Report Event. Symmetricom TimeSource 500

Add to My manuals
306 Pages

advertisement

Report Event. Symmetricom TimeSource 500 | Manualzz

S S S S S S S S S S S S S S S S S S S S S S S S S S S S S

Report Event

This autonomous message appears when an event is raised, and again when the event is cleared; also appears when a transient event occurs. An event is a state of the TimeSource 3500 that does not cause an alarm.

Message:

^^^<sid> <date> <time>

M^^<atag> REPT EVT EQPT <modifier>

^^^"<aid>:<condtype>,<condeff>,<ocrdat>,<ocrtm>

,,,,:\"<conddescr>\"[:<dgntype>]"

Note: Refer to Table I for parameter definitions.

2

TimeSource 3500

TL1 Reference

097-72050-01 Issue 7: August 2003

173

5

S S S S S S S S S S S S S S S S S S S S S S S S S S S

Tasks/Commands

S

To perform each task, use the command listed beside that task in

Table J.

S

4

Table J. Commands for Tasks

Task

Log user onto system

Log user off of system

Copy software program or database

Delete equipment from the database

Delete a user from system

Change communication port parameters

Change the system date and time

Change equipment parameters

Enter equipment into the database and allow the equipment to be used for monitoring

Enter a new user and configure the new user’s user name, password, and access level

Reset the alarm log

Reset to zero all performance monitoring parameters associated with a given aid

Command

Activate User

Cancel User

Copy Memory

Delete Equipment

Delete User Security

Edit Communication

Edit Date

Edit Equipment

Enter Equipment

Enter User Security

Initialize Log

Initialize Register

Page

177

178

179

182

183

184

188

191

201

203

204

205

174

TimeSource 3500

TL1 Reference

097-72050-01 Issue 7: August 2003

S S S S S S S S S S S S S S S S S S S S S S S S S S S S S

Table J. Commands for Tasks (cont’d)

Reset the system processor or GPS receiver processor

Deactivate the audible office alarm

Display current system alarms

Display current alarms for specific equipment

Display current communication port parameter settings

Display current system alarms and events

Display current alarms and events for specific equipment

Display parameter settings of equipment

Display GPS status information

Display header information

Display information about equipment

Display alarm log data

Task

Display performance monitoring data

Command

Initialize System

Operate Alarm Cutoff All

Retrieve Alarm All

Retrieve Alarm Equipment

Retrieve Communication

Retrieve Condition All

Retrieve Condition Equipment

Retrieve Equipment

Retrieve GPS Status

Retrieve Header

Retrieve Inventory

Retrieve Log

Retrieve Performance

Monitoring

Retrieve User Security Display security parameters for a single user or for all users

Set the name of the equipment Set Source Identifier

Page

206

207

208

209

211

214

215

217

227

229

230

233

234

250

251

2

5

TimeSource 3500

TL1 Reference

097-72050-01 Issue 7: August 2003

175

4

176

S S S S S S S S S S S S S S S S S S S S S S S S S S S

Commands

S

The commands used with the TimeSource 3500 are listed on the following pages. After the command name, a definition of the command is given. The definition is followed by the actual command, followed by the variables that can be used with the command.

S

The response format shows how the response will appear, with additional definitions of the response parameters where required.

TimeSource 3500

TL1 Reference

097-72050-01 Issue 7: August 2003

S S S S S S S S S S S S S S S S S S S S S S S S S S S S S

Activate User

This command logs the user onto the system, and begins a session. The factory-set user name is “TELECOM”, and the factory-set password is “TS3000!!”. The user name and password are not case sensitive (either uppercase or lowercase can be used).

The command format is:

ACT-USER:[<tid>]:<uid>:<ctag>::<pid>;

2

Parameter

<uid>

<pid>

Parameter Description

Assigned user name

Assigned password

Command Example:

ACT-USER::TELECOM:<ctag>::TS3000!!;

Response Format:

<sid> <date> <time>

M <ctag> COMPLD

/*LINK:<link>,CMD:<command>*/

;

5

TimeSource 3500

TL1 Reference

097-72050-01 Issue 7: August 2003

177

4

S S S S S S S S S S S S S S S S S S S S S S S S S S S S

Cancel User

This command logs the current user off the system, and logs other users off the system as well, provided the current user has access rights of 5. The user name is not case sensitive, but must otherwise be entered exactly as assigned.

S

To cancel another user, type the command with the UID as the user name to be logged out.

The command format is:

CANC-USER:[<tid>]:<uid>:<ctag>;

Parameter

<uid>

Parameter Description

Assigned user name

Command Example:

CANC-USER::TELECOM:<ctag>;

Response Format:

<sid> <date> <time>

M <ctag> COMPLD

/*LINK:<link>,CMD:<command>*/

;

178

TimeSource 3500

TL1 Reference

097-72050-01 Issue 7: August 2003

S S S S S S S S S S S S S S S S S S S S S S S S S S S S S

Copy Memory

This command copies a software program from an external computer to the TimeSource 3500, or copies the system database to nonvolatile memory.

Notes:

1. The Software Release Document (included with this software release) contains detailed instructions for copying programs from an external computer to nonvolatile memory.

2. Clear any existing alarms before using this command.

3. The database is automatically copied to nonvolatile memory once per hour. However, if power to the TimeSource 3500 is interrupted before the automatic copying occurs, changes made since the last automatic copy will be lost. To avoid the possibility of losing database changes, the Copy Memory command may be used to copy database changes to nonvolatile memory after any changes are made.

To copy a program from an external computer to nonvolatile memory within the TimeSource 3500, the command format is:

2

CPY-MEM:[<tid>]:<aid>:<ctag>::AUX,,WKG:PGM;

TimeSource 3500

TL1 Reference

097-72050-01 Issue 7: August 2003

179

5

4

S S S S S S S S S S S S S S

Copy Memory (cont’d)

S S S S S S S S S S S S S S S

Aid

TS3000

GPS

DEV1

DEV3

DEV5

DEV9

DEV11

Item Addressed

System software

GPS receiver software

TimeSource 3500 (standard)

(990-72050-01 systems) or

TimeSource 3500 with two T1 outputs and eight composite clock outputs (990-72050-03 systems)

TimeSource 3500 with two TOD IRIG-B outputs

(990-72050-05 systems)

TimeSource 3500 with eight additional T1 outputs

(990-72050-02 systems)

TimeSource 3500 with eight mixed E1/T1 outputs

(990-72050-06 systems)

TimeSource 3500 with eight mixed T1/CCK outputs

(990-72050-07)

Command Example:

CPY-MEM::TS3000:<ctag>::AUX,,WKG:PGM;

Response Format:

^^^<sid> <date> <time>

M^^<atag> REPT EVT <modifier>

^^^"<aid>:<condtype>,<condeff>,<ocrdat>,<ocrtm>

,,,,:\"<conddescr>\"[:<dgntype>]"

180

TimeSource 3500

TL1 Reference

097-72050-01 Issue 7: August 2003

S S S S S S S S S S S S S S S S S S S S S S

Copy Memory (cont’d)

Note:

Refer to Table I for parameter definitions.

