Basic connections. Pioneer lx01bd

Add to My manuals
116 Pages

advertisement

Basic connections. Pioneer lx01bd | Manualzz

LX01BD_1.book Page 12 Tuesday, September 2, 2008 12:33 PM

02

Basic connections

Receiver subwoofer

Display unit

OUT IN 3

HDMI

IN 2 IN 1

SYSTEM

F.AUDIO

iPod

DISPLAY UNIT

MCACC

SETUP MIC

INPUT

SYSTEM

Rear panel

1

SYSTEM

Display cable

2

AM loop antenna

3

FRONT-L

FM antenna

ANTENNA

AM LOOP

Side panel

L

R

ANALOG

AUDIO IN

R

FRONT

R

CENTER

L L

FRONT

R L

SURROUND SUB

4

CENTER-L

Front/center speaker (L)

Front/center speaker (R)

Important

• When connecting this system or changing connections, be sure to switch power off and disconnect the power cord from the wall socket.

After completing all connections, connect the power cords to the wall socket.

WARNING

• Pioneer bears no responsibility for accidents resulting from faulty assembly or installation, insufficient mounting strength of walls, mounting fixtures (or other building fixtures), misuse or natural disasters.

12

En

Downloaded from www.Manualslib.com

manuals search engine

Surround speaker (L)

SURROUND-L

Listening position

Surround speaker (R)

SURROUND-R

LX01BD_1.book Page 13 Tuesday, September 2, 2008 12:33 PM

1 Connect the display unit to the receiver subwoofer.

Plug the display cable into the connector on the rear of the display unit, then plug the other end of the display cable into SYSTEM connector on the receiver subwoofer.

4 Connect each speaker.

• Each speaker cable has a color-coded connector at one end and two wires at the other end.

Color-coded wire

(Connect to speaker)

02

Caution

• Do not attempt to attach the display unit to the wall.

2 Assemble the AM loop antenna.

a b c

Color-coded connector

(Connect to receiver subwoofer)

• Twist and pull off the protective shields on each wire.

a. Bend the stand in the direction indicated by the arrow.

b. Clip the loop onto the stand.

c. If you want to fix to a wall or other surface, perform step b after first securing the stand with screws.

It is recommended that you determine the reception strength before securing the stand with the screws.

3 Connect the AM and FM antennas.

a. Connect one wire of the AM loop antenna to each AM antenna terminal.

For each terminal, press down on the tab to open; insert the wire, then release to secure.

2

3

1

• Connect the wires to the speaker. Each speaker in the illustration can be identified by means of the color-coded indicator provided on the rear-surface model label. Match the color-coded wire with the color indicator on the model label, then insert the color-coded wire into the red ( + ) side and the other wire into the black ( – ) side.

Black ( – ) Red ( + )

Color-coded wire

• Connect the other end to the color-coded speaker terminals on the side of the receiver subwoofer. Make sure to insert completely.

Be careful when inserting the speaker plug, as it must be inserted in the proper direction when being plugged into one of the terminals. Please make sure to connect correctly.

b. Push the FM antenna plug onto the center pin of the FM antenna socket.

Note

• Keep antenna cables away from other cables, the display unit, receiver subwoofer and Blu-ray disc player.

• If reception with the supplied antenna is poor, see Improving poor FM reception and Improving poor AM sound on page 34 or

Connecting external antennas on page 42.

• Do not attach any antenna other than the provided loop antenna, or an external antenna as described on page 44.

• Don’t let it come into contact with metal objects and avoid placing near computers, television sets or other electrical appliances.

• If radio reception is poor, you may be able improve it by reinserting each antenna wire into the opposite terminal.

• For best reception, do not untwist the AM loop antenna wires or wrap them around the loop antenna.

• To ensure optimum reception, make sure the FM antenna is fully extended and not coiled or hanging at the rear of the unit.

Caution

• These speaker terminals carry HAZARDOUS LIVE voltage . To prevent the risk of electric shock when connecting or disconnecting the speaker cables, disconnect the power cord before touching any uninsulated parts.

• Do not connect any speakers other than those supplied to this system.

• Do not connect the supplied speakers to any amplifier other than the one supplied with this system. Connection to any other amplifier may result in malfunction or fire.

