Power Requirements. Sundance Spas 680™ Series

Power Requirements. Sundance Spas 680™ Series

Add to My manuals
58 Pages

Sundance Spas 680™ Series is a line of luxury spas designed to provide relaxation and rejuvenation. It features advanced water filtration and purification systems to ensure clean and healthy water. The spas are also equipped with a variety of massage jets and lighting options to customize your spa experience. With its sleek design and durable construction, the Sundance Spas 680™ Series is the perfect addition to any home.

advertisement

Power Requirements. Sundance Spas 680™ Series | Manualzz

680 SERIES

5.0 Power Requirements

Sundance ® spas are designed to provide optimum performance and flexibility of use when connected to the

maximum electrical service listed on pages 12-14. If

you prefer, your dealer can perform a minor circuit board modification to allow your spa to accept an electrical service other than the factory setting.

Note: Refer to pages 47-50 for circuit board configuration details or

contact your authorized Sundance dealer.

5.1 North American 60 Hz Power Options

North American Denali/Tacoma 1-Pump Convertible Models (60 Hz)

120V/15A* 240V/30A* 240V/40A**

Voltage: 120 VAC 240 VAC 240 VAC

# of Wires:

Frequency:

Current Draw:

Circuit Breaker:

3 (15A GFCI Cord -

US Models Only*)

60 Hz

12A

15A, 1-Pole

4 (Hard

Wired Only)

60 Hz

21A

30A, 2-Pole

4 (Hard

Wired Only)

60 Hz

30A

40A, 2-Pole

CAUTION (For 4-wire, 240 VAC Heater Operation): Move the red wire on the main terminal strip (TB1) from position #1 to position #3. Make certain wires are

connected exactly as shown in Figure D (page 17) before applying power.

Failure to do so will result in damage to the circuit board and/or related components and void the manufacturer’s warranty.

* In the 15A/30A configuration, the heater will not operate at the same time as the high-speed jets pump. The factory setting is 120V/15A.

** If the spa is to be operated on 40A service, remove the jumper JP1 #1-2 on the circuit board to allow the heater to operate at the same time as the

high-speed jets pump (page 47).

Page 12

advertisement

Key Features

  • Advanced water filtration and purification systems
  • Variety of massage jets and lighting options
  • Sleek design and durable construction
  • Automated filtration and heating cycles
  • Optional BLUEWAVE® Spa Stereo System
  • Multi-colored LED light system
  • CLEARRAY® Water Purification System

Frequently Answers and Questions

What are the water chemistry parameters for Sundance Spas 680™ Series?
With CLEARRAY®: pH 7.4-7.6, Free chlorine no less than 1.0 ppm, Free Bromine no less than 2.0 ppm, Total Alkalinity 100-150 ppm, Calcium Hardness 150-250 ppm. Without CLEARRAY®: pH 7.4-7.6, Free chlorine 3.0-4.0 ppm, Free Bromine 2.0-4.0 ppm, Total Alkalinity 100-150 ppm, Calcium Hardness 150-250 ppm.
How often should I clean the filter cartridges?
Every month or as needed.
How often should I replace the spa's water?
Every 3 months or when you cannot control sudsing or get the normal feel or sparkle to the water.
What are the different filtration/heating modes?
Standard Filtration/Heating Modes (F1-F3) and Economy Filtration/Heating Modes (F4-F6).
How do I select the desired massage action?
Use the Massage button to cycle through the different massage options.

Related manuals

Download PDF

advertisement

Table of contents