S S S S S S S

To copy a database from volatile to nonvolatile memory within the

TimeSource 3500, the command format is:

CPY-MEM:[<tid>]:<aid>:<ctag>::WKG,,AUX:DATA;

2

TS3500

Aid

System Database

Item Addressed

Command Example:

CPY-MEM::TS3500:<ctag>::WKG,,AUX:DATA;

Response Format:

<sid> <date> <time>

M <ctag> COMPLD

/*LINK:<link>,CMD:<command>*/

;

TimeSource 3500

TL1 Reference

097-72050-01 Issue 7: August 2003

181

5

4

S S S S S S S S S S S S S S S S S S S S S S S S S S S S

Delete Equipment

This command deletes the specified equipment from the database, removes the input from the ensembling algorithm, and stops the monitoring for that input. Alarms are not reported for deleted equipment. The command format is:

S

DLT-EQPT:[<tid>]:<aid>:<ctag>::<spec_block>

SPAN-a

Aid Value a = A a = B

Item Addressed

T1 span A input

T1 span B input

Command Example:

DLT-EQPT::SPAN-A:<ctag>;

Response Format:

<sid> <date> <time>

M <ctag> COMPLD

/*LINK:<link>,CMD:<command>*/

;

182

TimeSource 3500

TL1 Reference

097-72050-01 Issue 7: August 2003

S S S S S S S S S S S S S S S S S S S S S S S S S S S S S

Delete User Security

This command allows a system administrator to delete a user. The command format is:

DLT-USER-SECU:[<tid>]:<uid>:<ctag>;

Parameter

<uid>

Parameter Description

Assigned user name

Command Example:

DLT-USER-SECU::TELECOM:<ctag>;

Response Format:

<sid> <date> <time>

M <ctag> COMPLD

/*LINK:<link>,CMD:<command>*/

;

2

TimeSource 3500

TL1 Reference

097-72050-01 Issue 7: August 2003

183

5

S S S S S S S S S S S S S S S S S S S S S S S S S S S S

Edit Communication

This command changes communication port parameters. The command format is:

S

ED-COM:[<tid>]:<aid>:<ctag>:::<spec_block>;

4

184

Aid Value

COM-a a = 1 a = 2

Item Addressed

Serial communication port 1 (COM1)

Serial communication port 2 (COM2) a = 3 Serial communication port 3 (Craft) a = 5001 Ethernet user interface port 5001 (Note 1) a = 5002 Ethernet user interface port 5002 (Note 1) a = 5003 Ethernet user interface port 5003 (Note 1) a = 5004 Ethernet user interface port 5004 (Note 1) a = 5551 Ethernet element manager interface port 5551

(Note 2)

Notes:

1. Ethernet ports 5001, 5002, 5003, and 5004 are set up to act as serial communication ports, so that a terminal program on a computer connected to these ports can communicate effectively.

2. Ethernet port 5551 is set up to allow an element manager to connect with it for TL1 commands and responses. TL1 autonomous messages are sent through port 5550, which connects to an element manager to send one or a group of autonomous messages, then disconnects. Port 5550 is not to be reconfigured.

TimeSource 3500

TL1 Reference

097-72050-01 Issue 7: August 2003

S S S S S S S S S S S S S S S S S S S S S S S S S S S S S

Edit Communication (cont’d)

The parameters which can be entered in the <spec_block> are listed below. For any specific <aid> entered in a command, only certain parameters are valid. For each valid parameter, choose the appropriate value from the Value column. When entering multiple parameters, separate the parameters with commas .

Aid Parameter Value Description

COM-a MONMSG=b

KEEPALIVE=b b = ALW b = INH b = 1 to

255

View messages from all ports

View messages from this port only

Inactive minutes until the unit sends a COMPLD message to keep the connection from being closed b = 0 No COMPLD message is output

ENDOFTEXT=b b = 1 to 9F Hex code at end of all responses

ECHO=b

COMPRI=b b = 0 b = ALW

No hex code at end of responses

Echoes characters received so they appear on the user’s screen as typed

Local echo is disabled b = INH b = ALW0 TL1 commands and responses, no autonomous messages sent b = ALW1 TL1 commands and responses, autonomous messages b = ALW2 TL1 commands and responses, autonomous messages whether logged on or not b = INH Closes connection, logs off any user (if logged on), and keeps port from use.

Releases a telnet session from an Ethernet port (a port cannot close itself)

TimeSource 3500

TL1 Reference

097-72050-01 Issue 7: August 2003

185

2

5

4

S S S S S S S S S S S S S S S S S

Edit Communication (cont’d)

S S S S S S S S S S S S

Aid

COM-a

(cont’d)

Parameter Value Description

AUTOLOGOFF=b b = 1 to 255 Inactive minutes until the unit logs off the user, keeping the connection open b = 0 Autologoff is disabled

HWCONTROL=b

(See Note 4) b = ALW

SWCONTROL=b

(See Note 4) b = INH b = ALW b = INH

Serial port CTS/RTS flow control is enabled

Serial port CTS/RTS flow control is not enabled

XON/XOFF flow control is enabled

XON/XOFF flow control is not enabled

BAUD=b

(See Note 3)

PARITY=b

(See Note 3) b = 115 b = 57.6

b = 38.4

b = 19.2

b = 9600 b = 4800 b = 2400 b = 1200 b = EVEN

Serial port baud rate is 115 kbaud

Serial port baud rate is 57.6 kbaud

Serial port baud rate is 38.4 kbaud

Serial port baud rate is 19.2 kbaud

Serial port baud rate is 9600 baud

Serial port baud rate is 4800 baud

Serial port baud rate is 2400 baud

Serial port baud rate is 1200 baud

Even parity is enabled on serial port

STOP=b

(See Note 3) b = ODD Odd parity is enabled on serial port b = NONE No parity is enabled on serial port b = 1 b = 2

1 stop bit on serial port

2 stop bits on serial port

186

TimeSource 3500

TL1 Reference

097-72050-01 Issue 7: August 2003

S S S S S S S S S S S S S S S S S S S S S S S S S S S S S

Edit Communication (cont’d)

Notes:

3. Baud rate, parity, and stop bits can only be configured on serial communication ports (1, 2, and 3).

4. Flow control is not implemented on communication port 3

(Craft port).

