Maintenance and care. Mercedes-Benz CLS 550 BlueEFFICIENCY, 2013 CLS Coupe, 2013, CLS, CLS Series
Advertisement
Advertisement
298
Engine compartment
Useful information i This Operator's Manual describes all models and all standard and optional equipment of your vehicle available at the time of publication of the Operator's
Manual. Country-specific differences are possible. Please note that your vehicle may not be equipped with all features described. This also applies to safetyrelated systems and functions.
i Read the information on qualified specialist workshops: ( Y page 24).
Engine compartment
Hood
Opening the hood
G WARNING
Do not pull the release lever while the vehicle is in motion. Otherwise, the hood could be forced open by passing air flow.
This could cause the hood to come loose and injure you and/or others.
G WARNING
Do not open the hood when the engine is overheated. You could be seriously injured.
Observe the coolant temperature gauge to determine whether the engine may be overheated. If you see flames or smoke coming from the engine compartment, move away from the vehicle. Wait until the engine has cooled. If necessary, call the fire department.
G WARNING
There is a risk of injury if the hood is open, even if the engine is not running.
Some engine components can become very hot.
To avoid the risk of burns, only touch those components described in the Operator's
Manual and observe the relevant safety notes.
G WARNING
To avoid injury, stay clear of moving parts when the hood is open and the engine is running.
The radiator fan may continue to run for approximately 30seconds or may even restart after the engine has been switched off. For this reason, you must not reach into the fan rotation area.
G WARNING
The engine is equipped with a transistorized ignition system. Because of the high voltage, it is dangerous to touch any components
(ignition coils, spark plug sockets, diagnostic socket) of the ignition system:
R with the engine running
R while starting the engine
R when the ignition is switched on and the engine is turned manually
G WARNING
The windshield wipers and wiper linkage could be set in motion.
When the hood is open, you or others could be injured by the wiper linkage.
Make sure that the windshield wipers are switched off. Remove the SmartKey or make sure that no ignition position has been selected with KEYLESS-GO. All indicator lamps must be off in the instrument panel.
! Make sure that the windshield wipers are not folded away from the windshield. You could otherwise damage the windshield wipers or the hood.
Engine compartment
299
X
X
Lower the hood and let it fall from a height of approximately 8 inches (20cm).
Check that the hood has engaged properly.
If the hood can be raised slightly, it is not properly engaged. Open it again and close it with a little more force.
X Make sure that the windshield wipers are turned off.
X Pull release lever : on the hood.
The hood is released.
X Reach into the gap, pull hood catch handle ; up and lift the hood.
If you lift the hood approximately
15 inches (40 cm), the hood is opened and held open automatically by the gas-filled struts.
Engine oil
General notes
Depending on the driving style, the vehicle consumes up to 0.9 US qt (0.8 liters) of oil over a distance of 600 miles (1,000 km). The oil consumption may be higher than this when the vehicle is new or if you frequently drive at high engine speeds.
Depending on the engine, the oil dipstick may be in a different location.
When checking the oil level:
R park the vehicle on a level surface.
R the engine should be switched off for approximately five minutes if the engine is at normal operating temperature.
R if the engine is not at normal operating temperature, e.g. if the engine was only started briefly: wait about 30 minutes before carrying out the measurement.
Checking the oil level using the oil dipstick
Closing the hood
G WARNING
When closing the hood, use extreme caution not to catch hands or fingers. Be careful that you do not close the hood on anyone.
Make sure the hood is securely engaged before driving off. Do not continue driving if the hood can no longer engage after an accident, for example. The hood could otherwise come loose while the vehicle is in motion and injure you and/or others.
X
X
Pull oil dipstick : out of the dipstick guide tube.
Wipe off oil dipstick :.
Z
300
Engine compartment
X Slowly slide oil dipstick : into the guide tube to the stop, and take it out again.
If the level is between MIN mark = and
MAX mark ;, the oil level is correct.
X If the oil level has dropped to MIN mark
= or below, add 1.1 US qt (1.0 liter) of engine oil.
Adding engine oil
G WARNING
If engine oil comes into contact with hot engine parts, it may ignite and you could burn yourself. Do not spill any engine oil on hot engine parts.
H Environmental note
When adding oil, take care not to spill any. If oil enters the soil or waterways, it is harmful to the environment.
