TROUBLESHOOTING. Brinly-Hardy BS26BH

TROUBLESHOOTING

Table 2: Troubleshooting - Spreading Difficulties & Remedies

PROBLEM

Too much/not enough material dispensed.

Flow Control Handle hard to operate or won’t move

Fan does not turn when towing spreader.

CAUSE/CONDTION

Gage Plate not calibrated

REMEDY

Insure Gage Plate is properly calibrated, (Refer to Figure 11).

Gate(47) and directional control plate(46) clogged with material.

Drive hairpin cotter (22) not properly inserted through

Wheel hub (9) hub and axle

(6.)

Transmission cotter pin (40) missing or not properly inserted through transmission hub (21) hub and axle (6)

Fan (25) hits bottom of hopper gate (47) and directional control plate (46).

Fan (25) slips on transmission shaft (21).

Remove and clean the Gate and Directional Control Plate with soap and water, (Refer to Figure 12 through Figure 15).

Install or replace missing hairpin cotter, (Refer to Figure 5)

Install or replace missing cotter pin through transmission hub

(21) hub and axle (6), (Refer to Figure 4).

Adjust fan to clear hopper gate and directional control plate,

(Refer to Figure 6).

Install Fan Driver (24) so that the four fan gussets on the bottom of the fan compresses the fan driver.

Transmission malfunction With the broadcast spreader attached to your machine lift the drive wheel and rotate. At the same time apply gentle pressure to the fan shaft. It should turn with each rotation of the wheel.

SPECIFICATIONS

Dimensions

Size (maximum tow weight) .................................. 79 kg (175 lbs).

Capacity ......................................................... 0.10 cu m (3.5 cu ft).

Tires

Size ...................................................................................... 13 x 5

Inflation Pressure ................................................................. 20 psi

GETTING QUALITY SERVICE

Quality Continues with Quality Service

We provide a process to handle your questions or problems.

Follow the steps below to get answers to any questions you may have about your product.

1. Refer to your attachment and machine operator manuals.

2. In North America or Canada, call 1-877 728-8224 and provide product serial number (if available) and model number.

26.

L-1884-A

L-1884-A

27.

MANUFACTURER’S LIMITED WARRANTY

FOR

Pull Behind Accessories

The limited warranty set forth below is given by Brinly-Hardy

Company with respect to new merchandise purchased and used in the United States, its possessions and territories.

Brinly-Hardy Company warrants the products listed below against defects in material and workmanship, and will at its option, repair or replace, free of charge, any part found to be defective in materials or workmanship. This limited warranty shall only apply if this product has been assembled, operated, and maintained in accordance with the Operator’s manual furnished with the product, and has not been subject to misuse, abuse, commercial use, neglect, accident, improper maintenance, alteration, vandalism, theft, fire, water, or damage because of other peril or natural disaster.

Normal Wear Parts or components thereof are subject to separate terms as follows: All normal wear parts or component failures will be covered on the product for a period of 90 days.

Parts found to be defective within the warranty period will be replaced at our expense. Our obligation under this warranty is expressly limited to the replacement or repair, at our option, of parts found to be defective in material and workmanship.

HOW TO OBTAIN SERVICE:

Warranty parts replacements are available, ONLY WITH PROOF OF PURCHASE, through our

Pull Behind Accessories Customer Service Department. Call

877-728-8224.

This limited warranty does not provide coverage in the following cases: a) Routine maintenance items such as lubricants and filters.

b) Normal deterioration of the exterior finish due to use or exposure.

c) Transportation and/or labor charges.

d) The warranty does not include commercial and/or rental use.

No implied warranty, including any implied warranty of merchantability of fitness for a particular purpose, applies after the applicable period of express written warranty above as to the part as identified below. No other express warranty whether written or oral, except as mentioned above, given by any person or entity, including a dealer or retailer, with respect to any product, shall bind Brinly-Hardy Co. During the period of the warranty, the exclusive remedy is repair or replacement of the product as set forth above.

The provisions as set forth in this warranty provide the sole and exclusive remedy arising from the sale. Brinly-Hardy Co. shall not be liable for incidental or consequential loss or damage including, without limitation, expenses incurred for substitute or replacement lawn care services or for rental expenses to temporarily replace a warranted product.

Some states do not allow the exclusion or limitation of incidental or consequential damages, or limitations on how long an implied warranty lasts, so the above exclusions or limitations may not apply to you.

During the warranty period, the exclusive remedy is replacement of the part. In no event shall recovery of any kind be greater that the amount of the purchase price of the product sold. Alteration of safety features of the product shall void this warranty. You assume the risk and liability for loss, damage, or injury to you and your property and/or to others and their property arising out of the misuse or inability to use this product.

This limited warranty shall not extend to anyone other than the original purchaser or to the person for whom it was purchased as a gift.

HOW STATE LAW RELATES TO THIS WARRANTY:

This limited warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

IMPORTANT:

The Warranty period stated below begins with the

PROOF OF PURCHASE. Without the proof of purchase, the

Warranty period begins from the date of manufacture determined by the serial number manufacturing date.

SPREADER WARRANTY PERIOD:

The warranty period for this spreader is as follows: Steel frame parts, poly hopper, transmission and flow control parts – 2 Years. Tires, wheels and agitator - 90 days.

Brinly-Hardy Company, 3230 Industrial Parkway, Jeffersonville, IN 47130