OSD (On-Screen-Display) Controls. NEC MultiSync V652-TM

Add to My manuals
48 Pages

advertisement

OSD (On-Screen-Display) Controls. NEC MultiSync V652-TM | Manualzz

OSD (On-Screen-Display) Controls

NOTE: Some functions may not be available depending on the model or optional equipment.

Input source

Main Menu Icons

Main Menu Item

Sub Menu

PICTURE MODE

Select

70

50

50

50

50

THANK YOU FOR SAVING

THE ENVIRONMENT.

CARBON FOOTPRINT 86.0 %

Goto Adjustment Return Close

Key Guide

Adjustment Settings

Press UP or DOWN button to select sub-menu.

Press SET.

Press UP or DOWN,

PLUS or MINUS to select the function or setting to be adjusted.

Press MENU or EXIT.

Remote Control

Press UP or DOWN button to select.

Press INPUT button to decide.

Press UP or DOWN, PLUS or MINUS button to select.

Press EXIT

Control Panel

OSD screen

English-21

Setting

PICTURE

BACKLIGHT

Default

CONTRAST

SHARPNESS

BRIGHTNESS

DICOM SIM.

PROGRAMMABLE

MOVIE SETTINGS

NOISE REDUCTION

VIDEO1, VIDEO2, S-VIDEO inputs only

Adjusts the overall image and background brightness. Press + or - to adjust.

Note: When AMBIENT1 or AMBIENT2 is selected in picture mode, this function cannot be changed.

Adjusts the image brightness in relationship to the input signal. Press + or - to adjust.

Note: When sRGB is selected in picture mode, this function cannot be changed.

Adjusts the crispness of the image. Press + or - to adjust.

Adjusts the image brightness in relationship to the background. Press + or - to adjust.

Note: When sRGB is selected in picture mode, this function cannot be changed.

Depends on destination

50*

50

HUE

COLOR

Adjusts the hue of the screen. Press + or - to adjust.

Note: When sRGB is selected in picture mode, this function cannot be changed.

Adjusts the color depth of the screen. Press + or - to adjust.

Note: When sRGB is selected in picture mode, this function cannot be changed.

COLOR TEMPERATURE Adjusts the color temperature of the entire screen. A low color temperature will make the screen reddish. A high color temperature will make the screen bluish. If TEMPERATURE needs further adjustment, the individual R/G/B/ levels of the white point can be adjusted. To adjust the R/G/B levels, CUSTOM must be showing as the COLOR TEMP selection.

Note: When sRGB is selected in picture mode, predefi ned 6500k is set so it cannot be changed.

When PROGRAMMABLE is selected in GAMMA CORRECTION, this function cannot be changed.

COLOR CONTROL Adjusts the hue of the Red, Yellow, Green, Cyan, Blue and Magenta.

Note: When sRGB is selected in picture mode, this function cannot be changed.

GAMMA CORRECTION Select a display gamma for best picture quality.

Note: When sRGB is selected in picture mode, this function cannot be changed.

Gamma correction is handled by the LCD panel.

NATIVE

2.2

2.4

S GAMMA

Typical display gamma for use with a computer.

Good for video (DVD, etc.)

Special gamma for certain types of movies. Raises the dark parts and lowers the light parts of the image (S-Curve).

50

50*

10000K

0

NATIVE*

(except sRGB setting)

DICOM GSDF curve simulated for LCD type.

A programmable gamma curve can be loaded using NEC optional software.

Adjusts the amount of noise reduction. Press + or - to adjust.

50

0*

AUTO* TELECINE

HDMI, DVD/HD, SCART, VIDEO1,

VIDEO2, S-VIDEO inputs only

Automatically senses the sources frame rate for optimal picture quality.

ADAPTIVE CONTRAST

HDMI, DVD/HD, SCART, VIDEO1,

VIDEO2, S-VIDEO inputs only

Sets the level of adjustment for dynamic contrast.

