   Error solution

ERRORS OF THE TC WORK MODE

9001 ‘Cycle without ROUGHING or FINISHING’

DETECTION

CAUSE

SOLUTION

While executing a drilling, facing, taper turning, rounding or profile cycle.

Neither the roughing nor the finishing tools have been seleted.

Select the roughing tool (If T=0, there is no roughing) and the finishing tool (if T=0, there is no finishing).

9002 'ROUGHING: Value of

D=0’

DETECTION

CAUSE

SOLUTION

While executing a drilling, facing, taper turning, rounding or profile cycle.

The tapping depth "

" has not been defined.

Program a cutting pass greater than zero.

9003 'ROUGHING: Value of F=0

DETECTION

CAUSE

SOLUTION

While executing a drilling, facing, taper turning, rounding or profile cycle.

No roughing feedrate "F" has been selected.

Program a positive feedrate "F" other than zero.

9004 'ROUGHING: Value of S=0'

DETECTION

CAUSE

SOLUTION

While executing a drilling, facing, taper turning, rounding or profile cycle.

No roughing spindle speed "S" has been selected.

Program a positive spindle speed "S" other than zero.

9005 'FINISHING: Value of F=0

DETECTION

CAUSE

SOLUTION

While executing a drilling, facing, taper turning, rounding or profile cycle.

No finishing feedrate "F" has been selected.

Program a positive feedrate "F" other than zero.

9006 'FINISHING: Value of S=0'

DETECTION

CAUSE

SOLUTION

While executing a drilling, facing, taper turning, rounding or profile cycle.

No finishing spindle speed "S" has been selected.

Program a positive spindle speed "S" other than zero.

9007 ‘GEOMETRY: Value of Zi=Zf

DETECTION

CAUSE

SOLUTION

While executing a turning, facing, taper turning or grooving cycle.

The Z coordinate of the starting and end points are the same.

The Z coordinate of the starting and end points must be different.

9008 ‘GEOMETRY: Value of X=Ø’

DETECTION

CAUSE

SOLUTION

While executing a turning, facing, taper turning or grooving cycle.

The coordinates of the initial and final diameter are the same.

The X coordinate of the starting and end points must be different from that of the final diameter.

9009 'FINISHING: Impossible finishing stock'

DETECTION

CAUSE

SOLUTION

While executing a turning, facing or grooving cycle.

The finishing stock is greater than the total machining depth.

The finishing stock must be smaller than the total machining depth.

9010 ‘GEOMETRY: Wrong angle value'

DETECTION

CAUSE

SOLUTION

While executing a taper turning cycle.

The taper angle is smaller than 0º or greater than 90º.

The taper angle must be between 0º and 90º.

·T· Model

Ref.1507

·91·

   Error solution

·T· Model

9011 ‘GEOMETRY: Wrong radius value'

DETECTION

CAUSE

SOLUTION

While executing a rounding cycle.

No rounding radius has been defined.

Program a rounding radius other than zero.

9012 'THREADING: Value of T=0'

DETECTION

CAUSE

SOLUTION

While executing a threading cycle.

The tool number has not been defined.

The tool number must be other than zero.

9013 'THREADING: Value of S=0'

DETECTION

CAUSE

SOLUTION

While executing a threading cycle.

The spindle speed "S" has not been defined.

Program a positive spindle speed "S" other than zero.

9014 'THREADING: Value of P=0'

DETECTION

CAUSE

SOLUTION

While executing a threading cycle.

The thread pitch has not been defined.

Program a thread pitch greater than zero.

9015 'THREADING: Value of H=0'

DETECTION

CAUSE

SOLUTION

While executing a threading cycle.

The thread depth has not been defined.

Program a thread depth other than zero.

9016 'THREADING: Value of

D=0’

DETECTION

CAUSE

SOLUTION

While executing a threading cycle.

The tapping depth "

" has not been defined.

Program a cutting pass greater than zero.

9017 'THREADING: Value of s > (Zf-Zi)’

DETECTION

CAUSE

SOLUTION

While executing a threading cycle.

The distance to the end of the thread is greater than the length of the thread.

Program a distance to the end of the thread smaller than the length of the thread.

9018 ‘GEOMETRY: Value of Xi=Xf’

DETECTION

CAUSE

SOLUTION

While executing a threading cycle.