5. XON/XOFF flow control is simulated for Ethernet ports.

2

Command Example:

ED-COM::COM-1:<ctag>:::BAUD=9600,MONMSG=ALW,

KEEPALIVE=30,ENDOFTEXT=0,ECHO=ALW,

COMPRI=ALW1,AUTOLOGOFF=30,HWCONTROL=ALW,

SWCONTROL=ALW,PARITY=NONE,STOP=1;

Response Format:

<sid> <date> <time>

M <ctag> COMPLD

/*LINK:<link>,CMD:<command>*/

;

TimeSource 3500

TL1 Reference

097-72050-01 Issue 7: August 2003

187

5

4

S S S S S S S S S S S S S S S S S S S S S S S S S S S S

Edit Date

This command changes the system date and time. The command format is:

S

ED-DAT:[<tid>]::<ctag>::<date>,[<time>]

:[MODE=a];

Parameter date in the format a-b-c time in the format a-b-c (Note 1)

MODE=a

Value Parameter Description a = <year> 4-digit year b = 01 to 12 Month c = 01 to 31 Day a = 00 to 23 Hour of the day b = 00 to 59 Minutes c = 00 to 59 Seconds a = UTC

(Note 2)

Uses Universal Coordinated Time from

GPS (cannot set time by TL1 command) a = LOCAL Uses local time for hours, UTC for minutes and seconds

Notes:

1. The <time> value can only be entered when MODE=LOCAL, or in the same command as MODE=LOCAL, otherwise the command is denied. A successful command with <time> changes the display of time to conform to the nearest 30 minutes, relative to UTC.

188

TimeSource 3500

TL1 Reference

097-72050-01 Issue 7: August 2003

S S S S S S S S S S S S S S S S S S S S S S S S S S S S S

Edit Date (cont’d)

For example, when the UTC time is 01:12:10, setting the local time to 18:50:30 will actually set the clock to 18:42:10, because

18:42:10 is the closest 30 minute jump, relative to UTC, from

18:50:30. This is done to accommodate 30-minute time zones and still keep the local time accurate to UTC.

2. If a command includes MODE=UTC, and the GPS signal is not present, the command is denied.

The date/time behavior is as follows:

• During warm-up:

The date/time displayed starts from 1970 and increments from there. If the ED-DAT command is used to set the time in local mode, the time is changed as specified in the command.

• After warm-up:

If the ED-DAT command has not been used to set the local mode time, then UTC date and time are displayed.

If the ED-DAT command has been used to set the local mode time, then it is changed in the manner described as follows.

The date given in the ED-DAT command is retained.

The local hours, minutes, and seconds are set to the nearest 30-minute divisible difference from UTC. A few examples will help to clarify.

> Example 1. UTC time = 01:00:00. Local time =

18:01:10 will set the local time to 18:00:00.

> Example 2. UTC time = 01:00:00. Local time =

18:25:30 will set the local time to 18:30:00.

2

5

TimeSource 3500

TL1 Reference

097-72050-01 Issue 7: August 2003

189

4

S S S S S S S S S S S S S S S S S S S S S S S S S S

Edit Date (cont’d)

> Example 3. UTC time = 01:12:10. Local time =

18:50:30 will set the local time to 18:42:10.

• During Holdover Event

S S S

The date/time continues to increment normally.

• During Holdover Alarm

The date/time continues to increment normally.

Example to set date without changing time or mode:

ED-DAT:::<ctag>::2000-08-13;

Example to change to local time:

ED-DAT:::<ctag>::2000-08-13,07-00-00:MODE=LOCAL;

Example to change from local to UTC time:

ED-DAT:::<ctag>::2000-08-13:MODE=UTC;

Response Format:

<sid> <date> <time>

M <ctag> COMPLD

/*LINK:<link>,CMD:<command>*/

;

190

TimeSource 3500

TL1 Reference

097-72050-01 Issue 7: August 2003

S S S S S S S S S S S S S S S S S S S S S S S S S S S S S

Edit Equipment

This command changes equipment parameters. Additionally, this command can cause an input to be ensembled. The command format is:

ED-EQPT:[<tid>]:<aid>:<ctag>:::<spec_block>;

TS3500

Aid

GPS

SPAN-a

T1-a

OPT-a

Value

— a = A

— a = B a = A a = B a = 1 to 8

Item Addressed

System-wide configuration

GPS configuration

T1 span A input

T1 span B input

T1 A output

T1 B output

T1 output module port number

(990-72050-02, 990-72050-06, and 990-72050-07 systems only)

2

TimeSource 3500

TL1 Reference

097-72050-01 Issue 7: August 2003

191

5

S S S S S S S S S S S S S S S S S S S S S S S S S S S S

Edit Equipment (cont’d)

The parameters which can be entered in the <spec_block> are listed below. For any specific <aid> entered in a command, only certain parameters are valid. For each valid parameter, choose the appropriate value from the Value column. When entering multiple parameters, separate the parameters with commas .

S

4

Aid Parameter

TS3500 TOD=a

ALMCOND =a

IPNE=a.b.c.d

(See Note 1)

IPSUBNET=a.b.c.d

(See Note 1)

Value Description a = CISCO Serial message sent in Cisco format a = NTP4 Serial message sent in NTP Type 4 format a = NONE No serial message sent a = ALW a = INH

Alarm conditioning for T1, TOD, and IRIG-B outputs is enabled

Alarm conditioning for T1, TOD, and IRIG-B outputs is disabled a = 0 to 255 IP address of this TimeSource 3500 b = 0 to 255

(command must be sent from COM1, c = 0 to 255

COM2, or Craft port to set this parameter) d = 0 to 255 a = 0 to 255 Subnet mask for this TimeSource 3500 b = 0 to 255 c = 0 to 255

(command must be sent from COM1,

COM2, or Craft port to set this parameter) d = 0 to 255

192

TimeSource 3500

TL1 Reference

097-72050-01 Issue 7: August 2003

S S S S S S S S S S S S S S S

Edit Equipment (cont’d)

S S S S S S S S S S S S S S

Aid

TS3500

(cont’d)

SPAN

A & B

TS3500,

SPAN

A & B

Parameter

ALARM=x

ALARM=x

TIME=x

SEVERITY1=x

(See Note 7)

SEVERITY2=x

(See Note 7)

SERAFF1=x

(See Note 7)

SERAFF2=x

(See Note 7) x = CR x = MJ x = MN x = EV x = NA x = SA x = NSA x = SA x = NSA

Value Description x = HOLDOVER HOLDOVER alarm x = GPS x = LOS x = AIS

GPS alarm

LOS alarm

AIS alarm x = ERROR x = HH-MM

ERROR alarm

Hour (00-999) and minute (00-59) time to escalate alarm

No alarm escalation

Severity of initial alarm prior to escalation x = 0 x = CR x = MJ x = MN x = EV x = NA

Severity of escalated alarm

Service affecting state of initial alarm prior to escalation

Service affecting state of escalated alarm

2

5

TimeSource 3500

TL1 Reference

097-72050-01 Issue 7: August 2003

193

S S S S S S S S S S S S S S

Edit Equipment (cont’d)

S S S S S S S S S S S S S S S

4

Aid

TS3500

(cont’d)

Parameter

IPGATE=a.b.c.d

(See Note 1)

IPEM1=a.b.c.d

(See Notes 1, 2,

3)

