Electrical Connections. Jacuzzi FUZ7260CCR5CHY, FUZ7242CCR5IWW

Salon™ Spa Bath

Electrical Connections

Risk of electric shock. Connect only to a circuit protected by a GFCI.

When using electrical products, basic precautions should always be followed:

•

Always follow local building and electrical codes.

Grounding is required. The unit should be installed and grounded by a qualified electrician.

Two separate GFCI protected circuits are required.

A separate, 240VAC, 20 Amp GFCI circuit is required for the heater and pump/motor.

A separate, 120VAC, 20 Amp GFCI circuit is required for the blower.

Risk of component overheat. Do not use electric extension cord to power this unit.

Operating the motor/pump without enough water in the bathtub can cause leaking and permanent damage.

At initial startup, the 8 button electronic control system enters an automatic self diagnostic program for 15-20 seconds. During the diagnostic program, the system will not accept user commands.

Blower , Pump and Motor

1

For the blower, install a 120 VAC, 15AMP, GFCI duplex outlet to the stud wall underneath the bathtub at 4˝ (101mm) above the floor. The duplex outlet is not supplied.

The duplex outlet must be mounted 4˝ (101mm) above the floor line, or in accordance with local building and electrical codes.

2

3

For the pump/motor and heater, install a 240

VAC, 20 AMP RATED GFCI outlet to the wall stud underneath the bathtub, at least 4˝ (101mm) above the floor. The outlet is not provided.

Power cords from the heater and the pump/motor are routed to a fused junction box at the factory. A supplied power cord from the junction box with a

240 VAC plug connects to the customer supplied

GFCI dedicated circuit.

4 With a #8 solid copper wire, ground the heater to the house electrical panel or approved local bond. A grounding lug is provided on the heater.

5 At initial start-up, and before each use thereafter with power ON, push the GFCI test button. The reset button should pop out.

3-Prong Plug

4˝

(101mm) Floor

120V Duplex Receptacle

(not supplied)

240V GFCI Protected Circuit

TM

4˝

(101mm)

Power Cord from Control

Box to GFCI Circuit

Heater

Push the GFCI test button in to reset. If the interrupter fails to operate in this manner, there is a ground current flowing or a device malfunction, indicating the possibility of electrical shock.

Turn OFF power and do not use the bathtub until the source of the problem has been identified and corrected.

Installation and Operation www.jacuzzi.com

Page 11

Salon™ Spa Bath

Reference Illustrations

These illustrations are for reference only, as the unit comes fully assembled.

Risk of electric shock. Before servicing these connections, disconnect all power supply cables to both 120VAC service and 240VAC service.

J4 Control Panel Schematic Diagram

Air Valve Assembly

240VAC

20A

GFCI

Motor/Pump

120VAC

15A

GFCI

SEE VIEW A

Control Panel

Illumatherapy

Lights

Control Box

Junction Box

Chromatherapy

Lights

Air Valve 240VAC Pump

Panel Blower LED Lights

Blower

Heater

J5 Control Panel Schematic Diagram

Air Valve Assembly

240VAC

20A

GFCI

Junction Box

Control Panel

Motor/Pump

SEE VIEW A

Illumatherapy

Lights

Temperature

Sensor

Control Box

Air Valve

RS232

Panel Blower

Inside

Light 1

Inside

Light 2

Inside

Light 3

Inside

Light 4

Ambient

Light 1

Ambient

Light 2

Temp

Sensor

LOGO

Light

240VAC Pump

Chromatherapy

Lights

120VAC

15A

GFCI

View A

Lead Connectors

4 - Green (GRD)

3 - Red (L)

2 - Black (H)

1 - White (C)

Page 12

Heater www.jacuzzi.com

Blower

Lead Connectors

4 - Green (GRD)

3 - Red (L)

2 - Black (H)

View A

Installation and Operation