The X coordinate of the starting and end points are the same.

The X coordinate of the starting and end points must be different.

9019 'THREADING: Value of s > (Xf-Xi)’

DETECTION

CAUSE

SOLUTION

While executing a threading cycle.

The distance to the end of the thread is greater than the length of the thread.

Program a distance to the end of the thread smaller than the length of the thread.

9020 'ROUGHING: Wrong location (shape) code’

DETECTION

CAUSE

SOLUTION

While executing a grooving cycle.

No groove roughing can be done with the selected location code.

Select a tool with the right location code.

9021 'FINISHING: Wrong location (shape) code’

DETECTION

CAUSE

SOLUTION

While executing a grooving cycle.

No groove finishing can be done with the selected location code.

Select a tool with the right location code.

Ref.1507

·92·

   Error solution

9022 ‘GEOMETRY: Null profile'

DETECTION

CAUSE

SOLUTION

While executing a level-1 profile cycle.

No profile has been defined because the starting point and the end point are the same.

The starting point and the end point of the profile must be different.

9023 ‘DRILLING: Value of T=0'

DETECTION

CAUSE

SOLUTION

While executing a drilling or multiple drilling cycle.

The tool number has not been defined.

The tool number must be other than zero.

9024 ‘DRILLING: Value of

D=0’

DETECTION

CAUSE

SOLUTION

While executing a drilling or multiple drilling cycle.

The tapping depth "

" has not been defined.

Program a cutting pass greater than zero.

9025 ‘DRILLING: Value of L=0'

DETECTION

CAUSE

SOLUTION

While executing a drilling or multiple drilling cycle.

The drilling depth has not been defined.

Program a drilling depth other than zero.

9026 ‘DRILLING: Value of F=0

DETECTION

CAUSE

SOLUTION

While executing a drilling or multiple drilling cycle.

The feedrate "F" has not been defined.

Program a positive feedrate "F" other than zero.

9027 ‘DRILLING: Value of S=0'

DETECTION

CAUSE

SOLUTION

While executing a drilling or multiple drilling cycle.

The spindle speed "S" has not been defined.

Program a positive spindle speed "S" other than zero.

9028 ‘TAPPING: Value of T=0'

DETECTION

CAUSE

SOLUTION

While executing a tapping or multiple tapping cycle.

The tool number has not been defined.

The tool number must be other than zero.

9029 ‘TAPPING: Value of L=0'

DETECTION

CAUSE

SOLUTION

While executing a tapping or multiple tapping cycle.

The threading depth has not been defined.

Program a tapping depth other than zero.

9030 ‘TAPPING: Value of F=0

DETECTION

CAUSE

SOLUTION

While executing a tapping or multiple tapping cycle.

The feedrate "F" has not been defined.

Program a positive feedrate "F" other than zero.

9031 ‘TAPPING: Value of S=0'

DETECTION

CAUSE

SOLUTION

While executing a tapping or multiple tapping cycle.

The spindle speed "S" has not been defined.

Program a positive spindle speed "S" other than zero.

9032 ‘GEOMETRY: The final diameter is not external’

DETECTION

CAUSE

SOLUTION

While executing a turning or grooving cycle.

An outside turning has been defined, but the final diameter is larger than that of the starting diameter.

In an outside turning, the final diameter must be smaller than the starting one.

·T· Model

Ref.1507

·93·

   Error solution

·T· Model

Ref.1507

9033 ‘GEOMETRY: The final diameter is not internal’

DETECTION

CAUSE

SOLUTION

While executing a turning or grooving cycle.

An inside turning has been defined, but the final diameter is smaller than that of the starting diameter.

In an inside turning, the final diameter must be larger than the starting one.

9034 ‘GEOMETRY: Wrong quadrant’

DETECTION

CAUSE

SOLUTION

While executing a taper turning cycle.

A taper has been defined in the wrong quadrant.

Select the right quadrant using the relevant icon.

9035 ‘A negative safety distance is not allowed in this cycle’

DETECTION

CAUSE

SOLUTION

While executing a taper turning, rounding or profiling cycle.

A negative safety distance has been defined.

In taper canned cycles, the safety distance must be positive.