Value Description a = 0 to 255 Default gateway IP address for this b = 0 to 255

TimeSource 3500 (command must be sent from COM1, COM2, or Craft c = 0 to 255 port to set this parameter) d = 0 to 255 a = 0 to 255 IP address of primary element b = 0 to 255 manager (port 5550 connects to this element manager to send autonomous c = 0 to 255 messages, disconnects when transmit d = 0 to 255 is complete) a = 0 to

65535

Port address of primary element manager (port for IPEM1 address)

IPEM1PORT=a

(See Notes 1, 2,

3)

IPEM2=a.b.c.d

(See Notes 1, 2,

3)

IPEM2PORT=a

(See Notes 1, 2,

3)

IPINACT=a

(See Note 1) a = 0 to 255 IP address of alternate element b = 0 to 255 manager (if used) (port 5550 connects to this element manager if connection c = 0 to 255 d = 0 to 255 cannot be made to the primary element manager) a = 0 to

65535

Port address of alternate element manager (port for IPEM2 address) a = 0 to

10000

Port 5550 closes the connection to the

Element Manager if no autonomous messages are sent during this number of 100-ms units (0 to 10,000, where

0 deactivates the timer, for example,

100 = 10 s)

194

TimeSource 3500

TL1 Reference

097-72050-01 Issue 7: August 2003

S S S S S S S S S S S S S S S

Edit Equipment (cont’d)

S S S S S S S S S S S S S S

GPS

Aid Parameter

ANTCBLDLY=a

(See Note 4)

ANTELEVMASK=a

(See Note 4)

ANTMODE=a

Value Description a = 0 to 300 Antenna cable length (meters) a = 0 to 45 Antenna elevation mask angle

(degrees) a = AUTO Automatic survey-in mode (use only with roof antenna configuration) a =

MANUAL

MANLAT=a-b-c-d a = N

Manual survey-in mode (do not use with roof antenna configuration)

North latitude

MANLONG= a-b-c-d a = S South latitude b = 0 to 180 Degrees of latitude c = 1 to 59 Minutes of latitude d = 1 to 999 Decimal minutes of latitude a = E a = W

East longitude

West longitude b = 1 to 180 Degrees of longitude c = 1 to 59 Minutes of longitude

MANELEVALT=a d = 1 to 999 Decimal minutes of longitude a = –1000 to 8000

Antenna elevation (meters)

TS3500 NTPPWD=x

(See Note 5) x = 6 ASCII characters

NTP Password

(contact factory)

2

5

TimeSource 3500

TL1 Reference

097-72050-01 Issue 7: August 2003

195

S S S S S S S S S S S S S S

Edit Equipment (cont’d)

S S S S S S S S S S S S S S S

Aid

SPAN-a

(See Note 7)

T1-a

Parameter Value

ENSEMBLER=b b = ALW

SSM=b

(See Note 6) b = INH b = ALW

ALMOUT=b b = INH b = AIS b =

SQUELCH b = SSM

FRAMING=b

4

OPT-a

(Additional

T1 ports on

990-72050-

02 systems only)

ALMOUT=b

FRAMING=b b = ESF b = D4 b = AIS b =

SQUELCH b = SSM b = ESF b = D4

Description

Span is ensembled

Span is not ensembled

SSM qualifies span input

SSM does not qualify span input

Output is AIS during holdover alarm

No output during holdover alarm

Outputs are at ‘STU’ quality level during holdover alarm (SSM requires

ESF output framing)

Output framing is ESF

Output framing is D4

Output is AIS during holdover alarm

No output during holdover alarm

Outputs are at ‘STU’ quality level during holdover alarm (SSM requires

ESF output framing)

Output framing is ESF

Output framing is D4

196

TimeSource 3500

TL1 Reference

097-72050-01 Issue 7: August 2003

S S S S S S S S S S S S S S S

Edit Equipment (cont’d)

S S S S S S S S S S S S S S

Aid

OPT-a

(990-

72050-06 systems only)

Parameter

ALMOUT=b

FRAMING =b

Value b = AIS

Parameter Description

Output is AIS during alarm b = SQUELCH Output is squelched during alarm b = SSM Outputs are at ‘STU’ quality level for

ESF framing and at ‘SSUT’ quality level for CAS4 and CCS4 framing during holdover alarm (SSM requires CAS4,

CCS4,or ESF output framing) b = CAS b = CAS4 b = CCS b = CCS4 b = D4 b = ESF b = NONE

Output framing is CAS

Output framing is CAS4

Output framing is CCS

Output framing is CCS4

Output framing is D4

Output framing is ESF

Output framing is NONE (analog)

(If ALMOUT is SQUELCH, the signal turns off during holdover alarm. Any other ALMOUT option does not affect output during alarm)

2

5

TimeSource 3500

TL1 Reference

097-72050-01 Issue 7: August 2003

197

4

S S S S S S S S S S S S S S

Edit Equipment (cont’d)

S S S S S S S S S S S S S S S

Aid

OPT-a

(990-

72050-07 systems only)

Parameter

ALMOUT=b

FRAMING =b

Value b = AIS

Parameter Description

Output is AIS during alarm b = SQUELCH Output is squelched during alarm b = SSM Outputs are at ‘STU’ quality level during holdover alarm (SSM requires

ESF output framing) b = D4 b = ESF b = CCK

Output framing is D4

Output framing is ESF

Output is Composite Clock. (ALMOUT is SQUELCH by default and need not be programmed. ALMOUT cannot be set to AIS or SSM. The signal turns off during holdover alarm.)

198

TimeSource 3500

TL1 Reference

097-72050-01 Issue 7: August 2003

S S S S S S S S S S S S S S S

Edit Equipment (cont’d)

S S S S S S S S S S S S S S

Aid

TS3500

Parameter

DCDPASSTHRU

DCDUSERPORT=x

(See Note 8)

Value

INH

ALW1

ALW2 x = 1 x = 2 x = 3 or

5001,

5002,

5003,

5004

Description

DCD port communication is inhibited

COM1 is the DCD interface port

COM2 is the DCD interface port

COM1

COM2

COM3 or IP port 5001 to 5004

2

Notes:

1. This parameter affects all Ethernet ports. Close the Ethernet ports and log off all users before issuing a command with this parameter.

2. Port 5550 makes a connection to this element manager to send

TL1 autonomous messages, and closes the connection when the transmission is complete.

3. Port 5551 accepts a connection from this element manager for

TL1 commands and responses.

4. When the TimeSource 3500 uses a roof antenna, only the parameters ANTCBLDLY and ANTELEVMASK, and the mode

ANTMODE=AUTO, are allowed.

