (hydraulic oil fill is located inside the hydraulic valve compartment).
USE HYDRAULIC FLUID ONLY!
Diesel Fuel Decal
USE DIESEL FUEL ONLY!
Located near the fuel filler.
5
6
5
Tie-Down Point Decal
Located on both ends of the dozer blade and near the rear end of the track frame on both sides of the machine.
Only use tie-down points to secure the machine during transport.
Operator Controls Decal
Located on the ceiling inside the cab/canopy.
Provides quick-reference for the SAE operator’s control option inside the cab.
Read the operator’s manual before operating the machine. Refer to the operator’s manual for details about the operator’s controls.
918254/BP0112 2-14 Printed in U.S.A.
ISO-Style Information Decal Locations (Later Machines) (Continued)
7 8
KF K -
KF K -
KP 0
KF K -
KF K -
KF K -
KF K -
Maintenance Decal
Located on the back window of the cab and the side of the canopy.
Provides maintenance intervals quick-reference.
Read the operator’s manual before maintenance on
the machine. Refer to “Maintenance Schedule” on page 4-5.
Lift Capacity Decal
Located on the back window of the cab.
Provides maintenance intervals quick-reference.
Read the operator’s manual before maintenance on the machine. Refer to “Maintenance Schedule” on page 4-5.
Printed in U.S.A.
2-15 918254/BP0112
ANSI-Style Safety/Information Decal Locations (Early Machines)
Lift Capacity Label
(cab/canopy ceiling)
Swing Radius Warning Decal
(boom - both sides)
Read Operator’s Manual Decal
(right inside cab/canopy wall)
918254/BP0112 2-16 Printed in U.S.A.
ANSI-Style Safety/Information Decal Locations (Early Machines) (Continued)
Hydraulic Oil & Pressure Warning Decals
(cab frame above rear cover)
Track Tensioner Warning Decal
(track frame - both sides)
Avoiding Injury Decal
(cab/canopy ceiling)
Rotating Fan, Entanglement, and Hot Surface
Warning Decals (inside engine compartment)
Shutdown Procedures Decal
(cab/canopy ceiling)
Hot Surface Warning Decal
(inside engine compartment )
Printed in U.S.A.
2-17 918254/BP0112
ANSI-Style Safety/Information Decal Locations (Early Machines) (Continued)
Front Window Warning Decal
(near cab roof—cab model only)
Avoid Injury Warning Decal
(inside engine compartment)
Rotating Fan Warning Decal
(engine cover hand recess)
918254/BP0112 2-18 Printed in U.S.A.