9036 'ROUGHING: Wrong tool for GROOVING.’

DETECTION

CAUSE

SOLUTION

While executing a grooving cycle.

The geometry of the selected tool is not right for groove roughing.

Select a tool with the right geometry.

9037 'FINISHING: Wrong tool for GROOVING.’

DETECTION

CAUSE

SOLUTION

While executing a grooving cycle.

The geometry of the selected tool is not right for groove finishing.

Select a tool with the right geometry.

9038 ‘GEOMETRY: Wrong angle for GROOVING.’

DETECTION

CAUSE

SOLUTION

While executing a grooving cycle.

The angle of the groove walls is lower than 0º or higher than 90º.

The angle of the groove walls must be between 0º and 90º.

‘GEOMETRY: The sides of the groove intersect each other.’

9039 ‘GEOMETRY: The sides of the groove intersect each other.’

DETECTION

CAUSE

SOLUTION

During execution.

The two walls of the groove intersect each other.

Check the cycle data. The walls of the groove cannot intersect each other.

9040 ‘MULTIPLE CYCLE: Value of b=0’

DETECTION

CAUSE

SOLUTION

While executing a multiple drilling, multiple tapping or slot multiple milling cycle.

The angular step between machining has not been defined.

Program an angular step other than zero.

9041 ‘MULTIPLE CYCLE: Value of N=0'

DETECTION

CAUSE

SOLUTION

While executing a multiple drilling, multiple tapping or slot multiple milling cycle.

The number of machining operations has not been defined.

The minimum number of machining operations is 1.

9042 ‘MULTIPLE SLOT MILLING CYCLE: Value of T=0'

DETECTION

CAUSE

SOLUTION

While executing a multiple slot milling cycle.

The tool number has not been defined.

The tool number must be other than zero.

9043 ‘MULTIPLE SLOT MILLING CYCLE: Value of F=0

DETECTION

CAUSE

SOLUTION

While executing a multiple slot milling cycle.

The feedrate "F" has not been defined.

Program a positive feedrate "F" other than zero.

·94·

   Error solution

9044 ‘MULTIPLE SLOT MILLING CYCLE: Value of S=0'

DETECTION

CAUSE

SOLUTION

While executing a multiple slot milling cycle.

No live tool turning speed "St" has been defined.

Program a positive turning speed "St" other than zero.

9045 ‘MULTIPLE SLOT MILLING CYCLE: Value of I=0'

DETECTION

CAUSE

SOLUTION

While executing a multiple slot milling cycle.

The slot milling depth has not been defined.

Program a slot milling depth other than zero.

9046 ‘MULTIPLE SLOT MILLING CYCLE: Value of L=0'

DETECTION

CAUSE

SOLUTION

While executing a multiple slot milling cycle.

The slot milling length has not been defined.

The slot length must be other than zero.

9048 ‘C AXIS PROFILE CYCLE: Value of T=0'

DETECTION

CAUSE

SOLUTION

While executing a profile cycle on the C axis.

The tool number has not been defined.

The tool number must be other than zero.

9049 ‘C AXIS PROFILE CYCLE: Value of

D=0’

DETECTION

CAUSE

SOLUTION

While executing a profile cycle on the C axis.

The tapping depth "

" has not been defined.

Program a cutting pass greater than zero.

9050 ‘C AXIS PROFILE CYCLE: Value of I=0'

DETECTION

CAUSE

SOLUTION

While executing a profile cycle on the C axis.

The total machining depth has not been defined.

Program a machining depth other than zero.

9051 ‘C AXIS PROFILE CYCLE: Value of F=0

DETECTION

CAUSE

SOLUTION

While executing a profile cycle on the C axis.

The feedrate "F" has not been defined.

Program a positive feedrate "F" other than zero.

9052 ‘C AXIS PROFILE CYCLE: Value of S=0'

DETECTION

CAUSE

SOLUTION

While executing a profile cycle on the C axis.

No live tool turning speed "St" has been defined.

Program a positive turning speed "St" other than zero.

9053 ‘Value of Smax=0’

DETECTION

CAUSE

SOLUTION

While executing any cycle.

The maximum spindle speed "Smax" has not been defined.

Program a maximum positive spindle speed "Smax" other than zero.