5

TimeSource 3500

TL1 Reference

097-72050-01 Issue 7: August 2003

199

4

S S S S S S S S S S S S S S S S S S S S S S S S S S

Edit Equipment (cont’d)

Notes:

S S S

5. If the dbinit jumper is changed, the NTP password has to be reentered.

6. A span must have been put into service using the ENT-EQPT command before setting the ENSEMBLER and SSM parameters.

7. When setting alarm integration time (SEVERITY or SERAFF), the type of alarm (HOLDOVER, GPS, LOS, AIS, or ERROR) has to be specified. For example, ED-EQPT::TS3500:CTAG:::

ALARM=HOLDOVER, TIME=72-00, SEVERITY1=EV,

SERAFF1=NSA, SEVERITY2=MJ, SERAFF2=SA; will generate a holdover event as soon as the condition is detected with an NSA flag. Once this condition has existed for 72 hours, TS3500 will generate a major alarm with an SA flag. These parameters can then be verified using the RTRV-EQPT command.

8. All commands on DCDUSERPORT having TID which equals

SID of the DCD are forwarded to the DCD. Similarly, the responses from the DCD are sent to the provisioned

DCDUSERPORT.

Response Format:

<sid> <date> <time>

M <ctag> COMPLD

/*LINK:<link>,CMD:<command>*/

;

200

TimeSource 3500

TL1 Reference

097-72050-01 Issue 7: August 2003

S S S S S S S S S S S S S S S S S S S S S S S S S S S S S

Enter Equipment

This command puts optional inputs in service, and causes the selected input to be monitored. Additionally, this command can cause an input to be ensembled. All in-service inputs are monitored. The Delete Equipment command must be used to take an input out of service. The command format is:

ENT-EQPT:[<tid>]:<aid>:<ctag>:::<spec_block>;

2

SPAN-a

Aid Value a = A a = B

Item Addressed

T1 span A input

T1 span B input

TimeSource 3500

TL1 Reference

097-72050-01 Issue 7: August 2003

201

5

S S S S S S S S S S S S S S S S S S S S S S S S S S S S

Enter Equipment (cont’d)

The parameters which can be entered in the <spec_block> are listed below. For any specific <aid> entered in a command, only certain parameters are valid. For each valid parameter, choose the appropriate value from the Value column. When entering multiple parameters, separate the parameters with commas .

S

4

Aid

SPAN-a

Parameter

ENSEMBLER=b

Value b = ALW b = INH

Description

Span is monitored and ensembled

Span is monitored, but not ensembled

Example to set an input to be monitored, but not ensembled:

ENT-EQPT:[<tid>]:SPAN-A:<ctag>;

Example to set an input to be monitored and ensembled:

ENT-EQPT:[<tid>]:SPAN-A:<ctag>:::ENSEMBLER=ALW;

Response Format:

<sid> <date> <time>

M <ctag> COMPLD

/*LINK:<link>,CMD:<command>*/

;

202

TimeSource 3500

TL1 Reference

097-72050-01 Issue 7: August 2003

S S S S S S S S S S S S S S S S S S S S S S S S S S S S S

Enter User Security

This command allows a system administrator to enter a new user, and the new user’s user name, password, and access level. The command format is:

ENT-USER-SECU:[<tid>]:<uid>:<ctag>::<pid>,,<uap>;

Parameter

<uid>

<pid>

<uap>

Parameter Description

User name – must start with an alpha character and have a maximum of 10 characters.

Password – has to be a minimum of 8 characters and a maximum of 10 characters. It must contain at least one digit and one of the following characters: ! $ % ' (

) * + . / < > ? @

Password cannot be the same as User ID even if extra characters are appended to password at the end.

Access level (1 to 5). Levels 1 to 4 do not allow the user to enter or delete users. Level 5 allows the user to enter or delete users.

2

Command Example:

ENT-USER-SECU::TELECOM:<ctag>::TS3000!!,,1;

Response Format:

<sid> <date> <time>

M <ctag> COMPLD

/*LINK:<link>,CMD:<command>*/

;

TimeSource 3500

TL1 Reference

097-72050-01 Issue 7: August 2003

203

5

4

204

S S S S S S S S S S S S S S S S S S S S S S S S S S

Initialize Log

This command clears the alarm log. The command format is:

INIT-LOG:[<tid>]::<ctag>::almlog;

S S S

Response Format:

<sid> <date> <time>

M <ctag> COMPLD

/*LINK:<link>,CMD:<command>*/

;

TimeSource 3500

TL1 Reference

097-72050-01 Issue 7: August 2003

S S S S S S S S S S S S S S S S S S S S S S S S S S S

Initialize Register

This command resets to zero all the performance monitoring associated with the entered aid. The command can be used to reset either span independently or both spans at the same time.

The command format is:

S S

INIT-REG-EQPT:[<tid>]:<aid>:<ctag>::ALL;

2

SPAN-a

Aid

ALL

Value a = A a = B

Item Addressed

T1 span A input

T1 span B input

T1 span A and span B inputs

Response Format:

<sid> <date> <time>

M <ctag> COMPLD

/*LINK:<link>,CMD:<command>*/

;

TimeSource 3500

TL1 Reference

097-72050-01 Issue 7: August 2003

205

5

4

S S S S S S S S S S S S S S S S S S S S S S S S S S S S

Initialize System

This command resets the specified processor.

Caution: Using this command with an <aid> of TS3500 will cause a loss of outputs until GPS satellites are reacquired if ALMOUT is

SQUELCH, or unstable outputs if ALMOUT is not SQUELCH.

S

The command format is:

INIT-SYS:[<tid>]:<aid>:<ctag>::1;

Aid

TS3500

GPS

Item Addressed

System software

GPS receiver software

Response Format:

<sid> <date> <time>

M <ctag> COMPLD

/*LINK:<link>,CMD:<command>*/

;

206

TimeSource 3500

TL1 Reference

097-72050-01 Issue 7: August 2003

S S S S S S S S S S S S S S S S S S S S S S S S S S S S S

Operate Alarm Cutoff All

This command deactivates (silences) the audible office alarm. The command format is:

OPR-ACO-ALL:[<tid>]:ALL:<ctag>;

Response Format:

<sid> <date> <time>

M <ctag> COMPLD

/*LINK:<link>,CMD:<command>*/

;

2

TimeSource 3500

TL1 Reference

097-72050-01 Issue 7: August 2003

207

5

4

S S S S S S S S S S S S S S S S S S S S S S S S S S S S

Retrieve Alarm All

This command displays all current system alarms. The command format is:

S

RTRV-ALM-ALL:[<tid>]:ALL:<ctag>;

If there are no alarms:

<sid> <date> <time>

M <ctag> COMPLD

/*LINK:<link>,CMD:<command>*/

;

If there is at least one alarm:

<sid> <date> <time>

M <ctag> COMPLD

"<aid>:<ntfcncde>,<condtype>,<srveff>,

<ocrdat>,<ocrtm>,,:\"<conddescr>\""...

/*LINK:<link>,CMD:<command>*/

;

Note:

Refer to the Troubleshooting chapter for a list of all

<conddescr> messages, and the recommended action.

