Chapter 2
Using the Hardware
Using the Keypad
MT380 contains five function keys and twelve numeric keys.
The following table describes the function keys.
Key Main Function
Menu
[F1]: Function Key
Clock-in
[F2]: Function Key
Clock-out
[F3]: Function Key
Break-in
[F4]: Function Key, or [ESC]: Performs the same function as tapping the
button on the touch screen.
Break-out
[F5]: Function Key, or [ENTER]: Enters a carriage return or executes a command.
Using Windows CE Keyboard
The Windows CE Software provides a touch screen keyboard for alphanumeric input. The Windows based keyboard replicates the layout of a standard PC keyboard.
Open the Windows CE keyboard by tapping the “keyboard” icon on the task bar and tapping Keyboard.
Keyboard icon
5
Entering Characters
Character input is the same as on a standard PC keyboard. Tap the on-screen button corresponding to the character you want to input.
International Character Support:
Tap the [áü] button to switch from the Standard English keyboard to the European keyboard or switch from the standard keyboard to perform the desired special characters.
Title bar
Tap to enter special characters
Entering Numerics
Open the Windows CE numeric keyboard by tapping the “keyboard” icon on the task bar and tapping Numeric Keyboard. Tap the on-screen button corresponding to the numeric you want to input.
Title bar
Moving the Keyboard
Tap the title bar and drag the keyboard to the desired location.
Closing the Keyboard
Tap the keyboard icon and tap Hide Input Panel to close Windows CE keyboard.
6
Copyright 2009 Unitech Electronics Co., Ltd. All rights reserved. Unitech is a registered trademark of Unitech Electronics Co., Ltd.
Chapter 2 Using the Hardware
Using the Stylus
CAUTION!
Never use anything other than MT380 stylus on the screen. Using an object other than the stylus could cause permanent damage.
1.
Hold the stylus as you would hold a pencil.
2.
To make a choice from a menu, lightly tap the tip of the stylus on that choice.
3.
Double-tap to open programs.
4.
To write data into a field on a form, use the stylus to print the letters or numbers.
Using Proximity Reader
MT380 features a standard proximity reader, which is compatible with all 125kHz EM, 125kHz HID, and
13.56mHz Mifare cards.
Bring proximity card close here for reading
Testing Proximity Card Verification
MT380 has a built-in demo programs that enable users to make proximity card verification.
1.
Double-tap the My Device icon on the
Windows CE desktop.
7
2.
Double-tap the Flash Storage.
3.
Double-tap MT380 Test AP.
4.
Double-tap the RFID test folder.
5.
Double-tap the PDA_10 to open the demo program.
8
Copyright 2009 Unitech Electronics Co., Ltd. All rights reserved. Unitech is a registered trademark of Unitech Electronics Co., Ltd.
6.
Set the COM Port=2. Tap Connect.
Chapter 2 Using the Hardware
7.
Tap a card type to activate the demo program you want to test.
8.
Tap Auto and bring the proximity card close to the sensor.
The code will be read and displayed on the field below.
9.
Tap Stop to end reading.
9
Using the Finger Print Reader
MT380 has an optional integrated Finger Print reader that able to verify fingerprint in 0.4 seconds per template. The Finger Print Reader can store up to 100 templates.
Place finger here for reading
Testing Finger Print Verification
MT380 has a built-in BIO ID Manager programs that enable users to test finger print verification.
1.
Double-tap the My Device icon on the
Windows CE desktop.
2.
Double-tap the Flash Storage.
10
Copyright 2009 Unitech Electronics Co., Ltd. All rights reserved. Unitech is a registered trademark of Unitech Electronics Co., Ltd.
3.
Double-tap MT380 Test AP folder.
Chapter 2 Using the Hardware
4.
Double-tap the Fingerprint folder to open the demo program.
5.
Double-tap the BioIDMgr to open the demo program.
6.
Tap Open to activate the program.
11
7.
Tap Enroll to input a new sample id for the fingerprint. For example, 123. Tap OK.
8.
Put finger on the sensor three times according to the message shown on screen.
9.
The finger print is enrolled into the program and displayed in the Slot-Id field.
10. Select a finger print id and tap Verify to start verifying the finger print.
A pop-up window appears “Verify live finger with slot 0 id ’123’?”. Tap Yes.
12
Copyright 2009 Unitech Electronics Co., Ltd. All rights reserved. Unitech is a registered trademark of Unitech Electronics Co., Ltd.
11. Put finger on the sensor according to the message shown on screen.
A pop-up window appears with verification results: “Match” or “No match”. Tap OK.
Chapter 2 Using the Hardware
12. Tap Identify to find finger print id info.
Put finger on the sensor according to the message shown on screen.
A pop-up window appears with verification results: “Match found: slot 0 id ‘123’” or
“No match”. Tap OK.
13. Under the Grab/GrabW tab, tap Grab/
GrabWindow to collect a finger print image.
14. Under the Info tab, tap Get Module Info to display the Finger Print module info.
Under the Type drop-down menu, select all, internal, or external, then tap Get
Available Memory to display the Finger
Print Reader’s memory.
13
Using the Camera
MT380 has a built-in 2.0 megapixel camera which provides the following extra functionality:
• Enable users to capture still image when a card is being read
• Verify attendant time with a photo image
• Serve as video recorder
• Function as an audio/video intercom
Additionally, facial recognition can be incorporated using third party software.
MT380 has a demo program that enables users to capture a still picture with a card number and time stamp when a proximity card is read.
Testing the Imager
MT380 has a built-in CameraDemo program that enable users to test the camera efficiency.
1.
Double-tap the My Device icon on the
Windows CE desktop.
2.
Double-tap the Windows folder.
3.
Double-tap CameraDemo to open the demo program.
14
Copyright 2009 Unitech Electronics Co., Ltd. All rights reserved. Unitech is a registered trademark of Unitech Electronics Co., Ltd.
4.
Tap Preview → Start.
A continuous image is displayed enabling users to capture image/audio/vedio.
Chapter 2 Using the Hardware
5.
Tap Capture.
Audio Demo Program
The audio demo program enables you to test audio input (recording) and output (playback).
1.
Double-tap the My Device icon on the
Windows CE desktop.
2.
Double-tap the Windows folder.
15
3.
Double-tap wavtest to open the demo program.
4.
Do one of the following:
– Tap Rec to record the voice
– Tap Stop to finish recording
– Tap Play to listen to the recording
16
Copyright 2009 Unitech Electronics Co., Ltd. All rights reserved. Unitech is a registered trademark of Unitech Electronics Co., Ltd.