9054 ‘DRILLING: Value of K

D>1’

DETECTION

CAUSE

SOLUTION

While executing a drilling or multiple drilling cycle.

The gear ratio "K

" with a value greater than 1.

Program a gear ratio "K

" with a value between 0 and 1.

9055 ‘GEOMETRY: The tool is too big for the groove.’

DETECTION

CAUSE

SOLUTION

While executing a grooving cycle.

The diameter of the selected tool is larger than the width of the programmed groove.

Select another tool with a smaller diameter.

·T· Model

Ref.1507

·95·

   Error solution

·T· Model

Ref.1507

9056 ‘GEOMETRY: Value of Z=R.’

DETECTION

CAUSE

SOLUTION

While executing a grooving cycle.

When milling slots with Z axis penetration (levels 2 and 4), a slot has been programmed without penetration.

Program the external coordinate "Z" and the depth coordinate "R" with different values.

9057 ‘CUTOFF: Value of T=0'

DETECTION

CAUSE

SOLUTION

While executing a cut-off cycle.

The tool number has not been defined.

The tool number must be other than zero.

9058 ‘CUTOFF: Value of F=0

DETECTION

CAUSE

SOLUTION

While executing a cut-off cycle.

The feedrate "F" has not been defined.

Program a positive feedrate "F" other than zero.

9059 ‘CUTOFF: Value of S=0'

DETECTION

CAUSE

SOLUTION

While executing a cut-off cycle.

The spindle speed "S" has not been defined.

Program a positive spindle speed "S" other than zero.

9060 ‘CUTOFF: Value of Fr=0'

DETECTION

CAUSE

SOLUTION

While executing a cut-off cycle.

The cut-off feedrate "Fr" has not been defined.

Program a positive cut-off feedrate "Fr" other than zero.

9061 ‘CUTOFF: Value of Fr > F’

DETECTION

CAUSE

SOLUTION

While executing a cut-off cycle.

The cut-off feedrate "Fr" is higher than the feedrate "F".

Program a smaller cut-off feedrate "Fr" than the feedrate "F".

9062 ‘DRILLING: Value of minimum increment

D’

DETECTION

CAUSE

SOLUTION

While executing a drilling cycle.

The minimum increment is larger than the drilling peck "

"

Program a smaller minimum increment than the drilling peck "

"

9063 ‘TOOL CALIBRATION: Value of T=0'

DETECTION

CAUSE

SOLUTION

While executing a tool calibration cycle.

The tool number has not been defined.

The tool number must be other than zero.

9064 ‘PROBE CALIBRATION: Value of T=0'

DETECTION

CAUSE

SOLUTION

While executing a probe calibration cycle.

The tool number has not been defined.

The tool number must be other than zero.

9065 'RECTANGULAR POCKET: F=0’

DETECTION

CAUSE

SOLUTION

While executing a rectangular pocket cycle.

The feedrate "F" has not been defined.

Program a positive feedrate "F" other than zero.

9066 'RECTANGULAR POCKET: S=0’

DETECTION

CAUSE

SOLUTION

While executing a rectangular pocket cycle.

No live tool turning speed "S" has been defined.

Program a positive spindle speed "S" other than zero.

·96·

   Error solution

9067 'RECTANGULAR POCKET: P=0’

DETECTION

CAUSE

SOLUTION

While executing a rectangular pocket cycle.

The total pocket depth has not been defined.

Program a total pocket depth greater than zero.

9068 'RECTANGULAR POCKET: Wrong penetration angle'

DETECTION

CAUSE

SOLUTION

While executing a rectangular pocket cycle.

The defined penetration angle is wrong.

Program a penetration angle greater than 0º and smaller than or equal to 90º.

9069 'RECTANGULAR POCKET: Tool diameter smaller than

D’

DETECTION

CAUSE

SOLUTION

While executing a rectangular pocket cycle.

The tool diameter is smaller than the maximum roughing pass "

".

The tool diameter must be the same as or larger than the maximum roughing pass "

".

9070 'RECTANGULAR POCKET: Tool diameter larger than pocket'

DETECTION

CAUSE

SOLUTION

While executing a rectangular pocket cycle.

The tool diameter is larger than the pocket.

The tool diameter must be smaller than the pocket’s "L" and "H" dimensions of the pocket.