! Only use engine oils and oil filters that have been approved for vehicles with a service system. You can obtain a list of the engine oils and oil filters tested and approved in accordance with the
Mercedes-Benz Specifications for Service
Products at any Mercedes-Benz Service center.
Damage to the engine or exhaust system is caused by the following:
R using engine oils and oil filters that have not been specifically approved for the service system
R replacing engine oil and oil filters after the interval for replacement specified by the service system has been exceeded
R using engine oil additives.
! Do not add too much oil. adding too much engine oil can result in damage to the engine or to the catalytic converter. Have excess engine oil siphoned off.
Example: engine oil cap
X Turn cap : counter-clockwise and remove it.
X Add engine oil.
If the oil level is at or below the MIN mark on the oil dipstick, add 1.1 US qt (1.0 liter) of engine oil.
X Replace cap : on the filler neck and turn clockwise.
Ensure that the cap locks into place securely.
X Check the oil level again with the oil dipstick ( Y page 299).
Further information on engine oil
( Y page 368).
Additional service products
Checking the coolant level
G WARNING
In order to avoid any potentially serious burns:
R use extreme caution when opening the hood if there are any signs of steam or coolant leaking from the cooling system, or if the coolant temperature display indicates that the coolant is overheated.
R do not remove the pressure cap on the coolant reservoir if the coolant temperature is above 158 ‡ (70 †). Allow the engine to cool down before removing the cap. The coolant reservoir contains hot fluid and is under pressure.
Engine compartment
301
R using a rag, slowly turn the cap approximately 1 /
2
turn to relieve excess pressure. If opened immediately, scalding hot fluid and steam will be blown out under pressure.
R do not spill antifreeze on hot engine parts.
Antifreeze contains ethylene glycol which may burn if it comes into contact with hot engine parts.
neck when warm, there is enough coolant in coolant expansion tank ;.
X If necessary, add coolant that has been tested and approved by Mercedes-Benz.
X Replace cap : and turn it clockwise as far as it will go.
For further information on coolant, see
( Y page 369).
Adding washer fluid to the windshield washer system/headlamp cleaning system
G WARNING
Washer solvent/antifreeze is highly flammable. Do not spill washer solvent/ antifreeze on hot engine parts, because it may ignite and burn. You could be seriously burned.
X Park the vehicle on a level surface.
Only check the coolant level when the vehicle is on a level surface and the engine has cooled down.
X
X
X
X
X
Turn the SmartKey to position 2 in the ignition lock ( Y page 139).
On vehicles with KEYLESS-GO, press the
Start/Stop button twice ( Y page 139).
Check the coolant temperature display in the instrument cluster.
The coolant temperature must be below
158 ‡ (70 †).
Turn the SmartKey to position
0 ( Y page 139) in the ignition lock.
Slowly turn cap : half a turn counterclockwise to allow excess pressure to escape.
Turn cap : further counter-clockwise and remove it.
If the coolant is at the level of marker bar
= in the filler neck when cold, there is enough coolant in coolant expansion tank ;.
If the coolant level is approximately 0.6 in
(1.5 cm) above marker bar = in the filler
X To open: pull cap : upwards by the tab.
X Add the premixed washer fluid.
X To close: press cap : onto the filler neck until it engages.
The washer fluid reservoir is used for both the windshield washer system and the headlamp cleaning system.
Further information on windshield washer fluid/antifreeze ( Y page 370).
Z
302
Maintenance
Maintenance
ASSYST PLUS
Service messages
The ASSYST PLUS service interval display informs you of the next service due date.
Information on the type of service and service intervals (see separate Service Booklet).
You can obtain further information from an authorized Mercedes-Benz Center or at http://www.mbusa.com (USA only).
i The ASSYST PLUS service interval display does not show any information on the engine oil level. Observe the notes on the engine oil level ( Y page 299).
The multifunction display shows a service message for several seconds, e.g.:
Next Service A in .. days
Service A Due
Service A Exceeded by ... days
The letter A or B , possibly in connection with a number or another letter, shows the type of service. A stands for a minor service and B for a major service.
You can obtain further information from an authorized Mercedes-Benz Center.
The ASSYST PLUS service interval display does not take into account any periods of time during which the battery is disconnected.
Maintaining the time-dependent service schedule:
X Note down the service due date displayed in the multifunction display before disconnecting the battery.
or
X After reconnecting the battery, subtract the battery disconnection periods from the service date shown on the display.
Hiding a service message
X Press the % or a button on the steering wheel.
