ONLINE TREND MODULE. Sulzer AquaProg 6


Add to my manuals
72 Pages

advertisement

ONLINE TREND MODULE. Sulzer AquaProg 6 | Manualzz

13 ONLINE TREND MODULE

Here you can select between showing 6 different online trend signals!

To this you can also choose to show Pump status as well for Start/Stop levels!

This will be a most valuable tool!!

Especially for adjusting the pump capacity calculation or checking the power supply as well for any fault finding in the pump!!!

You can choose between a 15 and 60 minute time window.

In the background AquaProg is receiving up to 20 values per second showing a calculated sampling with 1 or 4 seconds interval depending on selected time window frame.

Sulzer Pump Solutions AB

AquaProg user guide

2014-08-01

Page 66 of 72

The value drawn will be a dot or line depending on how much the value has changed during the sampling calculation!

Depending on communication speed and quality we handle a sampling rate of up to 20 samples per second!

If it is indicated as a vertical line it means we have a span between highest and lowest value during the calculation of the value shown and of course the span!!!

Note! We have not included any print out or save function!

Just use conventional print screen command or any screen dump software!

AquaProg has trend support for:

• PC 242

• PC 441

• CP 112-212

• CP 116-216

A ruler can be placed indicating the actual values and time from current time!

Sulzer Pump Solutions AB

AquaProg user guide

2014-08-01

Page 67 of 72

When connected to a PC 441 you can select between showing the following parameters:

Pump controller PC 441

- Closed

- Pit Level

- Inflow

- Outflow

- Overflow Level

- Overflow Flow

- Back-Pressure

- Power frequency

- Voltage L1-L2

- Voltage L2-L3

- Voltage L3-L1

- Power supply

- P1 Motor Current

- P2 Motor Current

- P3 Motor Current

- P4 Motor Current

- P1 Nom. Pump Capacity

- P2 Nom. Pump Capacity

- P3 Nom. Pump Capacity

- P4 Nom. Pump Capacity

- P1 Power Factor

- P2 Power Factor

- P3 Power Factor

- P4 Power Factor

- P1 Vibrations

- P2 Vibrations

- P3 Vibrations

- P4 Vibrations

- P1 Pump Power

- P2 Pump Power

- P3 Pump Power

- P4 Pump Power

- P2 Motor Current L1

- P2 Motor Current L2

- P2 Motor Current L3

- P3 Motor Current L1

- P3 Motor Current L2

- P3 Motor Current L3

- P4 Motor Current L1

- P4 Motor Current L2

- P4 Motor Current L3

- P1 Temp. Stator T1

- P1 Temp. Upper Bearing

- P1 Temp. Lower Bearing

- P1 Temp. Stator T4

- P2 Temp. Stator T1

- P2 Temp. Upper Bearing

- P2 Temp. Lower Bearing

- P2 Temp. Stator T4

- P3 Temp. Stator T1

- P3 Temp. Upper Bearing

- P3 Temp. Lower Bearing

- P3 Temp. Stator T4

- P4 Temp. Stator T1

- P4 Temp. Upper Bearing

- P4 Temp. Lower Bearing

- P4 Temp. Stator T4

- AI2 P1 Motor Current / Selected funct.

- AI3 P2 Motor Current / Selected funct.

- AI4 P3 Motor Current / Selected funct.

- AI5 P4 Motor Current / Selected funct.

- AO 1 mA Output

- AO 2 mA Output

- PID Set Point

- P1 Motor Current L1

- P1 Motor Current L2

- P1 Motor Current L3

-

-

- P1 Latest Pump Capacity

- P2 Latest Pump Capacity

- P3 Latest Pump Capacity

- P4 Latest Pump Capacity

-

When connected to a PC 242 you can select between showing the following parameters:

Pump controller PC 242

- Closed

- Pit Level

- Inflow

- Outflow

- Overflow Level

- Overflow Flow

- P1 Motor Current

- P2 Motor Current

-

- P1 Nom. Pump Capacity

- P2 Nom. Pump Capacity

- P1 Temperature

- P2 Temperature

- Power supply

- AI4 Back-Pressure / Free choice

- P1 Latest Pump Capacity

- P2 Latest Pump Capacity

-

Sulzer Pump Solutions AB

AquaProg user guide

2014-08-01

Page 68 of 72

When connected to a CP 112-212 you can select between showing the following parameters:

Control Panel CP 112 & CP 212 Control Panel CP 212

- Closed

- Pit Level

- P1 Motor Current L1

- P1 Motor Current L2

- P1 Motor Current L3

- P1 Power Factor

- Back-Pressure

-

- Closed

- Pit Level

- P1 & P2 Motor Current L1

- P1 & P2 Motor Current L2

- P1 & P2 Motor Current L3

- P1 & P2 Power Factor

-

-

When connected to a CP 116-216 you can select between showing the following parameters:

Control Panel CP 116 & CP 216

- Closed

- Pit Level

- Inflow

- Outflow

- Overflow Level

- Overflow Flow

- AI4 Back-Pressure / Free choice

- P1 Motor Current

- P1 Nom. Pump Capacity

- P1 Power Factor

- P1 Motor Current L1

- P1 Motor Current L2

- P1 Motor Current L3

- P1 Latest Pump Capacity

-

Control Panel CP 216

- Closed

- Pit Level

- Inflow

- Outflow

- Overflow Level

- Overflow Flow

- AI4 Back-Pressure / Free choice

- P1 & P2 Motor Current

- P1 & P2 Nom. Pump Capacity

- P1 & P2 Power Factor

- P1 & P2 Motor Current L1

- P1 & P2 Motor Current L2

- P1 & P2 Motor Current L3

- P1 & P2 Latest Pump Capacity

-

Sulzer Pump Solutions AB

AquaProg user guide

2014-08-01

Page 69 of 72

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

advertisement