PICTURE MODE

RESET

Selects picture mode, [HIGHBRIGHT], [STANDARD], [sRGB], [CINEMA], [AMBIENT1] or

[AMBIENT2]. See page 20.

Resets the following settings within the PICTURE menu back to factory setting: BACKLIGHT,

CONTRAST, SHARPNESS, BRIGHTNESS, HUE, COLOR, COLOR TEMPERATURE,

COLOR CONTROL, GAMMA CORRECTION, MOVIE SETTINGS.

ADJUST

AUTO SETUP

VGA, RGB/HV inputs only

Automatically adjusts Screen Size, H position, V position, Clock, Phase and White Level.

OFF

Depends on destination

-

-

AUTO ADJUST

VGA, RGB/HV inputs only

H POSITION

All inputs except DVI, HDMI, DPORT

H Position, V Position and Phase are adjusted automatically when new timing is detected.

OFF

-

V POSITION

All inputs except DVI, HDMI, DPORT

CLOCK

VGA, RGB/HV inputs only

Controls the horizontal position of the image within the Display area of the LCD.

Press + to move right. Press - to move left.

Controls the vertical position of the image within the Display area of the LCD.

Press + to move up. Press - to move down.

Press + to expand the width of the image on the right of the screen.

Press - to narrow the width of the image on the left.

Adjusts the visual “noise” on the image.

-

-

-

PHASE

VGA, RGB/HV, DVD/HD, SCART inputs only

*: depends on signal input

English-22

H RESOLUTION

VGA, RGB/HV inputs only

V RESOLUTION

VGA, RGB/HV inputs only

INPUT RESOLUTION

VGA, RGB/HV inputs only

Adjusts the horizontal size of the image.

Adjusts the vertical size of the image.

ASPECT

NORMAL

FULL

WIDE

DYNAMIC

1:1

ZOOM

ZOOM

H ZOOM

V ZOOM

H POS

V POS

RESET

If there is a problem with signal detection, this function forces the monitor to display the signal at the desired resolution. After selection, execute “AUTO SETUP” if required.

If no problem is detected, the only available option will be “AUTO”.

Select the aspect ratio of the screen image.

Displays the aspect ratio the same as it is sent from the source.

Fills entire screen.

Expands a 16:9 letter box signal to fi ll entire screen.

Expands a 4:3 pictures to fi ll the entire screen with non-linearity. Some of the outside image area will be cut off due to expansion. TILE MATRIX becomes invalid.

Display the image in a 1 by 1 pixel format. (If the input resolution is higher than a 1920 x 1080 resolution, the image will be scaled down to fi t the screen). TILE MATRIX becomes invalid.

The image can be expanded/reduced.

Note: The expanded image which is outside of active display area is not shown. The reduced image may have some image degradation.

Maintains the aspect ratio while zooming.

Amount of horizontal zoom.

Amount of vertical zoom.

Horizontal position.

Vertical position.

Resets the following settings within the ADJUST menu back to factory setting: AUTO ADJUST,

H POSITION, V POSITION, CLOCK, PHASE, H RESOLUTION, V RESOLUTION, ASPECT.

AUDIO

VOLUME

BALANCE

TREBLE

BASS

SURROUND

PIP AUDIO

LINE OUT

Increases or decreases output volume level.

Adjust the balance of L/R volume.

Press + button to move the stereo sound image to right.

Press - button to move the stereo sound image to left.

To accentuate or reduce the high frequency sound.

Press + button to increase TREBLE sound.

Press - button to decrease TREBLE sound.

To accentuate or reduce the low frequency sound.

Press + button to increase BASS sound.

Press - button to decrease BASS sound.

Artifi cial surround sound.

Note: Audio out is disabled when this function is set to ON.

Selects source of PIP audio.

Selecting “VARIABLE” enables control of the line out level with the VOLUME button.

Note: Audio out is disabled when this function is set to ON.