Displaying service messages
X Switch on the ignition.
X
X
Press the = or ; button on the steering wheel to select the Serv.
menu.
Press the 9 or : button to select the
ASSYST PLUS submenu and confirm with a.
The service due date appears in the multifunction display.
Information about Service
Resetting the ASSYST PLUS service interval display
! If the ASSYST PLUS service interval display has been inadvertently reset, this setting can be corrected at a qualified specialist workshop.
Have service work carried out as described in the Maintenance Booklet. This may otherwise lead to increased wear and damage to the major assemblies or the vehicle.
A qualified specialist workshop, e.g. an authorized Mercedes-Benz Center, will reset the ASSYST PLUS service interval display after the service work has been carried out.
You can also obtain further information on maintenance work, for example.
Special service requirements
Arduous operating conditions or increased loads on the vehicle will require some service work to be performed more often than for a vehicle in normal use. Such arduous conditions include regular city driving with frequent intermediate stops and use in mountainous terrain or on poor road surfaces.
For example, if the vehicle is used under arduous operating conditions, have air filters,
Care
303 engine oil and oil filters changed frequently and check the wheels often. Further information can be obtained at a qualified specialist workshop, e.g. an authorized
Mercedes-Benz Center.
Driving abroad
An extensive Mercedes-Benz Service network is also available in other countries. You can obtain further information from any authorized Mercedes-Benz Center.
! Do not park the vehicle for an extended period straight after cleaning it, particularly after having cleaned the wheels with wheel cleaner. Wheel cleaners could cause increased corrosion of the brake discs and brake pads/linings. For this reason, you should drive for a few minutes after cleaning. Braking heats the brake discs and the brake pads/linings, thus drying them.
The vehicle can then be parked.
Regular care of your vehicle is a condition for retaining the quality in the long term.
Use care products and cleaning agents recommended and approved by Mercedes-
Benz.
Care
General notes
G WARNING
Many cleaning products can be hazardous.
Some are poisonous, others are flammable.
Always follow the instructions on the particular container. Always open your vehicle's doors or windows when cleaning the inside.
Never use fluids or solvents that are not designed for cleaning your vehicle.
Always lock away cleaning products and keep them out of reach of children.
H Environmental note
Dispose of empty packaging and cleaning cloths in an environmentally responsible manner.
! For cleaning your vehicle, do not use any of the following:
R dry, rough or hard cloths
R abrasive cleaning agents
R solvents
R cleaning agents containing solvents
Do not scrub.
Do not touch the surfaces or protective films with hard objects, e.g. a ring or ice scraper. You could otherwise scratch or damage the surfaces and protective film.
Washing the vehicle and cleaning the paintwork
Automatic car wash
G WARNING
Braking efficiency is reduced after washing the vehicle. This could cause an accident. For this reason, you must drive particularly carefully after washing the vehicle until the brakes have dried.
G WARNING
The vehicle is braked when the HOLD function or DISTRONIC PLUS is activated. Therefore, deactivate the HOLD function and DISTRONIC
PLUS before the vehicle is washed in an automatic car wash.
! Never clean your vehicle in a Touchless
Automatic Car Wash as these use special cleaning agents. These cleaning agents can damage the paintwork or plastic parts.
! Make sure that:
Z
304
Care
R the side windows and the sliding sunroof are fully closed.
R the ventilation/heating is switched off
(the OFF button has been pressed).
R the windshield wiper switch is in position
0.
Otherwise, the vehicle might be damaged.
! In car washes with a towing mechanism, make sure that the automatic transmission is in transmission position N, otherwise the vehicle could be damaged.
R
Vehicles with a SmartKey:
Do not remove the SmartKey from the ignition lock. Do not open the driver's door or front-passenger door when the engine is switched off. Otherwise, the automatic transmission selects park position P automatically and locks the wheels. You can prevent this by shifting the automatic transmission to N beforehand.
R
Vehicles with KEYLESS-GO:
Do not open the driver's door or frontpassenger door when the engine is switched off. Otherwise, the automatic transmission selects park position P automatically and locks the wheels.
Observe the following to make sure that the automatic transmission stays in position N:
X Make sure the vehicle is stationary and the ignition is switched off.
X Turn the SmartKey to position
2 ( Y page 139) in the ignition lock.
Use the SmartKey instead of the Start/
Stop button on vehicles with KEYLESS-GO.
