Removing and installing components. Dell Vostro 15 5568 77 Pages Pagine ページ
advertisement annuncio pubblicitario 広告
Ask Al about Removing and installing components. Dell Vostro 15 5568
Chatbot has read manual and is ready to answer your questions.
3
Removing and installing components
This section provides detailed information on how to remove or install the components from your computer.
Recommended tools
The procedures in this document require the following tools:
• Phillips #0 screwdriver
• Phillips #1 screwdriver
• Small plastic scribe
Removing the back cover
1
Follow the procedures in Before working inside your computer
.
2 Remove the screws that secure the back cover to the computer.
Figure 5. Removing screws
3 To remove the cover: a Using a scribe, pry the edges of the back cover from all sides [1].
12 Removing and installing components
b Lift the back cover from the computer [2].
Figure 6. Prying at the edge to remove the back cover
Installing the back cover
1 Align the back cover with the screw holes on the computer.
2 Tighten the screws to secure the base cover to the computer.
3
Follow the procedure in After working inside your computer
Removing the battery module
1
Follow the procedure in Before working inside your computer
.
2
.
3 To remove the battery: a Disconnect the battery cable from the connector on the system board [1].
b Remove the screws that secure the battery to the computer [2].
c Lift and remove the battery from the computer [3].
Removing and installing components 13
Figure 7. Removing the battery
Installing the battery
1 Insert the battery into the slot on the computer.
2 Install the screws that secure the battery to the computer.
3 Connect the battery cable to the connector on the system board.
4 Install the
5
Follow the procedure in After working inside your computer
Removing the battery cable
1
Follow the procedure in Before working inside your computer
.
2 Remove the: a
b
3 Disconnect the battery cable from its connector on the battery.
14 Removing and installing components
Installing the battery cable
1 Connect the battery cable to the battery cable on the battery.
2 Install the: a
b
3
Follow the procedure in After working inside your computer
Removing the solid state drive - SSD bracket
1
Follow the procedure in Before working inside your computer
.
2 Remove the: a
b
3 To remove the SSD : a Remove the screws that secure the SSD [1] .
b Lift to remove the SSD from the computer [2].
Removing and installing components 15
Installing the solid state drive - SSD
1 Insert the SSD into its slot on the computer.
2 Tighten the screws that secure the SSD .
3 Install the: a
b
4
Follow the procedure in After working inside your computer
Removing the hard drive
1
Follow the procedure in Before working inside your computer
.
2 Remove the: a
b
3 To remove the hard drive: a Lift the tab to disconnect the hard drive cable from the connector on the system board [1] .
b Remove the screws that secure the hard drive to the computer [2].
c Lift the hard drive from the computer [3].
16 Removing and installing components
Installing the hard drive
1 Insert the hard drive assembly into its slot on the computer.
2 Tighten the screws that secure the hard drive to the computer
3 Connect the hard drive cable to the connector on the system board.
4 Install the: a
b
5
Follow the procedure in After working inside your computer
Removing the hard drive bracket
1
Follow the procedure in Before working inside your computer
.
2 Remove the: a
b
c
d
3 To remove the hard drive bracket: a Remove the screws that secure the hard drive bracket to the hard drive [1].
b Lift and remove the hard drive bracket [2].
Removing and installing components 17
Installing the hard drive bracket
1 Place the hard drive bracket to align with the hard drive.
2 Install the screws that secure the hard drive bracket.
3 Install the: a
b
c
d
4
Follow the procedure in After working inside your computer
Removing the hard drive cable
1
Follow the procedure in Before working inside your computer
.
2 Remove the: a
b
c
3 Disconnect the hard drive cable from the connector on the hard drive.
18 Removing and installing components
Installing the hard drive cable
1 Connect the hard drive cable to the hard drive.
2 Install the: a
b
c
3
Follow the procedure in After working inside your computer
Removing the memory module
1
Follow the procedure in Before working inside your computer
.
