INSTALLATION. Ignis AKP 120/01 WH, AKS150/IX/02, AKP 229/01 IX, AKP 135/05 NB, AKP 235/01 WH, AKS 149/02 JA, AKP 202/IX, AKP 233 WH, AKP 233 IX, AKP 102/AP/03


Add to my manuals
10 Pages

advertisement

INSTALLATION. Ignis AKP 120/01 WH, AKS150/IX/02, AKP 229/01 IX, AKP 135/05 NB, AKP 235/01 WH, AKS 149/02 JA, AKP 202/IX, AKP 233 WH, AKP 233 IX, AKP  102/AP/03 | Manualzz

INSTALLATION

Recommendations

IMPORTANT: Disconnect the oven from the mains before carrying out any installation work or servicing.

Installation must be carried out by a qualified technician in accordance with the manufacturer’s instructions and in compliance with local regulations.

Unpack the oven and make sure that the oven has not been damaged during transport and that the oven door closes properly. If you are not sure contact the dealer or the nearest service centre.

After removing the oven from its packaging, leave it on the polystyrene base to prevent it from being damaged.

When installing the oven it is advisable to wear protective gloves.

The oven is provided with two side handles (B) to facilitate installation (fig. 7).

Preparing the housing unit

Kitchen units in contact with the oven must be heat resistant (80°C min).

Cut the kitchen unit and worktop to fit before installing the oven. Carefully remove any shavings or sawdust that could prevent the oven from running properly.

The dimensions of the housing units in which the oven can be installed are shown in figures 1, 2 and 3.

The dimensions of the oven are shown in figure 4.

To allow for proper ventilation, an opening should be left at the bottom of the housing unit. Pay attention to the dimensions. The bottom of the oven must not be accessible after installation.

During installation make sure that the sides of the oven do not touch the adjacent units.

2 3

1

4

85

For ovens installed under the worktop, leave a minimum clearance of 5 mm between the upper edge of the oven and the lower edge of the worktop (fig. 5). For correct operation of the appliance, this clearance must always be unobstructed.

If the kitchen unit is not securely fixed to the wall, it must be anchored with standard brackets (A)

(fig. 6).

Electrical connection

Regulations require that the appliance be earthed.

Connection to the mains must be carried out by a qualified electrician in accordance with the manufacturer’s instructions and in compliance with local regulations.

The installer is responsible for connecting appliances correctly to the mains and for observing the safety regulations.

The oven power cable must be long enough to connect the built-in oven to the mains.

Observance of safety directives requires that an accessible mains disconnection device or a multi-pole switch with a minimum contact gap of 3mm be used for the installation.

Do not use multiple plug adapters or extension leads.

After the oven has been installed, the electrical components must be inaccessible.

5

86

6

Connecting the oven to the power supply

Make sure that the voltage indicated on the rating plate is the same as the mains voltage.

The rating plate is on the front edge of the oven (visible when the door is open).

If the power cable is not present proceed as follows:

1. Remove the two fastening screws of the terminal box cover located on the bottom part of the oven’s rear covering.

2. Remove the cover to gain access to the terminal box and insert the power cable (see table) through the opening located on the bottom of the oven.

Power supply cable table

N° of conductors Type of cable

H05 RR-F 3 X 1.5 mm²

3. Connect the cable to the terminal box, tighten the screws as far as they will go and secure it to the cable fastener.

4. Put the cover back on by inserting the two blades in the slots and fasten it with the two screws.

Securing the oven

Lift up the oven getting hold of it by the handles (B) unit, being careful not to trap the power supply cable (fig. 8).

on the sides and insert it into the housing

Center the oven in the housing unit before securing it.

The oven comes with spacers already fitted to facilitate the anchoring of the oven to the housing unit with the screws provided (as shown in fig. 9).

7

8

87

9

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Questions & Answers

2024-05-22

E E C

How to install the oven?
Refer to the manual for detailed installation instructions.
How to connect the oven electrically?
The electrical connection must be performed by a qualified electrician following safety regulations.
What precautions to take when using the oven?
Keep children away from hot surfaces, use oven gloves, and avoid using synthetic material containers for cooking.

Related manuals

advertisement