advertisement
J-200
WARNING:
RISK OF ELECTRICAL SHOCK HAZARD
EXISTS AND EQUIPMENT DAMAGE!
Never install or remove electrical devices (e.g. Apple device/MP3/USB/AUX/
Bluetooth) while hands are wet or while sitting partially or fully immersed in the spa!
CAUTION: Never leave electrical devices in the Media Locker when spa is not is use to prevent damage from outdoor elements! Never spray Media Locker with a pressurized water hose for any reason! Damage to the device or spa stereo system caused by water intrusion is not covered under the manufacturer’s warranty! Damage to Media Locker port or electrical devices due to excessive force or improper alignment during installation or removal from Media Locker is not covered under warranty.
17.1 Pairing the Remote and Stereo
In order for the remote to operate the stereo, you need to pair them using the following method:
1. Make sure the stereo unit is in “Standby” mode.
LED power light will be red, Figure A.
2. Press any button on the remote to turn it ON. The remote
LCD display will read “No Link.”
3. Press and hold the “Mode” button on the remote (Figure B).
At the same time, press and hold the power button on the stereo for 2 seconds (Figure A).
4. The remote LCD display will read “Welcome,” “Load” and
“Radio” if the pairing sequence was successful.
AUDIO
1
DIR -
Figure A
2 3
REPEAT DIR +
MODE
RANDOM
17.2 Audio Settings
The Audio button, Figure C, provides access to many of the stereo’s settings. By continually pressing the Audio button you can scroll and adjust the following functions: BAS-TRE-BAL-
Figure B
AUDIO MODE
FAD-DSP-AREA-LOUD-DX-STEREO (respectively).
Note: You can adjust the settings by pressing the Audio button, making your adjustments and pressing the Audio button to go the next feature. If you exit the setting menus continually press
1
DIR -
2 3
REPEAT DIR + RANDOM
Figure C the Audio button until you reach the setting you would like to adjust.
1. Bass Setting: Press the Audio button once to access the bass setting. The LCD display will change to “BAS
0,” Figure D. Press the Up button to adjust the setting to a Figure D maximum of +5. Press the Down button to adjust the setting down to
-5.
Note: The default setting is “0.” This feature is disabled when a “Digital
Sound Processor” (DSP) setting is active such as “Rock,” “Classic,” or
“Pop.”
53
J-200
2. Treble Setting: Press the Audio button 2 times to access the treble setting. The LCD display will change to “TRE 0,”
Figure E. Press the Up button to adjust the setting to a maximum of +5. Press the Down button to adjust the
Figure E setting down to -5.
Note: The default setting is “0.” This feature is disabled when a “Digital
Sound Processor” (DSP) setting is active such as “Rock,” “Classic,” or
“Pop.”
3. Balance Setting: Press the Audio button 3 times to access the balance setting. The LCD display will change to “BAL L=R,” Figure F. Press the Up button to adjust the
Figure F setting to a maximum of 10R (only the right side speakers will have volume). Press the Down button to adjust the setting down to 10L
(only the left side speakers will have volume).
4. Fade Setting: Press the Audio button 4 times to access the fade setting. The LCD display will change to “FAD
F=R,” Figure G. Press the Up button to adjust the setting to
Figure G a maximum of 10F (only the front speakers will have volume). Press the Down button to adjust the setting down to 10R (only the rear speakers will have volume).
5. Digital Sound Processor (DSP) Setting: Press the
Audio button 5 times to access the DSP setting. The LCD display will change to “DSP OFF,” Figure H. Press the Up button to select one of the preset settings such as Rock,
Classic or Pop. If a preset setting is select a small icon will appear on the LCD display, Figure I.
6. Area Setting: Press the Audio button 6 times to access the Area setting. The LCD display will change to “AREA
USA,” Figure J. Press the Up button to select either USA or
EUR setting.
7. Loud Setting: Press the Audio button 7 times to access the Loud setting. The LCD display will change to “LOUD
OFF,” Figure K. Press the Up button to select either OFF or ON.
Figure H
ROCK
Figure I
Figure J
Figure K
8. Distant Setting: Press the Audio button 8 times to access the Distant setting. The LCD display will change to
“DX,” Figure L. Press the Up button to select either Distant
(DX) or Local for station frequency. The “LOCAL” setting allows for better FM reception when a local station is too strong. Leave the setting to “DX” if this condition does not exist.
Figure L
54
advertisement