INTERNAL SPEAKER

(not adjustable)

AUDIO INPUT Selects audio input source [IN1], [DPORT], [HDMI], [OPTION]*.

AUDIO DELAY Enables to set the delay time to output the audio. DELAY TIME can be set between 0 and 8.

“ON” activates this function.

Resets “AUDIO” options back to factory settings except VOLUME.

RESET

SCHEDULE

OFF TIMER

SCHEDULE SETTINGS

Sets the monitor to power off after a length of time.

A time between 1 to 24 hours is available.

Creates a working schedule for the monitor to use.

NOTE: If your schedule is across date, please set ON time and OFF time individually at Settings.

SCHEDULE LIST List of schedules.

*: The product you purchased may not have this feature.

-

-

-

-

AUTO

FULL

-

-

-

-

40

CENTER

0

0

OFF

MAIN AUDIO

FIXED

Depend on signal input

OFF, 2

-

-

-

-

-

OFF

English-23

DATE & TIME

YEAR

MONTH

DAY

TIME

DAYLIGHT SAVING

RESET

Sets the date, time, and daylight saving region. Date & time must be set in order for the

“SCHEDULE” function to operate. See page 30.

Confi gures the year for the real time clock.

Confi gures the month for the real-time clock.

Confi gures the day for the real-time clock.

Confi gures the time for the real-time clock.

Confi gures daylight savings on or off.

Resets the following settings within the SCHEDULE menu back to factory setting: OFF TIMER and SCHEDULE SETTINGS.

PIP

KEEP PIP MODE

PIP MODE

OFF

PIP

POP

Allows the monitor to remain in “PIP” and “TEXT TICKER” mode after powering off.

When Power is returned, PIP and TEXT TICKER appear without having to enter the OSD.

Selects Picture-in-Picture mode.

Normal mode.

Picture in Picture mode.

Picture out Picture mode.

PICTURE BY PICTURE-

ASPECT

Picture by picture (split screen) mode, with keep aspect.

PICTURE BY PICTURE-

FULL

Picture by picture (split screen) mode, with full screen.

Selects the size of the sub-picture used in Picture-in-Picture (PIP) mode.

PIP SIZE

SMALL

MIDDLE

LARGE

PIP POSITION Determines where the PIP appears on the screen.

Selects sub picture aspect, [FULL], [NORMAL] and [WIDE]. See page 19.

ASPECT

TEXT TICKER

MODE

POSITION

SIZE

Enables Text Ticker and allows you to set Horizontal or Vertical direction.

Selects the location of the Text Ticker on the screen.

Determines the size of the Text Ticker in relationship to the overall screen size.

BLEND

DETECT

FADE IN

SUB INPUT

Sets the transparency of the Text Ticker (0: transparent, 100: opaque).

Enables auto-detection of the Text Ticker.

Enables fade-in of the text ticker.

Selects sub picture input signal.

Resets PIP options back to factory settings except ASPECT and SUB INPUT.

-

-

-

-

OFF

-

OFF

OFF

LARGE

X = 95, Y = 92

FULL

OFF

Depends on signal input

RESET

OSD

LANGUAGE

ENGLISH

DEUTSCH

FRANÇAIS

ITALIANO

ESPAÑOL

SVENSKA

РУССКИЙ

Select the language used by the OSD.

ENGLISH

(Depends on destination)

English-24

MENU DISPLAY TIME

OSD POSITION

UP

OSD TRANSPARENCY

OSD ROTATION

LANDSCAPE

PORTRAIT

INPUT NAME

CLOSED CAPTION

VIDEO1, VIDEO2, S-VIDEO inputs only

Turns off the OSD after a period of inactivity. The preset choices are 10-240 seconds.

Determines the location where the OSD appears on the screen.

DOWN

LEFT

RIGHT

INFORMATION OSD Selects whether the information OSD is displayed or not. The information OSD will be displayed when the input signal or source changes. The information OSD will also give a warning when there is no-signal or the signal is out-of range.

