Technical data. Zanussi ZBB29455SA


Add to my manuals
80 Pages

advertisement

Technical data. Zanussi ZBB29455SA | Manualzz

Technical data

Dimension of the recess

Rising Time

Voltage

Frequency

Height

Width

Depth

1780 mm

560 mm

550 mm

24 h

230-240 V

50 Hz

The technical information are situated in the rating plate on the internal left side of the appliance and in the energy label.

Installation

Caution!

Read the "Safety Information" carefully for your safety and correct operation of the appliance before installing the appliance.

Positioning

Install this appliance at a location where the ambient temperature corresponds to the climate class indicated on the rating plate of the appliance:

Climate class

SN

N

ST

T

Ambient temperature

+10°C to + 32°C

+16°C to + 32°C

+16°C to + 38°C

+16°C to + 43°C

Electrical connection

Before plugging in, ensure that the voltage and frequency shown on the rating plate correspond to your domestic power supply.

The appliance must be earthed. The power supply cable plug is provided with a contact for this purpose. If the domestic power supply socket is not earthed, connect the appliance to a separate earth in compliance with current regulations, consulting a qualified electrician.

The manufacturer declines all responsibility if the above safety precautions are not observed.

This appliance complies with the E.E.C. Directives.

Door reversibility

The door of the appliance opens to the right. If you want to open the door to the left, do these steps before you install the appliance:

28 www.zanussi.com

• Loosen the upper pin and remove the spacer.

• Remove the upper pin and the upper door.

• Unscrew the pins

(B) and spacers

(C).

C

B

C

• Remove the lower door.

• Loosen the lower pin.

On the opposite side:

• Install the lower pin.

• Install the lower door.

• Refit the pins (B) and the spacers (C) on the middle hinge on the opposite side.

• Install the upper door.

• Tighten the spacer and tighten the upper pin.

Ventilation requirements

The airflow behind the appliance must be sufficient.

5 cm min. 200cm 2 min.

200cm 2 x

Installing the appliance

Caution!

Make sure that the mains cable can move freely.

Do the following steps: x

A A1

1

If necessary cut the adhesive sealing strip and then apply it to the appliance as shown in figure.

2

Drill the hinge cover A, as shown in figure.

Apply the covers A and A1 (in the accessories bag) in to the middle hinge.

www.zanussi.com

29

2

1

4mm

44mm

3

Install the appliance in the niche.

Push the appliance in the direction of the arrows (1) until the upper gap cover stops against the kitchen furniture.

Push the appliance in the direction of the arrows (2) against the cupboard on the opposite side of the hinge.

4

Adjust the appliance in the niche.

Make sure that the distance between the appliance and the cupboard front-edge is 44 mm.

The lower hinge cover (in the accessories bag) makes sure that the distance between the appliance and the kitchen furniture is correct.

Make sure that the clearance between the appliance and the cupboard is 4 mm.

Open the door. Put the lower hinge cover in position.

E

E

D

C

E

B

7

Attach the covers

(C, D) to the lugs and the hinge holes.

Install the vent grille

(B).

Attach the hinge covers (E) to the hinge.

E

8

If the appliance must connect laterally to the kitchen furniture door:

1.

Slacken the screws in fixing brackets (E).

2.

Move the brackets (E).

3.

Retighten the screws.

Ha Hb

~50 mm

90 o

21 mm

~50 mm

90

21 mm o

Hc Hd

9

Disconnect the parts (Ha), (Hb), (Hc) and (Hd).

10

Install the part

(Ha) on the inner side of the kitchen furniture.

I

I

5

Attach the appliance to the niche with 4 screws.

6

Remove the correct part from the hinge cover (E). Make sure to remove the part DX, in the case of right hinge, SX in opposite case.

30 www.zanussi.com

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals