TROUBLESHOOTING. AEG SKD71800F0


Add to My manuals
64 Pages

advertisement

TROUBLESHOOTING. AEG SKD71800F0 | Manualzz

26 www.aeg.com

The equipment has to be cleaned regularly:

1.

Clean the inside and accessories with lukewarm water and some neutral soap.

2.

Regularly check the door seals and wipe clean to ensure they are clean and free from debris.

3.

Rinse and dry thoroughly.

4.

If accessible, clean the condenser and the compressor at the back of the appliance with a brush.

This operation will improve the performance of the appliance and save electricity consumption.

6.3 Defrosting of the refrigerator

Frost is automatically eliminated from the evaporator of the refrigerator compartment every time the motor compressor stops, during normal use.

The defrost water drains out through a trough into a special container at the back of the appliance, over the motor compressor, where it evaporates.

It is important to periodically clean the defrost water drain hole in the middle of the refrigerator compartment channel to prevent the water overflowing and dripping onto the food inside.

7.

TROUBLESHOOTING

6.4 Periods of non-operation

When the appliance is not in use for long periods, take the following precautions:

1.

Disconnect the appliance from electricity supply.

2.

Remove all food.

3.

Clean the appliance and all accessories.

4.

Leave the door/doors open to prevent unpleasant smells.

WARNING!

If the cabinet will be kept on, ask somebody to check it once in a while to prevent the food inside from spoiling in case of a power failure.

WARNING!

Refer to Safety chapters.

7.1 What to do if...

Problem

The appliance does not operate.

Possible cause Solution

The appliance is switched off.

The mains plug is not connected to the mains socket correctly.

Switch on the appliance.

Connect the mains plug to the mains socket correctly.

There is no voltage in the mains socket.

Connect a different electrical appliance to the mains socket.

Contact a qualified electrician.

ENGLISH 27

Problem

The appliance is noisy.

Possible cause

The appliance is not supported properly.

Solution

Check if the appliance stands stable.

Audible or visual alarm is on. The cabinet has been recently switched on or the temperature is still too high.

Refer to "Door Open Alarm"or

"High Temperature Alarm".

The temperature in the appliance is too high.

Refer to "Door Open Alarm"or

"High Temperature Alarm".

A rectangular symbol is shown instead of numbers on the Temperature Display.

The lamp does not work.

The lamp does not work.

The door is left open.

Close the door.

The temperature in the appliance is too high.

Contact a qualified electrician or contact the nearest Authorized Service Centre.

Temperature sensor problem.

Contact the nearest Authorized Service Centre (the cooling system will continue to keep food products cold, but temperature adjustment will not be possible).

The lamp is in stand-by.

The lamp is defective.

Close and open the door.

Contact the nearest Authorized Service Centre.

Refer to "Operation" chapter.

The compressor operates continually.

Temperature is set incorrectly.

Many food products were put in at the same time.

The room temperature is too high.

Wait some hours and then check the temperature again.

Refer to climate class chart on the rating plate.

The compressor does not start immediately after pressing the COOLMATIC, or after changing the temperature.

Food products placed in the appliance were too warm.

Allow food products to cool to room temperature before storing.

The door is not closed correctly.

Refer to "Closing the door".

The COOLMATIC function is switched on.

This is normal, no error has occurred.

Refer to "COOLMATIC function".

The compressor starts after a period of time.

28 www.aeg.com

Problem Possible cause

Water flows inside the refrigerator.

The water outlet is clogged.

Water flows on the floor.

Food products prevent that water flows into the water collector.

The melting water outlet is not connected to the evaporative tray above the compressor.

Solution

Clean the water outlet.

Make sure that food products do not touch the rear plate.

Attach the melting water outlet to the evaporative tray.

Temperature cannot be set.

DEMO appears on the display.

The temperature in the appliance is too low/too high.

The FROSTMATIC or

COOLMATIC function is switched on.

Switch off FROSTMATIC or

COOLMATIC manually, or wait until the function resets automatically to set the temperature. Refer to "FROSTMATIC or COOLMATIC function".

The appliance is in demonstration mode.

The temperature regulator is not set correctly.

Keep the OK pressed for approximately 10 seconds until a long sound is heard and display shuts off for a short time.

Set a higher/lower temperature.

The door is not closed correctly.

The food products' temperature is too high.

Refer to "Closing the door".

Let the food products temperature decrease to room temperature before storage.

Many food products are stored at the same time.

The door has been opened often.

The COOLMATIC function is switched on.

Store less food products at the same time.

Open the door only if necessary.

Refer to "COOLMATIC function".

There is no cold air circulation in the appliance.

Make sure that there is cold air circulation in the appliance.

If the advice does not lead to the desired result, call the nearest brand-mark service.

7.2 Closing the door

1.

Clean the door gaskets.

2.

If necessary, adjust the door. Refer to

"Installation".

3.

If necessary, replace the defective door gaskets. Contact the After Sales

Service.

advertisement

Related manuals