An interval between 3 to 10 seconds for the Information OSD to appear is available.

MONITOR INFORMATION Indicates the model and serial number of your monitor.

CARBON SAVINGS: Display the estimated carbon saving information in kg-CO2. The carbon footprint factor in the carbon saving calculation is based on the OECD (2008 Edition).

CARBON USAGE: Display the estimated carbon usage information in kg-CO2. This is the arithmetic estimation, not actual measurement value. This estimation is based without any options.

Set the transparency of the OSD.

Determines the OSD display direction between landscape and portrait.

Display the OSD with landscape mode.

Display the OSD with portrait mode.

You can create a name for the INPUT currently being used.

Max: 8 characters, including Space, A-Z, 0-9, and some symbols.

Activates closed captioning.

30 Sec.

X = 128, Y = 225

ON, 3 Sec.

ON

LANDSCAPE

-

-

OFF

RESET Resets the following settings within the OSD menu back to factory setting:

MENU DISPLAY TIME, OSD POSITION, INFORMATION OSD, OSD TRANSPARENCY,

CLOSED CAPTION.

MULTI DISPLAY

CONTROL ID

IR CONTROL

NORMAL

PRIMARY

SECONDARY

IR LOCK SETTINGS

Sets the monitor ID number from 1-100 and group ID from A-J. When “YES” is selected in

“AUTO ID”, monitor ID numbers are set automatically in all monitors which follow in the chain with

RS-232C.

NOTE: Group ID is made of multiple selections.

Selects the mode of the monitor for use with the infra-red remote control when using the

RS-232C daisy chain.

The monitor will be controlled normally using the wireless remote control.

Choose “PRIMARY” for the fi rst monitor within an RS-232C daisy chain.

Choose “SECONDARY” for all subsequent monitors within an RS-232C daisy chain.

Prevents the monitor from being controlled by the wireless remote control.

When ACTIVATE is selected, all the settings are activated.

NOTE: IR LOCK SETTINGS is a function intended only to the wireless remote control buttons.

This function does not lock out access to all buttons at the back of the monitor. To return to normal operation, press the “DISPLAY” button on the remote control for 5 seconds.

MODE SELECT

UNLOCK

ALL LOCK

Selects the mode UNLOCK, ALL LOCK or CUSTOM LOCK.

All buttons on the remote control are available for normal operations.

Locks all remote control buttons.

CUSTOM LOCK Selects which buttons to be locked from POWER, VOLUME, and INPUT button.

Except for CUSTOM LOCK settings, other buttons on the remote control are locked.

POWER: When LOCK is selected, POWER button is locked.

VOLUME: When UNLOCK is selected, sets minimum and maximum volume between VOL.0 to

INPUT:

VOL.100.

VOLUME (+) button and VOLUME (-) buttons are only available from the minimum volume to the maximum volume you set.

When LOCK is selected, VOLUME (+) button and VOLUME (-) buttons are locked.

When UNLOCK is selected, choose up to three buttons from DVI, DisplayPort, VGA,

HDMI, DVD/HD* 2 , VIDEO* 2 , S-VIDEO* 2 , OPTION* 1 which you prefer to be unlocked.

The unselected buttons are locked. When LOCK is selected, all INPUT buttons are locked.

*1: This function depends on which option board you use.

*2: This function depends on Terminal setting.

1

NORMAL

UNLOCK

English-25

TILE MATRIX

H MONITORS

V MONITORS

POSITION

TILE COMP

ENABLE

TILE MATRIX MEM

POWER ON DELAY

POWER INDICATOR

EXTERNAL CONTROL

CONTROL

LAN RESET

ID=ALL REPLY

MAC ADDRESS

LAN SETTING

DHCP

IP ADDRESS

SUBNET MASK

DEFAULT GATEWAY

DNS PRIMARY

DNS SECONDARY

SETTING COPY

COPY START

ALL INPUT

RESET

Allows one image to be expanded and displayed over multiple screens (up to 100) through a distribution amplifi er.

NOTE: Low resolution is not suitable for tiling to a large number of monitors. You can operate without a distribution amplifi er at a lower number of screens.

Dynamic or 1:1 will not work when Tile Matrix is activated. When “DYNAMIC” or “1:1 is selected in ASPECT while executing TILE MATRIX, the setting will be applied after TILE MATRIX completion.

Number of monitors arranged horizontally.

Number of monitors arranged vertically.

Select which section of the tiled image to be displayed on the monitor.

Turns the TILE COMP feature on.

Enables Tile Matrix.

When “INPUT” is selected, TILE MATRIX setting is applied to each signal input.

Adjusts the delay time between being in “standby” mode and entering “power on” mode.

“POWER ON DELAY” can be set between 0 and 50 seconds.

Turns ON or OFF the LED located at the front of the monitor.

If “OFF” is selected, LED will not light when the LCD monitor is in active mode.

1

NO

1

1

NO

COMMON

0 Sec.

ON

Selects the control interface, RS-232C or LAN.

Resets the LAN settings.

When controlling the monitor externally, select if the communication command, which specifi es destination equipment ID (ALL or GROUP ID), is replying or not. When you need reply, please select “ON”.

If you connect the multiple monitors that are daisy-chained from second monitor by RS-232C, you need to select “OFF” from second monitor.

Displays the MAC ADDRESS.

When you use this function, EXTERNAL CONTROL should be “LAN”.

NOTE: When changing the LAN SETTING, you need to wait several seconds until the LAN

SETTING is applied.

Enabling this option automatically assigns an IP address to the monitor from your DHCP server.

Disabling this option allows you to register the IP address or subnet mask number obtained from your network administrator.

NOTE: Consult your network administrator for the IP address when “ENABLE” is selected for

[DHCP].

Set your IP address of the network connected to the monitor when “DISABLE” is selected for

[DHCP].

Set your subnet mask number of the network connected to the monitor when “DISABLE” is selected for [DHCP].

Set your default gateway of the network connected to the monitor when “DISABLE” is selected for [DHCP].

Set your primary DNS settings of the network connected to the monitor.

Set your secondary DNS settings of the network connected to the monitor.

In a daisy chain scenario, select the OSD menu categories that you want to copy over to the other monitor.

NOTE: When you use this function, EXTERNAL CONTROL should be “RS-232C”. This function resets to default when power is off. This function has a limit depending on the cable you use.

Select “YES” and press the SET button to start copying.

All input terminals settings are copied when you select this item. Default is off.

Resets “MULTI DISPLAY” options back to factory settings except LAN SETTING and TILE

MATRIX MEM.

RS-232C

-

OFF

0.0.0.0

0.0.0.0

NO

-

-

DISABLE

192.168.0.10

255.255.255.0

192.168.0.1

English-26

DISPLAY PROTECTION

POWER SAVE If AUTO STANDBY is in OFF mode, POWER SAVE must be turned ON for the display to enter the suspend power saving mode when an active signal is not present. The monitor will automatically recover to ON state when a signal is reapplied.

POWER SAVE

AUTO STANDBY

HEAT STATUS

FAN CONTROL

SCREEN SAVER

GAMMA

BACKLIGHT

MOTION

SIDE BORDER COLOR

AUTO BRIGHTNESS

DPORT, DVI, VGA, RGB/HV inputs only

CHANGE SECURITY

PASSWORD

SECURITY

DDC/CI

ALERT MAIL

RESET

Sets how long the monitor waits to go into power save mode after the signal is lost.

Note: When connecting DVI, the display cards might not stop sending the digital data even though the image might have disappeared. If this occurs the monitor will not switch into power management mode.

ON: Monitor automatically goes into OFF mode 10 minutes after signal is lost.

OFF: Monitor does not automatically go into OFF mode even after signal is lost.