9071 'RECTANGULAR POCKET: Tool diameter FINISHING STOCK less than d’

DETECTION

CAUSE

SOLUTION

While executing a rectangular pocket cycle.

The diameter of the finishing tool is smaller than the finishing stock "

".

The diameter of the tool must be greater than the finishing stock "

".

9072 'CIRCULAR POCKET: F=0’

DETECTION

CAUSE

SOLUTION

While executing a circular pocket cycle.

The feedrate "F" has not been defined.

Program a positive feedrate "F" other than zero.

9073 'CIRCULAR POCKET: S=0’

DETECTION

CAUSE

SOLUTION

While executing a circular pocket cycle.

No live tool turning speed "S" has been defined.

Program a positive spindle speed "S" other than zero.

9074 'CIRCULAR POCKET: P=0’

DETECTION

CAUSE

SOLUTION

While executing a circular pocket cycle.

The total pocket depth has not been defined.

Program a total pocket depth greater than zero.

9075 'CIRCULAR POCKET: Wrong penetration angle'

DETECTION

CAUSE

SOLUTION

While executing a circular pocket cycle.

The defined penetration angle is wrong.

Program a penetration angle greater than 0º and smaller than or equal to 90º.

9076 'CIRCULAR POCKET: Tool diameter smaller than

D’

DETECTION

CAUSE

SOLUTION

While executing a circular pocket cycle.

The tool diameter is smaller than the maximum roughing pass "

".

The tool diameter must be the same as or larger than the maximum roughing pass "

".

9077 'CIRCULAR POCKET: Tool diameter larger than pocket'

DETECTION

CAUSE

SOLUTION

While executing a circular pocket cycle.

The tool diameter is larger than that of the pocket.

The diameter of the tool must be smaller than the diameter of the pocket (2Rc).

·T· Model

Ref.1507

·97·

·T· Model

Ref.1507

·98·

   Error solution

9078 'CIRCULAR POCKET: Tool diameter FINISHING STOCK less than d’

DETECTION

CAUSE

SOLUTION

While executing a circular pocket cycle.

The diameter of the finishing tool is smaller than the finishing stock "

".

The diameter of the tool must be greater than the finishing stock "

".

9079 'RECTANGULAR POCKET: d not valid’

DETECTION

CAUSE

SOLUTION

While executing a rectangular pocket cycle.

The defined finishing stock "

" is not valid.

Reduce the value of the finishing stock "

".

9080 ‘POSITIONING: Value of T=0'

DETECTION

CAUSE

SOLUTION

While executing a positioning cycle.

The tool number has not been defined.

The tool number must be other than zero.

9081 ‘PROFILE POCKET: F=0’

DETECTION

CAUSE

SOLUTION

While executing a profile pocket cycle.

The feedrate "F" has not been defined.

Program a positive feedrate "F" other than zero.

9082 ‘PROFILE POCKET: S=0’

DETECTION

CAUSE

SOLUTION

While executing a profile pocket cycle.

No live tool turning speed "S" has been defined.

Program a positive spindle speed "S" other than zero.

9083 ‘PROFILE POCKET: Wrong penetration angle'

DETECTION

CAUSE

SOLUTION

While executing a profile cycle.

The defined penetration angle is wrong.

Program a penetration angle greater than 0º and smaller than or equal to 90º.

9084 ‘PROFILE POCKET: Tool diameter smaller than

D’

DETECTION

CAUSE

SOLUTION

While executing a profile pocket cycle.

The tool diameter is smaller than the maximum roughing pass "

".

The tool diameter must be the same as or larger than the maximum roughing pass "

".

9085 ‘PROFILE POCKET: Tool diameter FINISHING STOCK less than d’

DETECTION

CAUSE

SOLUTION

While executing a profile pocket cycle.

The diameter of the finishing tool is smaller than the finishing stock "

".

The diameter of the tool must be greater than the finishing stock "

".

9081 ‘PROFILE POCKET: P=0’

DETECTION

CAUSE

SOLUTION

While executing a profile pocket cycle.

The total pocket depth has not been defined.

Program a total pocket depth greater than zero.

   Error solution

·T· Model

Ref.1507

·99·

   Error solution

·T· Model

Ref.1507

·100·