X
X
X
X
X
Depress and hold the brake pedal.
Shift the automatic transmission to position N.
Release the brake pedal.
Release the electric parking brake.
Switch off the ignition and leave the
SmartKey in the ignition lock.
You can wash the vehicle in an automatic car wash from the very start.
If the vehicle is very dirty, pre-wash it before cleaning it in an automatic car wash.
After using an automatic car wash, wipe off wax from the windshield and the wiper blades. This will prevent smears and reduce wiping noises caused by residue on the windshield.
Washing by hand
In some countries, washing by hand is only allowed at specially equipped washing bays.
Observe the legal requirements in all countries concerned.
X Do not use hot water and do not wash the vehicle in direct sunlight.
Use a soft sponge to clean.
X
X
X
Use a mild cleaning agent, such as a car shampoo approved by Mercedes-Benz.
Thoroughly hose down the vehicle with a gentle jet of water.
X Do not point the water jet directly towards the air inlet.
X Use plenty of water and rinse out the sponge frequently.
X Rinse the vehicle with clean water and dry thoroughly with a chamois.
X Do not let the cleaning agent dry on the paintwork.
When using the vehicle in winter, remove all traces of road salt deposits carefully and as soon as possible.
Power washers
G WARNING
Do not use power washers with circular-jet nozzles (dirt grinders) to clean your vehicle, in particular the tires. You could otherwise damage the tires and cause an accident.
! Always maintain a distance of at least
11.8 in (30 cm) between the vehicle and the power washer nozzle. Information about the correct distance is available from the equipment manufacturer.
Care
305
Move the power washer nozzle around when cleaning your vehicle.
Do not aim directly at any of the following:
R tires
R door gaps, roof gaps, joints, etc.
R electrical components
R battery
R connectors
R lights
R seals
R trim
R ventilation slots
Damaged seals or electrical components can lead to leaks or failures.
Benz. This is the case approximately every three to five months, depending on the climate conditions and the care product used.
If dirt has penetrated the paint surface or if the paint has become dull, the paint cleaner recommended and approved by Mercedes-
Benz should be used.
Do not use these care products in the sun or on the hood while the hood is hot.
X Use a suitable touch-up stick, e.g. MB
Touch-Up Stick, to repair slight damage to the paintwork quickly and provisionally.
Cleaning the paintwork
! Do not affix:
R stickers
R films
R magnetic plates or similar items to painted surfaces. You could otherwise damage the paintwork.
Scratches, corrosive deposits, areas affected by corrosion and damage caused by inadequate care cannot always be completely repaired. In such cases, visit a qualified specialist workshop.
X Remove dirt immediately, where possible, while avoiding rubbing too hard.
X Soak insect remains with insect remover and rinse off the treated areas afterwards.
X Soak bird droppings with water and rinse off the treated areas afterwards.
X Remove coolant, brake fluid, tree resin, oils, fuels and greases by rubbing gently with a cloth soaked in petroleum ether or lighter fluid.
X
X
Use tar remover to remove tar stains.
Use silicone remover to remove wax.
If water no longer forms "beads" on the paint surface, use the paint care products recommended and approved by Mercedes-
Matte finish care
! Never polish the vehicle or the light alloy wheels. Polishing causes the finish to shine.
! The following may cause the paint to become shiny and thus reduce the matte effect:
R
Vigorous rubbing with unsuitable materials.
R
Frequent use of car washes.
R
Washing the vehicle in direct sunlight.
! Never use paint cleaner, buffing or polishing products, or gloss preserver, e.g.
wax. These products are only suitable for high-gloss surfaces. Their use on vehicles with matte finish leads to considerable surface damage (shiny, spotted areas).
Always have paintwork repairs performed at a qualified specialist workshop, e.g. an authorized Mercedes-Benz Center.
! Do not use wash programs with a hot wax treatment under any circumstances.
Observe these notes if your vehicle has a clear matte finish. This will help you to avoid damage to the paintwork due to incorrect treatment.
These notes also apply to light alloy wheels with a clear matte finish.
Z
306
Care i The vehicle should preferably be washed by hand using a soft sponge, car shampoo and plenty of water.
i Use only insect remover and car shampoo from the range of recommended and approved Mercedes-Benz care products.
intervals. Deposits such as leaves, petals and pollen may under certain circumstances prevent water from draining away. This can lead to corrosion damage and damage to electronic components.