NOTE: This function is disabled when RGB, VIDEO or OPTION POWER are enabled.

AUTO STANDBY will not allow the monitor to turn on after a signal is reapplied. The monitor would need to receive a Power ON signal via the remote control, the control buttons RS-232C or

LAN to show an image again.

Displays status of the FAN, BACKLIGHT and TEMPERATURE.

Cooling fan reduces the temperature of the display to protect from overheating.

If “AUTO” is selected, you can adjust the start temperature of the cooling fan and fan speed.

Use the SCREEN SAVER function to reduce the risk of Image Persistence.

The display gamma is changed and fi xed when “ON” is selected.

The brightness of backlight is decreased when “ON” is selected.

NOTE: Do not select this function when picture mode is AMBIENT1 or AMBIENT2.

The screen image is slightly expanded and moves in 4 directions (UP, DOWN, RIGHT, LEFT) at user determined intervals. You can set interval time and zooming ratio.

This function is disabled when PIP, STILL, TEXT TICKER or TILE MATRIX are enabled.

Adjusts the color of the side borders when a 4:3 image is displayed.

Press + button, the bar will become lighter.

Press - button, the bar will become darker.

Adjusts the brightness level according to the input signal.

NOTE: Do not select this function when picture mode is AMBIENT1 or AMBIENT2.

Allows the security password to be changed.

The factory preset password is 0000.

Locks the security password.

START-UP LOCK: Security password is required when the monitor power is on.

CONTROL LOCK: Security password is required when the remote control button or control button on the monitor is pressed.

BOTH LOCK: Security password is required when the monitor power is on, or the remote control button or control button on the monitor is pressed.

ENABLE/DISABLE: Turns ON or OFF the two way communication and control of the monitor.

Selects whether or not to send an e-mail notifi cation of monitor error via wired LAN.

Resets the following settings within the DISPLAY PROTECTION menu back to factory setting: POWER SAVE, FAN CONTROL, SCREEN SAVER, SIDE BORDER COLOR, AUTO

BRIGHTNESS, DDC/CI.

OFF

ON

-

AUTO

OFF

OFF

OFF

15

OFF

-

OFF

ENABLE

OFF

-

English-27

ADVANCED OPTION

INPUT DETECT Selects the method of input detection the monitor uses when more than two input devices are connected.

NONE

FIRST DETECT

The Monitor will not search the other video input ports.

When the current video input signal is not present, then the monitor searches for a video signal from the other video input port. If the video signal is present in the other port, then the monitor switches the video source input port to the new found video source automatically.

The monitor will not look for other video signals while the current video source is present.

LAST DETECT

VIDEO DETECT

CUSTOM DETECT

INPUT CHANGE

When the monitor is displaying a signal from the current source and a new secondary source is supplied to the monitor, the monitor will automatically switch to the new video source. When current video input signal is not present, the monitor searches for a video signal from the other video input port. If the video signal is present in the other port, then the monitor switches the video source input port to the new found video source automatically.

HDMI, DVD/HD, SCART, VIDEO1, VIDEO2 or S-VIDEO inputs will have priority over DVI, VGA,

RGB/HV.

When HDMI, DVD/HD, SCART, VIDEO1, VIDEO2 or S-VIDEO input signal is present the monitor will change and keep to the HDMI, DVD/HD, SCART, VIDEO1, VIDEO2 or S-VIDEO input.

Set the priority of input signals.

When CUSTOM DETECT is selected, monitor searches listed inputs only.

NOTE: OPTION input signal is only available to be set to PRIORITY5.

Sets input change speed.

NOTE: When “QUICK” is selected, picture may be distorted when signal input is changed.

This function should be chosen after all adjustment options have been made for the input.

TERMINAL SETTING

DVI MODE

BNC MODE

HDMI SIGNAL

DEINTERLACE

ON

OFF

COLOR SYSTEM

VIDEO1, VIDEO2, S-VIDEO inputs only

Selects the kind of DVI-D equipment which is connected to the DVI input.