2 Remove the: a
b
3 To remove the memory module: a Pull the retention clips from the memory module until it pops up. [1] b Remove the memory module from the connector on the system board. [2]
Removing and installing components 19
Installing the memory module
1 Insert the memory module into the memory module socket.
2 Press the memory module until it clicks into place.
3 Install the: a
b
4
Follow the procedure in After working inside your computer
Removing the WLAN card
1
Follow the procedures in Before working inside your computer
.
2 Remove the: a
b
3 To remove the WLAN card: a Remove the screw that secures the WLAN card to the computer and lift the plastic tab [1] [2].
b Disconnect the antenna cables from the WLAN card [3].
c Remove the WLAN card from the slot on the system board [4].
20 Removing and installing components
Installing the WLAN card
1 Insert the WLAN card into the connector at a 45–degree angle.
2 Close the plastic cover over the WLAN card.
3 Tighten the screw to secure the WLAN card to the computer.
4 Connect the antenna cables to the connectors marked on the WLAN card.
5 Install the: a
b
6
Follow the procedure in After working inside your computer
Removing the touchpad
1
Follow the procedure in Before working inside your computer
.
2 Remove the: a
b
c
3 To release the touchpad: a Peel away the adhesive tape [1].
b Disconnect the connector cables from the system board as indicated [2] [3] [4. ]
Removing and installing components 21
4 To remove the metal bracket above the touchpad: a Remove the screws that secure the metal bracket to the touchpad. [1] b Lift the metal bracket away from the touchpad. [2]
22 Removing and installing components
5 To remove the touchpad: a Remove the screws that secure the touchpad to the computer [1].
b Lift and remove the touchpad away from the computer [2].
Removing and installing components 23
Installing the touch pad
1 Align the touch pad assembly on the computer chassis.
2 Install the screws that secure the touch pad assembly.
3 Place the metal bracket over the touch pad assembly.
4 Install the screws that secure the metal bracket to the touch pad assembly.
5 Connect the touch pad cables to the connectors on the computer.
6 Affix the adhesive tape over the touch pad assembly.
7 Install the: a
b
c
8
Follow the procedure in After working inside your computer
Removing the coin cell battery
1
Follow the procedure in Before working inside your computer
.
2 Remove the: a
b
3 To remove the coin cell battery: a Pry the coin cell battery upwards from its slot using a scribe [1] .
b Lift and remove the coin cell battery [2].
24 Removing and installing components
Installing the coin cell battery
1 Insert the coin cell battery into the slot on the computer.
2 Install the : a
b
3
Follow the procedure in After working inside your computer
Removing the Input-Output board
1
Follow the procedure in Before working inside your computer
.
2 Remove the: a
b
c
3 To remove the I/O board: a Disconnect the I/O board connector cable from the system board [1] [2] [3].
b Remove the screw that secures the I/O board to the system board [4].
c Lift and remove the I/O board from the computer [5].
Removing and installing components 25
Installing the Input-Output board
1 Insert the I/O board into the slot on the computer chassis.
2 Install the screw that secures the I/O board to the computer.
3 Connect the I/O board cables to the system board.
4 Install the: a
b
c
5
Follow the procedure in After working inside your computer
Removing the fan
1
Follow the procedure in Before working inside your computer
.
2 Remove the: a
b
c
3 To remove the fan: a Disconnect the I/O board and system board cables from the connectors on the system board [1] [2].
b Unroute the WLAN connector cables from the fan module [3].
26 Removing and installing components
4 To remove the fan: a Disconnect the fan connector cable from the system board [1].
b Remove the screws that secure the system fan to the system board [2].
c Lift and remove the system fan from the computer [3].
Removing and installing components 27
Installing the fan
1 Install the fan into the slot on the system board.
2 Tighten the screws to secure the fan module.
3 Connect the I/O board and system fan cable to the system board connectors.
4 Install the: a
b
c
5
Follow the procedure in After working inside your computer
Removing the heatsink
1
Follow the procedure in Before working inside your computer
.