X Clean the inside and outside of the windows with a damp cloth and a cleaning agent that is recommended and approved by Mercedes-Benz.
Cleaning the vehicle parts
Cleaning the wheels
! Do not use acidic wheel cleaning products to remove brake dust. This could damage wheel bolts and brake components.
! Do not park the vehicle for an extended period straight after cleaning it, particularly after having cleaned the wheels with wheel cleaner. Wheel cleaners could cause increased corrosion of the brake discs and brake pads/linings. For this reason, you should drive for a few minutes after cleaning. Braking heats the brake discs and the brake pads/linings, thus drying them.
The vehicle can then be parked.
Cleaning the windows
G WARNING
Before cleaning the windshield or wiper blades, switch off the windshield wipers and remove the SmartKey from the ignition lock.
On vehicles with KEYLESS-GO, press the
Start/Stop button repeatedly until all indicator lamps in the instrument cluster have gone out. The windshield wipers could otherwise move and injure you.
! Do not use dry cloths, abrasive products, solvents or cleaning agents containing solvents to clean the inside of the windows.
Do not touch the insides of the windows with hard objects, e.g. an ice scraper or ring. There is otherwise a risk of damaging the windows.
! Clean the water drainage channels of the windshield and the rear window at regular
Cleaning the wiper blades
G WARNING
Before cleaning the windshield or wiper blades, switch off the windshield wipers and remove the SmartKey from the ignition lock.
On vehicles with KEYLESS-GO, press the
Start/Stop button repeatedly until all indicator lamps in the instrument cluster have gone out. The windshield wipers could otherwise move and injure you.
! Do not pull the wiper blade. Otherwise, the wiper blade could be damaged.
! Do not clean wiper blades too often and do not rub them too hard. Otherwise, the graphite coating could be damaged. This could cause wiper noise.
! Hold the wiper arm securely when folding back. The windshield could be damaged if the wiper arm smacks against it suddenly.
X
X
X
Fold the windshield wiper arms away from the windshield.
Carefully clean the wiper blades with a damp cloth.
Fold the windshield wiper arms back again before switching on the ignition.
Cleaning the exterior lighting
! Only use cleaning agents or cleaning cloths which are suitable for plastic light lenses. Unsuitable cleaning agents or cleaning cloths could scratch or damage the plastic light lenses.
Care
307
X Clean the plastic lenses of the exterior lighting using a wet sponge and a mild cleaning agent, e.g. Mercedes-Benz car shampoo or cleaning cloths.
Cleaning the rear view camera
! Do not clean the camera lens and the area around the rear view camera with a power washer.
Mirror turn signals
! Only use cleaning agents or cleaning cloths that are suitable for plastic lenses.
Unsuitable cleaning agents or cleaning cloths could scratch or damage the plastic lenses of the mirror turn signals.
X Clean the plastic lenses of the mirror turn signals in the exterior mirror housing using a wet sponge and mild cleaning agent, e.g.
Mercedes-Benz car shampoo or cleaning cloths.
X Use clear water and a soft cloth to clean camera lens :.
Cleaning the sensors
! If you clean the sensors with a power washer, make sure that you keep a distance of at least 11.8 in (30 cm) between the vehicle and the power washer nozzle.
Information about the correct distance is available from the equipment manufacturer.
Cleaning the exhaust pipes
! Do not clean the exhaust pipe with alkaline-based cleaning agents, such as wheel cleaner.
Impurities combined with the effects of road grit and corrosive environmental factors may cause flash rust to form on the surface. You can restore the original shine of the exhaust pipe by cleaning it regularly, especially in winter and after washing.
X Clean the exhaust pipe with a chrome care product tested and approved by Mercedes-
Benz.
X Clean sensors : of the driving systems with water, car shampoo and a soft cloth.
Interior care
Cleaning the display
! For cleaning, do not use any of the following:
R alcohol-based thinner or gasoline
R abrasive cleaning agents
R commercially-available household cleaning agents
These may damage the display surface. Do not put pressure on the display surface
Z
308
Care when cleaning. This could lead to irreparable damage to the display.
X
X
Before cleaning the display, make sure that it is switched off and has cooled down.
Clean the display surface using a commercially available microfiber cloth and TFT/LCD display cleaner.
X Dry the display surface using a dry microfiber cloth.