Select “DVI-HD” when DVD player or computer equipment, which requires HDCP authentication, is connected.

Select “DVI-PC” when a computer equipment, which not requires HDCP authentication, is connected.

Selects the type of signal associated with the BNC input.

RGB: Analog input (R, G, B, H, V)

COMPONENT: Component (Y, Cb/Pb, Cr/Pr)

SCART: SCART signal

VIDEO: Composite video (VIDEO2)

S-VIDEO: Separate video

RAW: Disable the expanded feature.

EXPAND: Expand image contrast and increase detail in the dark and bright areas.

Selects the IP (Interlace to Progressive) conversion function.

Note: For DVI input “DVI-HD” needs to be enabled in the DVI mode menu.

Converts interlaced signals to progressive. This is the default setting.

Disables IP conversion. This setting is best suited for motion pictures, but increases the risk of image retention.

The selected Color System depends on the video format of the input signal.

AUTO

NTSC

PAL

SECAM

4.43 NTSC

PAL-60

Automatically chooses Color System setting based on input signal.

NONE

NORMAL

DVI-PC

RGB

EXPAND

ON

AUTO

English-28

OVER SCAN

HDMI, DVD/HD, SCART, VIDEO1, VIDEO2,

S-VIDEO inputs only

ON

Some video formats may require different scanning modes in order to best display the image.

OFF

Image size is larger than what can be displayed. The image edge will appear cropped.

Approximately 95% of the image will be shown on the screen.

Image size stays within the display area. The whole image is displayed on the screen.

NOTE: When you use a computer with HDMI out, please set “OFF”.

OPTION SETTING

OPTION POWER

AUDIO* 1

INTERNAL PC* 1

OFF WARNING

AUTO OFF

START UP PC

FORCE QUIT

Allow the monitor to supply power to Option board slot during power save mode or standby mode.

NOTE: This function should be set to ON when using power save management by slot 2 type option.

Selects sound input signal according to slot2 type option’s specifi cations. To activate DIGITAL, select OPTION(D) for input signal and OPTION for AUDIO INPUT.

NOTE: DIGITAL is activated only when OPTION(D) is selected for input signal and OPTION for

AUDIO INPUT.

The function is available for slot 2 type PC.

If OPTION POWER is OFF, a warning message appears when monitor power is turned off.

Note: Warning message does not appear when monitor power is turned off by OFF TIMER setting or SCHEDULE setting.

Monitor power is automatically “OFF” when connected PC is OFF or the monitor is in power save mode.

NOTE: Monitor power is not automatically “ON” when connected PC is ON.

When ON is selected, connected PC start-up.

When ON is selected, it performs force-quit PC.

Please use this function only when the operating system cannot be shut down manually.

120Hz

(not adjustable)

RESPONSE IMPROVE

(not adjustable)

TOUCH PANEL

STANDBY

PC SOURCE

RESET

NOTE: Touch function does not work in PIP mode. Select the input signal as follows:

Using slot 2 type PC: Select [OPTION].

Using external computer: Select the input signal which is supplied by the PC connected to USB connector.

When ON is selected, touch function is available.

Selects EXTERNAL PC or AUTO (INTERNAL).

Resets the following settings within the ADVANCED OPTION menu back to factory setting:

INPUT DETECT (except the priority of input signals), INPUT CHANGE, TERMINAL SETTING,

DEINTERLACE, COLOR SYSTEM, OVER SCAN, AUDIO in OPTION SETTING, START UP PC in OPTION SETTING and FORCE QUIT in OPTION SETTING.

FACTORY RESET All items are returned to factory shipment state.

NOTE: You can reset all items in all daisy chain displays. Please be careful to avoid resetting all items inadvertently.

*1: This function depends on which option board you use.

