Advertisement
Advertisement
Section 4 BASIC OPERATION
Basic Copying Procedure
1
Warm-up
3
Selecting Functions
Turn ON (|) the Power Switch. The [Start] key will light up after warm up has been completed.
2
Setting the Original
Set the copy original on the glass platen. Align the original so that the left rear corner is flush against the original size indicator.
Note
Please refer to P.7-2 "Setting Originals in the
Document Processor" for the procedure used for
placing the original when using the optional Document
Processor.
Select any of the various functions available.
• Making enlarged and reduced copies (Refer to P.4-4.)
• Interrupt Copying (Refer to P.4-6.)
• Making 2-Sided copies from various types of originals (Refer to
*
• Page Separation/Split Copy Modes (Refer to P.5-4.)
• Making a margin space on the copies (Refer to P.5-6.)
• Making copies with clean edge (Refer to P.5-8.)
• Fitting the image of either two or four originals onto
a single copy page (Refer to P.5-10.)
• Automatic Sorting of copy sets (Refer to P.5-15.)
* The Duplex Unit (option) is necessary.
4
Paper Selection
Inch specifications Metric specifications
When Automatic Paper Selection is lit, a paper size identical to the original will be automatically selected. Press the [Paper Select] key in order to select a different paper size to copy.
Notes
• It is possible to turn off the Automatic Size Selection
function. (Refer to P.6-19 "Drawer Selection" .)
• It is also possible to select the drawer that is to be
automatically given priority for use. (Refer to P.6-20
.)
4-1
Section 4 BASIC OPERATION
5
Image Quality Selection
The Image Quality can be selected to match the type of original to be copied. Press the Image Quality Selection key to light up the
Image Quality Mode to be used.
Text & Photo Mode : Use this when the original contains a mixture of text and photos.
Photo Mode : Use this when copying a photograph taken with a camera.
Text Mode : Use this when copying originals that contain a large amount of text.
Notes
• The Image Quality Mode selected in the Default
Setting Mode can be changed. (Refer to P.6-12
• The density of each of the Image Quality Modes can be
adjusted. (Refer to P.6-15 "Text & Photo Mode
Adjustment" and P.6-16 "Text Adjustment
• When horizontal lines stand out in Photo Mode, select
Dithering (Refer to P.6-18 "Photo Processing" ). Note,
however, that the images will be rougher when
Dithering is used.
6
Adjusting Copy Exposure
Pressing the [Auto Exposure] key will detect the copy exposure and set it to the optimal setting.
Notes
• The exposure can be adjusted when the overall exposure is too light or too dark using Auto Exposure.
(Refer to P.6-14 "Auto Exposure Adjustment"
.)
• The Copy Exposure Adjustment can be set to Auto
Exposure Mode when setting the Default Settings.
(Refer to P.6-13 "Exposure Mode" .)
• Pressing the Exposure Adjustment key will move the scale in increments of 0.5 and allow even finer
adjustment of the exposure. (Refer to P.6-14
• When the Photo Mode has been selected using Image
Quality Selection, Auto Exposure cannot be selected.
7
Setting the Number of Copies
Press the numerical keypad to input and display the desired number of copies. Up to 250 copies can be set at a single time.
Note
The maximum number of copies that can be made at one
time can also be restricted. (Refer to P.6-24 "Copy
8
Start Copying
The Copy Exposure (density) is adjusted manually. To make the copy darker, press the Exposure Adjustment key on the right and move the exposure scale to the right. To make the copy lighter, press the Exposure Adjustment key on the left and move the exposure scale to the left.
Press the [Start] key When the Start indicator lights green copying can be begun.
4-2
9
Completion of the Copying Procedure
The finished copy will be ejected into the copy store section.
IMPORTANT!
Up to 250 regular paper copies (80 g/m 2 ) can be stored.
Note, however, that the number of copies that can be stored may differ with the condition of the paper used.
Section 4 BASIC OPERATION
CAUTION
When the copier will not be used for a period of time, such as at night, turn off the power switch.
When it will not be used for longer periods of time such as during long holiday periods, remove the plug from the outlet in the interest of safety.
4-3
Section 4 BASIC OPERATION
Making enlarged and reduced copies
Automatic Magnification Selection
Mode
Reduction/Enlargement is done to match the selected Paper Size
(Drawer).