208

TimeSource 3500

TL1 Reference

097-72050-01 Issue 7: August 2003

S S S S S S S S S S S S S S S S S S S S S S S S S S

Retrieve Alarm Equipment

This command displays current alarms for the specified equipment. The command format is:

S S S

RTRV-ALM-EQPT:[<tid>]:<aid>:<ctag>;

TS3500

SPAN-a

Aid

GPS

Value a = A

— a = B

Item Addressed

System (all TS3500 alarms)

T1 span A input

T1 span B input

GPS receiver

2

TimeSource 3500

TL1 Reference

097-72050-01 Issue 7: August 2003

209

5

4

S S S S S S S S S S S S S S S S S S S S

Retrieve Alarm Equipment (cont’d)

S S S S S S S S S

If there are no alarms:

<sid> <date> <time>

M <ctag> COMPLD

/*LINK:<link>,CMD:<command>*/

;

If there is at least one alarm:

<sid> <date> <time>

M <ctag> COMPLD

"<aid>:<ntfcncde>,<condtype>,<srveff>,

<ocrdat>,<ocrtm>,,:\"<conddescr>\""...

/*LINK:<link>,CMD:<command>*/

;

Note:

Refer to the Troubleshooting chapter for a list of all

<conddescr> messages, and the recommended action.

210

TimeSource 3500

TL1 Reference

097-72050-01 Issue 7: August 2003

S S S S S S S S S S S S S S S S S S S S S S S S S S S S S

Retrieve Communication

This command displays communication port parameter settings.

The command format is:

RTRV-COM:[<tid>]:<aid>:<ctag>;

COM-a

Aid Value a = 1 a = 2 a = 3 a = 5001 a = 5002 a = 5003 a = 5004 a = 5551

Item Addressed

Serial communication port 1

Serial communication port 2

Serial communication port 3

Ethernet user interface port 5001

Ethernet user interface port 5002

Ethernet user interface port 5003

Ethernet user interface port 5004

Ethernet element manager interface port 5551

All communication ports ALL

Response Format:

<sid> <date> <time>

M <ctag> COMPLD

"<aid>:::<spec_block>"...

/*LINK:<link>,CMD:<command>*/

;

2

5

TimeSource 3500

TL1 Reference

097-72050-01 Issue 7: August 2003

211

4

S S S S S S S S S S S S S S S S S S S S S S S S S S S S

Retrieve Communication (cont’d)

The parameters which may be displayed in the <spec_block> are listed below.

S

Parameter

MONMSG=a

KEEPALIVE=a

ENDOFTEXT=a

ECHO=a

COMPRI=a

Value a = INH a = ALW0 a = ALW1

Description a = ALW a = INH

View messages from all ports

View messages from this port only a = 1 to 255 Inactive minutes until the unit sends a

COMPLD message to keep the connection from being closed a = 0 No COMPLD message is output a = 1 to 9F Hex code at end of all responses a = 00 a = ALW

No hex code at end of responses

Echoes characters received so they appear on the user’s screen as typed

Local echo is disabled

TL1 commands and responses, no autonomous messages sent

TL1 commands and responses, sends autonomous messages a = ALW2 a = INH

TL1 commands and responses, sends autonomous messages whether or not logged on

Closes connection, logs off a user (if logged on), and keeps port from use

(a port cannot close itself)

212

TimeSource 3500

TL1 Reference

097-72050-01 Issue 7: August 2003

S S S S S S S S S S S S S S S S S S S

Retrieve Communication (cont’d)

S S S S S S S S S S

Parameter Value Parameter Description

AUTOLOGOFF=a a = 1 to 255 Inactive minutes until the unit logs off the user, keeping the connection open a = 0 Autologoff is disabled

SWCONTROL=a a = ALW a = INH

HWCONTROL=a a = ALW a = INH

XON/XOFF flow control is enabled

XON/XOFF flow control is not enabled

Serial port CTS/RTS flow control is enabled

Serial port CTS/RTS flow control is not enabled

BAUD=a

PARITY=a a = 115 a = 57.6

a = 38.4

a = 19.2

a = 9600 a = 4800 a = 2400 a = EVEN a = ODD

Serial port baud rate is 115 kbaud

Serial port baud rate is 57.6 kbaud

Serial port baud rate is 38.4 kbaud

Serial port baud rate is 19.2 kbaud

Serial port baud rate is 9600 baud

Serial port baud rate is 4800 baud

Serial port baud rate is 2400 baud

Even parity bit is enabled

Odd parity bit is enabled

STOP=a a = NONE Parity bit is disabled a = 1 1 stop bit a = 2 2 stop bits

2

5

TimeSource 3500

TL1 Reference

097-72050-01 Issue 7: August 2003

213

4

S S S S S S S S S S S S S S S S S S S S S S S S S S S S

Retrieve Condition All

This command displays all current system alarms and events. The command format is:

S

RTRV-COND-ALL:[<tid>]:ALL:<ctag>;

If there are no alarms or events:

<sid> <date> <time>

M <ctag> COMPLD

/*LINK:<link>,CMD:<command>*/

;

If there is at least one alarm or event:

<sid> <date> <time>

M <ctag> COMPLD

"<aid>:<ntfcncde>,<condtype>,<srveff>,

<ocrdat>,<ocrtm>,,,:\"<conddescr>\""...

/*LINK:<link>,CMD:<command>*/

;

Note:

Refer to the Troubleshooting chapter for a list of all

<conddescr> messages, and the recommended action.

214

TimeSource 3500

TL1 Reference

097-72050-01 Issue 7: August 2003

S S S S S S S S S S S S S S S S S S S S S S S S S S

Retrieve Condition Equipment

This command displays current alarms and events for the specified equipment. The command format is:

S S S

RTRV-COND-EQPT:[<tid>]:<aid>:<ctag>;

TS3500

SPAN-a

Aid

GPS

Value a = A

— a = B

Item Addressed

System

T1 span A input

T1 span B input

GPS receiver

Command Example:

RTRV-COND-EQPT::TS3500:<ctag>;

2

TimeSource 3500

TL1 Reference

097-72050-01 Issue 7: August 2003

215

5

4

S S S S S S S S S S S S S S S S S S S S S S

Retrieve Condition Equipment (cont’d)

S S S S S S S

If there are no alarms:

<sid> <date> <time>

M <ctag> COMPLD

/*LINK:<link>,CMD:<command>*/

;

If there is at least one alarm:

<sid> <date> <time>

M <ctag> COMPLD

"<aid>:<ntfcncde>,<condtype>,<srveff>,

<ocrdat>,<ocrtm>,,,\"<conddescr>\""...

/*LINK:<link>,CMD:<command>*/

;

Note:

Refer to the Troubleshooting chapter for a list of all

<conddescr> messages, and the recommended action.