ON

OFF

ANALOG

OFF

OFF

NO

NO

-

-

-

ON

-

-

English-29

NOTE 1: CREATING A SCHEDULE

The schedule function allows the display to be set to power on and off at different times. Up to seven different schedules can be programmed.

To program the schedule:

1. Enter the SCHEDULE menu. Highlight SCHEDULE SETTINGS using the up and down buttons. Press the SET or the + button to enter the

Settings menu. Highlight the desired schedule number and press set. The box next to the number will turn yellow. The schedule can now be programmed.

2. Use the down button to highlight the hours setting in the ON time slot. Use the + and - buttons to set the hour. Use the up and down buttons to highlight the minutes setting. Use the + and - buttons to set the minutes. Set the OFF time in the same manner.

3. Use the up and down arrows to highlight INPUT. Use the + and - buttons to choose the input source. Use the up and down arrows to highlight

PIC. MODE. Use the + and - buttons to choose the picture mode.

4. Use the down button to select a day on which the schedule will be enabled. Push the set button to enable. If the schedule is to be ran every day, choose EVERY DAY and press the SET button. The circle next to EVERY DAY will turn yellow. If a weekly schedule is desired, choose the days of the week using the up and down buttons and pressing SET to select. Then highlight the EVERY WEEK option and press SET.

DVI

SCHEDULE:

SCHEDULE SETTINGS

5. After a schedule is programmed the remaining schedules can then be set. Press MENU to leave the OSD or press EXIT to go back to the previous menu.

Note: If schedules are overlapping then the schedule with the highest number will have priority over the schedule with the lowest number. For example schedule #7 will have priority over schedule #1.

If selected input or picture mode is not available now, disable input or picture mode is shown in red.

Choose

SETTINGS:

(THU) JUN.18.2009 15:38

1 2 3 4 5 6 7

ON:

OFF:

INPUT:

PIC. MODE:

– – : – –

– – : – –

– – – –

– – – –

EVERY DAY

EVERY WEEK

MON TUE WED THU

FRI SAT SUN

Mark Return Close

NOTE 2: IMAGE PERSISTENCE

Please be aware that LCD Technology may experience a phenomenon known as Image Persistence. Image Persistence occurs when a residual or “ghost” image of a previous image remains visible on the screen. Unlike CRT monitors, LCD monitors’ image persistence is not permanent, but constant images being displayed for a long period of time should be avoided.

To alleviate image persistence, turn off the monitor for as long as the previous image was displayed. For example, if an image was on the monitor for one hour and a residual image remains, the monitor should be turned off for one hour to erase the image.

As with all personal display devices, NEC DISPLAY SOLUTIONS recommends displaying moving images and using a moving screen saver at regular intervals whenever the screen is idle or turning off the monitor when not in use.

Please set “SCREEN SAVER”, “DATE &TIME” and “SCHEDULE SETTINGS” functions to further reduce the risk of Image persistence.

For long life use as Public Display

Image Sticking of LCD Panel

When an LCD panel is operated continuously for long hours, a trace of electric charge remains near the electrode inside LCD, and residual or

“ghost” image of previous image may be observed. (Image Persistence)

Image Persistence is not permanent, but when fi xed image is displayed for long period, ionic impurities inside LCD are accumulated along the displayed image, and may be permanent. (Image Sticking)

Recommendations

To prevent Image Sticking, and for longer life usage of LCD, the following are recommended.

1. Fixed image should not be displayed for long period. Change fi xed images after short intervals.

2. When not in use, please turn off the monitor by remote control, or use Power Management or use Schedule Functions.

3. Lower environmental temperatures prolong the lifespan of the monitor.

When Protective surface (glass, acrylic) is installed over the LCD surface, the LCD surface is located in an enclosed space, the monitor are stacked, utilize the temperature sensors inside monitor.

To reduce the environmental temperature, use the Cooling Fan, Screen Saver and Low Brightness.

4. Please use “Screen Saver Mode” of monitor.

English-30

advertisement

Related manuals