11" × 17": 129%
(A3: 141%)
8
1/2
" × 11"
(A4)
3
Press the [Paper Select] key and select the paper.
The magnification for the copy will be displayed in accordance with the paper size.
Inch specifications Metric specifications
5
1/2
" × 8
1/2
": 64%
(A5: 70%)
IMPORTANT!
When this is to be used as the default Mode, set the
to on.
1
Set the original.
The original’s size will be automatically detected.
4
Press the [Start] key to begin copying.
Zoom Mode
The magnification can be changed within the range from 50 to
200% in 1 percent increments
50%
2
Press the Zoom Selection key to light up the Automatic
Magnification Selection display.
Inch specifications Metric specifications
200%
IMPORTANT!
When the magnification is changed in the Auto Paper
Select Mode, the magnification for the selected paper size is also changed to match the magnification.
1
Set the original.
2
Press the Zoom (+), Zoom (–) or [Recall%/Enter] key.
The copy magnification will be displayed in the No. of
Copies display and “%” will light up.
Inch specifications Metric specifications
4-4
3
Change the zoom percentage displayed using the Zoom (+) or Zoom (–) key.
The percentage can also be input using the Keypad.
Inch specifications Metric specifications
Section 4 BASIC OPERATION
4
Press the [Enter] key. After the zoom percentage has been confirmed the display changes back to the No. of Copies display.
Inch specifications Metric specifications
5
Press the [Start] key to begin copying.
4-5
Section 4 BASIC OPERATION
Interrupt Copying
Interrupt Copying is useful when you want to make a copy of a different original at different settings during copying operations.
After the Interrupt Copy has been produced, the copying operation resumes at the same settings in effect prior to the interruption.
4
After the Interrupt copy has been produced, pressing the
[Interrupt] key will cause the display to light up. Replace it with the original that had been put aside and press the
[Start] key to resume copying. Press the [Start] key to resume copying.
1
Press the [Interrupt] key. The Interrupt indicator will blink. It will stay lit when the Interrupt operation becomes possible.
2
Temporarily storing the original during copy operations.
3
Set the original for the Interrupt operation and copy it.
4-6
Low Power Mode
Pressing the [Energy Saver] key will put the copier into a resting state even when the Power Switch is ON. The No. of Copies display on the Operation Panel will change to “- - -”, the Conserve Power indicator will light up and all other indicators will be turned off.
Press any key on the Operation Panel or open and close the
Original Cover in order to resume copying operations. In the case where the optional Document Processor is installed, placing an original in the Document Processor will also revert the copier to the state where copies can be made. The recovery time before copies can be made is within 10 seconds.
Section 4 BASIC OPERATION
Note
A function to automatically enter the Low Power Mode after a set interval in which no copies have been
produced has passed is also included. (Refer to P.6-14
4-7
Section 4 BASIC OPERATION
Auto Off Mode
The Auto Off Function is a function that automatically turns the copier off after a set period of time (1 to 240 minutes) has passed.
“-” is displayed in the No. of Copies display and all other indicators are unlit.
This has been set to 30 minutes at shipping.
Inch specifications Metric specifications
Notes
• In the Off Mode state, the supply of electrical power to everything except the operating section is stopped.
When the Power Switch is turned off, the supply of power to everything, including the operating section, is stopped.
• The No. of Copies display will show a “-” for approximately 5 seconds after the Power Switch has been turned off.
Press the [Energy Saver] key in order to resume copying operations. The recovery time before copies can be made is within
19.8 seconds.
Auto Off Mode
The Auto Off Function is a power-saving function that automatically puts the copier into Off Mode when no copying operations have been performed for a set period of time.
In the case of copiers, the amount of time spent idling rather than copying is large, so the amount of power consumed during idle operation makes up the largest share of their power usage. The consumption of power during idling or when someone forgets to turn the copier off after work can be reduced through the copier unit automatically entering the Off Mode and the electric bill reduced as a result.
Notes
• The time interval before the Auto Off Mode engages
can be changed. (Refer to P.6-31 "Off Mode
• The Auto Off Mode can be deselected. (Refer to P.6-29
4-8

Public link updated
The public link to your chat has been updated.
Advertisement