2 Remove the: a
b
c
3 To remove the heatsink: a Remove the screws that secure the heatsink module to the computer chassis.
28 Removing and installing components
NOTE: Loosen the screws in the order of the callout numbers [1, 2, 3, 4, 5, 6, 7]. Except for screws [5,6,7] the rest of the screws are retention screws and cannot be fully removed b Remove the heatsink module from the slot on the system board [8].
Installing the heatsink
1 Place the heatsink module into its slot on the system board.
2 Tighten the screws to secure the heatsink module to the computer.
NOTE: Secure the screws in the order of the callout numbers [1, 2, 3, 4] as seen on the heatsink module. Tighten the rest of the screws.
3 Install the: a
b
c
4
Follow the procedure in After working inside your computer
Removing the LED board
1
Follow the procedure in Before working inside your computer
.
2 Remove the: a
b
3 To remove the LED board: a Lift the tab to disconnect the LED board connector cables from the system board [1].
b Remove the screw that secures LED board to the computer chassis [2].
c Remove the LED board from the computer [3].
Removing and installing components 29
Installing the LED board
1 Place the LED module into its slot on the computer chassis.
2 Tighten the screw to secure the LED module to the computer chassis.
3 Connect the LED module cables to the computer chassis.
4 Install the: a
b
5
Follow the procedure in After working inside your computer
Removing the speakers
1
Follow the procedure in Before working inside your computer
.
2 Remove the: a
b
3 To remove the speaker cables: a Disconnect the speaker connector cables from the system board and the LED board. [1] [2].
b Unroute the speaker cable from around the LED board [3].
30 Removing and installing components
4 To remove the speakers: a Unroute the cables along the routing channels.
b Lift and remove the speakers from the computer.
Removing and installing components 31
Installing the speakers
1 Insert the speakers into the slot on the computer chassis.
2 Route the speaker cable along the routing channel.
3 Connect the speaker cables to the connectors on the system board and the LED board.
4 Install the: a
b
5
Follow the procedure in After working inside your computer
Removing the system board
1
Follow the procedure in Before working inside your computer
.
2 Remove the: a
b
c
d
e
f
g
h
i
3 Lift the tab [1,2,3,4,6] to disconnect the cables [5] from their connectors on the system board.
32 Removing and installing components
4 To remove the system board cables: a Disconnect the display power supply cable [1].
b Lift the tab to disconnect the display connector cable [2].
Removing and installing components 33
5 To remove the system board: a Remove the screws that secure the system board to the computer chassis [1].
b Lift to remove the system board away from the computer [2].
34 Removing and installing components
Installing the system board
1 Align the system board into its slot on the computer chassis.
2 Install the screws that secure the system board to the computer.
3 Connect the power supply and display cables to their connectors.
4 Connect the following cables: a Display power supply cable b Display connector cable
5 Install the: a
b
c
d
e
f
g
h
i
6
Follow the procedure in After working inside your computer
Removing the display assembly
1
Follow the procedure in Before working inside your computer
.
Removing and installing components 35
NOTE: If you have purchased the touch version of this computer, you will not be able to further disassemble the display.
Instead the entire display assembly needs to be replaced.
2 Remove the: a
b
c
3 To remove the display hinges: a Lift the tab to disconnect the display cables from the system board [1] .
b Lift the display cable latch [2] .
c Unroute the display cable from around the system fan [3] [4].
d Peel away the tape that attaches the display cable to the computer. [5]
4 Flip the computer base around to access the display panel.
36 Removing and installing components
5 To remove the display panel: a Place the computer on a flat surface as indicated.
b Remove the screws that secure the display hinges to the computer chassis. [1] c Lift to remove the display panel. [2]
Removing and installing components 37
Installing the display assembly
1 Align the display assembly with the display hinges of the computer chassis.
2 Tighten the screws that secure the display hinges.
3 Connect the display cables to the connector on the system board.
4 Affix the tape to attach the display cable to the computer.
5 Route the display cables along the system fan module on the chassis.
6 Install the: a
b
c
7
Follow the procedure in After working inside your computer
Removing the display bezel
1
Follow the procedure in Before working inside your computer
.