Cleaning Night View Assist Plus
G WARNING
Always remember that your primary responsibility is to drive the vehicle. The driver must always concentrate on the road. For your safety and the safety of others, stop the vehicle before trying to clean fogged-up windows or to clean the window in front of the
Night View Assist Plus camera.
Bear in mind that at a speed of only 30 mph
(approximately 50 km/h), the vehicle covers a distance of 44 feet (approximately 14 m) per second.
! Never clean the camera lens. When cleaning the field of vision of the driving systems, make sure that you do not spray glass cleaner on the camera lens. If the camera lens is dirty, visit a qualified specialist workshop.
X Fold down the camera cover by recess :.
X Use a soft cloth to clean the windshield in front of camera ;.
Cleaning the plastic trim
G WARNING
When cleaning the steering wheel boss and dashboard, do not use cockpit sprays or cleaning agents containing solvents. Cleaning agents containing solvents cause the surface to become porous, and as a result, plastic parts may break away and be thrown around the interior when an air bag is deployed, which may result in severe injuries.
! Do not affix the following to plastic surfaces:
R stickers
R films
R scented oil bottles or similar items
You can otherwise damage the plastic.
! Do not allow cosmetics, insect repellent or sunscreen to come into contact with the plastic trim. This maintains the high-quality look of the surfaces.
X
X
Wipe the plastic trim with a damp, lint-free cloth, e.g. a microfiber cloth.
Heavy soiling: use car care and cleaning products recommended and approved by
Mercedes-Benz.
The surface may change color temporarily.
Wait until the surface is dry again.
Care
309
Cleaning the steering wheel and gear or selector lever
X Thoroughly wipe with a damp cloth or use leather care agents that have been recommended and approved by Mercedes-
Benz.
Cleaning genuine wood and trim elements
! Do not use solvent-based cleaning agents such as tar remover, wheel cleaners, polishes or waxes. There is otherwise a risk of damaging the surface.
! Do not use chrome polish on trim pieces.
The trim pieces have a chrome look but are mostly made of anodized aluminum and can lose their shine if chrome polish is used. Use a damp, lint-free cloth instead when cleaning the trim pieces.
If the chrome-plated trim pieces are very dirty, you can use a chrome polish. If you are unsure as to whether the trim pieces are chrome-plated or not, consult an authorized Mercedes-Benz Center.
X
X
Wipe the wooden trim and trim pieces with a damp, lint-free cloth, e.g. a microfiber cloth.
Heavy soiling: use car care and cleaning products recommended and approved by
Mercedes-Benz.
obtain these from a qualified specialist workshop.
R clean artificial leather covers with a cloth moistened with a solution containing 1% detergent (e.g. dish washing liquid).
R clean cloth covers with a microfiber cloth moistened with a solution containing 1% detergent (e.g. dish washing liquid). Rub carefully and always wipe entire seat sections to avoid leaving visible lines.
Leave the seat to dry afterwards.
Cleaning results depend on the type of dirt and how long it has been there.
R clean DINAMICA covers with a damp cloth. Make sure that you wipe entire seat sections to avoid leaving visible lines.
! Do not use microfiber cloths to clean genuine leather, artificial leather or
DINAMICA covers. If used often, these can damage the cover.
i Note that regular care is essential to ensure that the appearance and comfort of the covers is retained over time.
Cleaning the seat covers
! Observe the following when cleaning:
R clean genuine leather covers carefully with a damp cloth and then wipe the covers down with a dry cloth. Make sure that the leather does not become soaked. It may otherwise become rough and cracked. Only use leather care agents that have been tested and approved by Mercedes-Benz. You can
Cleaning the seat belts
G WARNING
Do not bleach or dye seat belts as this may severely weaken them. In a crash, they may not be able to provide adequate protection.
! Do not clean the seat belts using chemical cleaning agents. Do not dry the seat belts by heating at temperatures above 176 ‡
(80 †) or in direct sunlight.
X Use clean, lukewarm water and soap solution.
Cleaning the headliner and carpets
X
X
Headliner: if it is very dirty, use a soft brush or dry shampoo.
Carpets: use the carpet and textile cleaning agents recommended and approved by Mercedes-Benz.
Z
310
Useful information ............................ 312
Where will I find...? ........................... 312
Flat tire .............................................. 313
Battery (vehicle) ................................ 314
Jump-starting .................................... 317
Towing and tow-starting .................. 318
Fuses .................................................. 322
311

Public link updated
The public link to your chat has been updated.
Advertisement