216

TimeSource 3500

TL1 Reference

097-72050-01 Issue 7: August 2003

S S S S S S S S S S S S S S S S S S S S S S S S S S

Retrieve Equipment

This command displays parameter settings for the specified equipment. The command format is:

S S S

RTRV-EQPT:[<tid>]:<aid>:<ctag>;

ALL

TS3500

GPS

SPAN-a

Aid

T1-a

OPT-a

Value

— a = A

— a = B a = A a = B a = 1 to 8

Item Addressed

All aids for this command

System

GPS receiver

Span A input

Span B input

T1 A output

T1 B output

T1 1 through 8 outputs option

(990-72050-02 systems only)

T1 or E1 outputs option

(990-72050-06 systems only)

T1 or CCK outputs option

(990-72050-07 systems only)

Command Example:

RTRV-EQPT::ALL:G;

2

5

TimeSource 3500

TL1 Reference

097-72050-01 Issue 7: August 2003

217

S S S S S S S S S S S S S S S S S

Retrieve Equipment (cont’d)

S S S S S S S S S S S S

Response Format:

<sid> <date> <time>

M <ctag> COMPLD

"<aid>::::<spec_block>"...

/*LINK:<link>,CMD:<command>*/

;

4

The parameters which may be displayed in the <spec_block> are listed below.

Aid Parameter

TS3500 TOD=a

ALMCOND=a

IPNE=a.b.c.d

IPSUBNET=a.b.c.d

Value a = CISCO a = NTP4 a = NONE a = ALW

Parameter Description

Serial message sent is Cisco format

Serial message sent is NTP Type 4 format

No serial message is sent

Alarm conditioning for outputs is enabled a = INH Alarm conditioning for outputs is disabled a = 0 to 255 This unit’s IP address b = 0 to 255 c = 0 to 255 d = 0 to 255 a = 0 to 255 Subnetwork mask b = 0 to 255 c = 0 to 255 d = 0 to 255

218

TimeSource 3500

TL1 Reference

097-72050-01 Issue 7: August 2003

S S S S S S S S S S S S S S S S

Retrieve Equipment (cont’d)

S S S S S S S S S S S S S

Aid Parameter Value Parameter Description

TS3500

(cont’d)

IPGATE=a.b.c.d a = 0 to 255 Default gateway IP address b = 0 to 255 c = 0 to 255 d = 0 to 255

IPEM1=a.b.c.d a = 0 to 255 Primary element manager IP address

IPEM1PORT=a

IPEM2=a.b.c.d a = 0 to 255 Alternate element manager IP address b = 0 to 255 c = 0 to 255 d = 0 to 255

IPEM2PORT=a a = 0 to

65535

IPINACT=a a = 0 to

10000

IPNTP=a b = 0 to 255 c = 0 to 255 d = 0 to 255 a = 0 to

65535 a = ALW

Primary element manager output port number

Alternate element manager port number

Port 5550 closes the connection to the

Element Manager if no autonomous messages are sent during this number of

100-ms units (0 to 10,000, where 0 deactivates the timer, for example,

100 = 10 s)

SNTP feature activated

2

5

TimeSource 3500

TL1 Reference

097-72050-01 Issue 7: August 2003

219

4

S S S S S S S S S S S S S S S S S

Retrieve Equipment (cont’d)

S S S S S S S S S S S S

Aid

TS3500

(cont’d)

GPS

Parameter

DCDPASSTHRU

DCDUSERPORT=a

(See Note 1)

INH

Value

ALW1

ALW2 a = 1 a = 2

COM2 is the DCD interface port

COM1

COM2

Parameter Description

DCD port communication is inhibited

COM1 is the DCD interface port

COM3 or IP port 5001 to 5004

ANTCBLDLY=a a = 0 to 330 Antenna cable length (meters)

ANTELEVMASK=a a = 0 to 45 Antenna elevation mask angle

(degrees)

ANTMODE=a a = 3 or

5001, 5002,

5003, 5004 a = AUTO Automatic survey-in mode a = MANUAL Manual survey-in mode (do not use for roof antenna)

MANLAT=a-b-c-d a = N a = S

North latitude

South latitude b = 1 to 180 Degrees of latitude c = 1 to 60 Minutes of latitude d = 1 to

1000

Decimal minutes of latitude

220

TimeSource 3500

TL1 Reference

097-72050-01 Issue 7: August 2003

S S S S S S S S S S S S S S S S

Retrieve Equipment (cont’d)

S S S S S S S S S S S S S

Aid

GPS

(cont’d)

Parameter

MANLONG= a-b-c-d

SPAN-a

T1-a

MANELEV=a

ENSEMBLER=b

MONITOR=b

SSM=b

FRAMING=b

ALMOUT=b

TimeSource 3500

TL1 Reference

097-72050-01 Issue 7: August 2003

Value Parameter Description a = E a = W

East longitude

West longitude b = 1 to 180 Degrees of longitude c = 1 to 60 Minutes of longitude d = 1 to

1000

Decimal minutes of longitude a = –1000 to 8000 b = ALW

Antenna elevation (meters)

T1 span is ensembled b = INH b = ALW b = INH b = ALW b = INH b = ESF b = D4 b = AIS b =

SQUELCH b = SSM

T1 span is not ensembled

T1 span is monitored

T1 span is not monitored

SSM message is used to qualify input

SSM message is not used to qualify input

Output framing is ESF

Output framing is D4

Output is AIS during alarm

Output is squelched during alarm

Outputs are at ‘STU’ quality level during holdover alarm (SSM requires

ESF output framing)

221

2

5

S S S S S S S S S S S S S S S S S

Retrieve Equipment (cont’d)

S S S S S S S S S S S S

Aid Parameter

TS3500 ALARM=x

SPAN

A & B

ALARM=x

Value Parameter Description x = HOLDOVER HOLDOVER alarm x = GPS x = LOS x = AIS

GPS alarm

LOS alarm

AIS alarm x = ERROR ERROR alarm

4

TS3500,

SPAN

A & B

TIME=x

SEV1=x

(See Note 2)

SEV2=x

(See Note 2) x = HH-MM x = 0 x = CR x = MJ x = MN x = EV x = NA x = CR x = MJ x = MN x = EV x = NA

Hour (00-999) and minute (00-59) time to escalate alarm

No alarm escalation

Severity of initial alarm prior to escalation

Severity of escalated alarm

222

TimeSource 3500

TL1 Reference

097-72050-01 Issue 7: August 2003

S S S S S S S S S S S S S S S S

Retrieve Equipment (cont’d)

S S S S S S S S S S S S S

Aid

TS3500,

SPAN

A & B,

(cont’d)

OPT-a

(990-

72050-

02 systems only)

Parameter

SAFF1=x

(See Note 2)

SAFF2=x

(See Note 2)

Value x = SA x = NSA x = SA x = NSA

ALMOUT=b b = AIS b = SQUELCH b = SSM

FRAMING=b b = ESF b = D4

Parameter Description

Service affecting state of initial alarm prior to escalation

Service affecting state of escalated alarm

Output is AIS during alarm

Output is squelched during alarm

Outputs are at ‘STU’ quality level during holdover alarm (SSM requires ESF output framing)