2 Remove the: a
b
c
d
e
38 Removing and installing components
f
3 To remove the display bezel: a Lift the corners of the bezel with a plastic scribe to remove it .
Installing the display bezel
1 Place the display bezel on the display panel and press along the edges until it clicks in place.
2 Install the: a
b
c
d
e
f
3
Follow the procedure in After working inside your computer
Removing the display panel hinges
1
Follow the procedure in Before working inside your computer
.
2 Remove the: a
b
c
d
e
f
g
3 To remove the display panel hinges:
Removing and installing components 39
a Remove the screws that secure the display panel hinges [1].
b Lift and remove the display panel hinges from the computer [2].
Installing the display panel hinges
1 Install the display panel hinges on the display assembly.
2 Install the screws that secure the display panel hinges.
3 Install the: a
b
c
d
e
f
g
4
Follow the procedure in After working inside your computer
Removing the camera
1
Follow the procedure in Before working inside your computer
.
2 Remove the : a
b
c
d
e
f
40 Removing and installing components
g
3 To remove the camera: a Disconnect the camera connector cable. [1] b Lift to remove the camera from the computer. [2]
Installing the camera
1 Align the camera to its slot on the display panel.
2 Connect the camera cable to its connector on the display panel.
3 Install the: a
b
c
d
e
f
g
4
Follow the procedure in After working inside your computer
Removing the display
1
Follow the procedure in Before working inside your computer
.
2 Remove the: a
b
c
d
e
Removing and installing components 41
f
g
h
3 To remove the display : a Remove the screws that secure the display [1].
b Lift the display panel and turn it over [2].
4 To remove the display: a Peel away the adhesive tape above the display connector [1].
b Disconnect the display connector and remove the display from the display panel [2] [3].
42 Removing and installing components
Installing the display
1 Connect the display connector cable to its connector on the display panel.
2 Affix the adhesive tape over the connector.
3 Flip the display around and align it along the edges of the display panel.
4 Install the screws that secure the display to the display panel.
5 Install the: a
b
c
d
e
f
g
h
6
Follow the procedure in After working inside your computer
Removing the palmrest
1
Follow the procedure in Before working inside your computer
.
2 Remove the: a
b
c
d
e
f
Removing and installing components 43
g
h
i
j
3 The palmrest can be removed after all other components have been disassembled.
Installing the palmrest
1 Align the palmrest into its slot on the computer chassis.
2 Install the: a
b
c
d
e
f
g
h
i
j
3
Follow the procedure in After working inside your computer
Removing the power connector
1
Follow the procedure in Before working inside your computer
.
2 Remove the: a
b
c
44 Removing and installing components
d
e
f
g
h
i
j
3 To remove the power connector: a Lift the power connector cable from its routing channel. [1] b Lift to remove the power connector from the computer. [2]