• After connecting the plugs, pull lightly on the cables to make sure that the ends of the cables are securely connected to the terminals. Poor connections can create noise and interruptions in the sound.

• If the cables’ wires happen to be pushed out of the terminals, allowing the wires to come into contact with each other, it places an excessive additional load on the amp. This may cause the amp to stop functioning, and may even damage the amp.

13

En

Downloaded from www.Manualslib.com

manuals search engine

LX01BD_1.book Page 14 Tuesday, September 2, 2008 12:33 PM

02

R

AUDIO OUT ( 2 ch )

L

L

FRONT SURROUND SURROUND BACK CENTER

R

AUDIO OUT ( 7.1 ch ) SUB WOOFER

CONTROL

IN

OPTICAL

DIGITAL

OUT

HDMI OUT

Y

P

B

VIDEO OUT

VIDEO

P

R

COMPONENT

VIDEO

S-VIDEO

5

Receiver subwoofer

Side panel Rear panel

OUT IN 3

HDMI

IN 2 IN 1

OUT 1 OUT 2

CONTROL

IN 1 IN 2

OPTICAL

DIGITAL

SYSTEM

6

To HDMI input

7

From digital audio output (optical)

AC IN

Blu-ray disc player

5 Connect the Blu-ray disc player to the receiver subwoofer.

a. Plug the control cable into the CONTROL OUT 1 jack on the side of the receiver subwoofer.

Plug the other end of the cable into the CONTROL IN jack on the rear of the Blu-ray disc player.

b. Plug the HDMI cable into the HDMI IN 1 jack on the rear of the receiver subwoofer.

Plug the other end of the cable into the HDMI OUT jack on the rear of the Blu-ray disc player.

TV

-

7 Connect an audio cable from your TV to the receiver subwoofer.

• To listen to TV audio on this unit, connect the TV’s audio output to DIGITAL OPTICAL IN 1 on the receiver subwoofer.

To use the HDMI Control function when you are connected to a supported Pioneer Flat Screen TV, you must connect via HDMI.

• You must first set ‘ TV Input ’ to switch the audio from a Flat

Screen TV with the HDMI Control function or to switch the input source of this unit to TV audio and operate your TV with the supplied remote control. For more information, see Operating

Pioneer Flat Screen TV and TVs on page 21 and Audio input settings from TVs (TV Input) on page 40.

Note that unless the control cable is connected, you can’t use the remote control with the Blu-ray disc player.

14

En

6 Connect the receiver subwoofer to your TV.

• Connect the HDMI OUT jack on receiver subwoofer to an HDMI input on your TV.

• You can have audio from the receiver subwoofer, as well as audio and video from the Blu-ray disc player, output to your TV by connecting with a single HDMI cable.

Downloaded from www.Manualslib.com

manuals search engine

LX01BD_1.book Page 15 Tuesday, September 2, 2008 12:33 PM

Note

• When digital connections are used, it may be necessary to adjust the digital audio output settings on the TV. For details, consult the operating instructions for your TV.

• About the different types of Blu-ray disc players:

– Use the AUDIO OUT (2 ch) and AUDIO OUT (7.1 ch) terminals to connect a separately sold receiver and listen to 2-channel or

7.1-channel sound, respectively.

– Use the VIDEO OUT terminals to connect to a TV not equipped with an HDMI terminal.

8 Connect the power cord.

• Connect each power cord to the AC inlet on the Blu-ray disc player and the receiver subwoofer. Connect each power cord to a wall socket in the following order:

1. Blu-ray disc player

2. Receiver subwoofer

3. TV

AC IN

Blu-ray disc player

To AC outlet

Receiver subwoofer

To AC outlet

• Run the cords that are connected to the side panel of the receiver subwoofer over the back side of the unit, and replace the cover on the side panel.

Note

• Do not use any power cord other than the one supplied with this system.

• Do not use the supplied power cord for any purpose other than connecting to this system.

• After connecting this unit to an AC outlet, a 15-second initialization process begins. You cannot carry out any operations during initialization. The HDMI indicator on the display unit blinks during initialization, and you can turn this unit on once it has stopped blinking.

Downloaded from www.Manualslib.com

manuals search engine

02

15

En

advertisement

Related manuals

advertisement

Table of contents