Installing the power connector
1 Align the power connector into its slot on the computer chassis.
2 Install the: a
b
c
d
e
f
g
h
i
j
3
Follow the procedure in After working inside your computer
Removing and installing components 45
advertisement
Related manuals
advertisement
Table of contents
- 3 Vostro 15-5568 Owner's Manual
- 7 Working on your computer
- 7 Safety instructions
- 7 Before working inside your computer
- 8 Turning off your computer
- 8 After working inside your computer
- 9 Product overview
- 12 Removing and installing components
- 12 Recommended tools
- 12 Removing the back cover
- 13 Installing the back cover
- 13 Removing the battery module
- 14 Installing the battery
- 14 Removing the battery cable
- 15 Installing the battery cable
- 15 Removing the solid state drive - SSD bracket
- 16 Installing the solid state drive - SSD
- 16 Removing the hard drive
- 17 Installing the hard drive
- 17 Removing the hard drive bracket
- 18 Installing the hard drive bracket
- 18 Removing the hard drive cable
- 19 Installing the hard drive cable
- 19 Removing the memory module
- 20 Installing the memory module
- 20 Removing the WLAN card
- 21 Installing the WLAN card
- 21 Removing the touchpad
- 24 Installing the touch pad
- 24 Removing the coin cell battery
- 25 Installing the coin cell battery
- 25 Removing the Input-Output board
- 26 Installing the Input-Output board
- 26 Removing the fan
- 28 Installing the fan
- 28 Removing the heatsink
- 29 Installing the heatsink
- 29 Removing the LED board
- 30 Installing the LED board
- 30 Removing the speakers
- 32 Installing the speakers
- 32 Removing the system board
- 35 Installing the system board
- 35 Removing the display assembly
- 38 Installing the display assembly
- 38 Removing the display bezel
- 39 Installing the display bezel
- 39 Removing the display panel hinges
- 40 Installing the display panel hinges
- 40 Removing the camera
- 41 Installing the camera
- 41 Removing the display
- 43 Installing the display
- 43 Removing the palmrest
- 44 Installing the palmrest
- 44 Removing the power connector
- 45 Installing the power connector
- 46 Technology and components
- 46 Power adapter
- 46 Processors
- 46 Identifying the processor in Windows 10 and Windows 8
- 46 Verifying the processor usage in Task Manager
- 47 Verifying the processor usage in Resource Monitor
- 47 Chipsets
- 48 Downloading the chipset driver
- 48 Identifying the chipset in Device Manager on Windows 10 and Windows 8
- 48 Graphic options
- 49 Downloading drivers
- 49 Identifying the display adapter
- 49 Changing the screen resolution
- 49 Rotating the display
- 50 Display options
- 50 Adjusting brightness in Windows 10
- 50 Adjusting brightness in Windows 8
- 50 Cleaning the display
- 50 Connecting to external display devices
- 51 Audio controller
- 51 Downloading the audio driver
- 51 Identifying the audio controller in Windows 10
- 51 Changing the audio settings
- 52 WLAN cards
- 52 Secure Boot screen options
- 52 Hard drive options
- 52 Identifying the hard drive in Windows 10 and Windows 8
- 53 Identifying the hard drive in the BIOS
- 53 Camera features
- 53 Identifying the camera in Device Manager on Windows 10
- 53 Identifying the camera in Device Manager on Windows 8
- 53 Starting the camera
- 54 Starting the camera application
- 55 Memory features
- 55 Intel chipset drivers
- 55 Intel HD Graphics drivers
- 56 Realtek HD audio drivers
- 57 System Setup
- 57 System Setup overview
- 57 Boot Sequence
- 57 Navigation keys
- 58 Updating the BIOS in Windows
- 58 System Setup options
- 61 Technical Specifications
- 61 Physical Dimensions
- 61 System information specifications
- 61 Processor specifications
- 61 Memory specifications
- 62 Audio specifications
- 62 Video specifications
- 62 Communication specifications
- 62 Battery specifications
- 63 Ports and connector specifications
- 63 Display specifications
- 64 Touchpad specifications
- 64 Keyboard specifications
- 64 Adapter specifications
- 64 Environmental specifications
- 66 System setup options
- 66 General screen options
- 67 System Configuration screen options
- 68 Video screen options
- 68 Security screen options
- 70 Secure Boot screen options
- 70 Performance screen options
- 71 Power Management screen options
- 72 POST Behavior screen options
- 73 Virtualization support screen options
- 73 Wireless screen options
- 74 Maintenance screen options
- 74 System Log screen options
- 75 Troubleshooting
- 75 Enhanced Pre-Boot System Assessment — ePSA diagnostics
- 75 LED error codes
- 76 Battery status lights
- 77 Contacting Dell
- 77 Contacting Dell