Output framing is ESF

Output framing is D4

2

TimeSource 3500

TL1 Reference

097-72050-01 Issue 7: August 2003

223

5

S S S S S S S S S S S S S S S S S

Retrieve Equipment (cont’d)

S S S S S S S S S S S S

4

Aid

OPT-a

(990-

72050-06 systems only)

Parameter

ALMOUT=b

FRAMING =b

Value b = AIS

Parameter Description

Output is AIS during alarm b = SQUELCH Output is squelched during alarm b = SSM Outputs are at ‘STU’ quality level for

ESF framing and at ‘SSUT’ quality level for CAS4 and CCS4 framing during holdover alarm (SSM requires CAS4,

CCS4,or ESF output framing) b = CAS b = CAS4 b = CCS b = CCS4 b = D4 b = ESF b = NONE

Output framing is CAS

Output framing is CAS4

Output framing is CCS

Output framing is CCS4

Output framing is D4

Output framing is ESF

Output framing is NONE (analog)

(If ALMOUT is SQUELCH, the signal turns off during holdover alarm. Any other ALMOUT option does not affect output during alarm)

224

TimeSource 3500

TL1 Reference

097-72050-01 Issue 7: August 2003

S S S S S S S S S S S S S S S S

Retrieve Equipment (cont’d)

S S S S S S S S S S S S S

Aid

OPT-a

(990-

72050-07 systems only)

Parameter

ALMOUT=b

FRAMING =b

Value b = AIS

Parameter Description

Output is AIS during alarm b = SQUELCH Output is squelched during alarm b = SSM Outputs are at ‘STU’ quality level during holdover alarm (SSM requires

ESF output framing) b = D4 b = ESF b = CCK

Output framing is D4

Output framing is ESF

Output is Composite Clock. (ALMOUT is SQUELCH by default and need not be programmed. ALMOUT cannot be set to AIS or SSM. The signal turns off during holdover alarm.)

2

TimeSource 3500

TL1 Reference

097-72050-01 Issue 7: August 2003

225

5

4

S S S S S S S S S S S S S S S S S S S S S S S S S S S S

Retrieve Equipment (cont’d)

Notes:

S

1. All commands on DCDUSERPORT TID which equal SID of the

DCD are forwarded to the DCD. Similarly, the responses from the DCD are sent to the provisioned DCDUSERPORT.

2. When setting alarm integration time (SEVERITY or SERAFF), the type of alarm (HOLDOVER, GPS, LOS, AIS, or ERROR) has to be specified. For example, ED-EQPT::TS3000:CTAG:::

ALARM=HOLDOVER, TIME=72-00, SEVERITY1=EV,

SERAFF1=NSA, SEVERITY2=MJ, SERAFF2=SA; will generate a holdover event as soon as the condition is detected with an NSA flag. Once this condition has existed for 72 hours, TS3000 will generate a major alarm with an SA flag. These parameters can then be verified using the RTRV-EQPT command.

226

TimeSource 3500

TL1 Reference

097-72050-01 Issue 7: August 2003

S S S S S S S S S S S S S S S S S S S S S S S S S S S S S

Retrieve GPS Status

This command displays the position of the GPS receiver, UTC time, and status information for each of the GPS satellites in view. The command format is:

RTRV-GPS-STAT:[<tid>]:GPS:<ctag>;

Response Format:

<sid> <date> <time>

M <ctag> COMPLD

"<aid>:LAT=a,LONG=a,ALT=a,UTC=a

ANTMODE=a,MERIT=a,SUCCESS=a%

SAT-a,USE=a,CNO=a,ELEV=a,AZ=a,

LOCK=a..."

/*LINK:<link>,CMD:<command>*/

;

2

TimeSource 3500

TL1 Reference

097-72050-01 Issue 7: August 2003

227

5

4

S S S S S S S S S S S S S S S S S

Retrieve GPS Status (cont’d)

S S S S S S S S S S S S

LAT=a

Parameter

LONG=a

ALT=a

UTC=a

ANTMODE=a

MERIT=a

SUCCESS=a

SAT=a

USE=a

CNO=a

ELEV=a

AZ=a

LOCK=a

228

Value a = dd.mm.fffN

a = dd.mm.fffS

a = ddd.mm.fffE

Description

Current latitude north in degrees, minutes, and decimal-fractions of a minute

Current latitude south in degrees, minutes, and decimal-fractions of a minute

Current longitude east in degrees, minutes, and decimal-fractions of a minute a = ddd.mm.fffW

Current longitude west in degrees, minutes, and decimal-fractions of a minute a = mm.mmm

Altitude in meters to the thousandth of a meter, referenced to mean sea level a = hh-mm-ss a = AUTO a = MANUAL a = bbb

Universal Coordinated Time (UTC), where hh is hours (00 to 23), mm is minutes (00 to

59), and ss is seconds (00 to 59)

Automatic survey-in mode

Manual survey-in mode

Timing error estimate in ns a = bb a = 1 to 25 a = Y a = N a = nn a = dd a = ddd a = 1 to 2500

Percentage of time satellites are visible

Satellite identification number

Satellite in use

Satellite not in use

Satellite carrier-to-noise ratio

Satellite elevation in degrees

Satellite azimuth in degrees

Seconds since the receiver locked to the satellite carrier

TimeSource 3500

TL1 Reference

097-72050-01 Issue 7: August 2003

S S S S S S S S S S S S S S S S S S S S S S S S S S S

Retrieve Header

This command allows for NMA integration to use as a keep alive message. The command format is:

S S

RTRV-HDR:[<tid>]::<ctag>;

Response Format:

RTRV-HDR:::114;

TELECOM1 1997-12-08 15:04:13

M 114 COMPLD

2

TimeSource 3500

TL1 Reference

097-72050-01 Issue 7: August 2003

229

5

4

S S S S S S S S S S S S S S S S S S S S S S S

Retrieve Inventory

S S

This command displays information about the specified equipment. The command format is:

S S S S

RTRV-INVENTORY:[<tid>]:TS3500:<ctag>;

Response Format:

<sid> <date> <time>

M <ctag> COMPLD

"TS3500::::CARD=TS3500,

MACID=a,

TYPE=a,

PART=a,

SERIAL=a,

SOFTVER_TS3000=a,

SOFTVER_GPS=a,

SOFTVER_DEV=a"

/*LINK: x, CMD:<command>*/

;

230

TimeSource 3500

TL1 Reference

097-72050-01 Issue 7: August 2003

S S S S S S S S S S S S S S S S

Retrieve Inventory (cont’d)

S S S S S S S S S S S S S

Parameter

CARD=TS3500

Value

MACID=a.b.c.d.e a = 00 to FF in hexadecimal format

TYPE=a b = 00 to FF in hexadecimal format c = 00 to FF in hexadecimal format d = 00 to FF in hexadecimal format e = 00 to FF in hexadecimal format a = NO OPTION

BOARD a = T1 OPTION

BOARD a = CCK OPTION

BOARD a = IRIG OPTION

BOARD

PART=a

SERIAL=a a = MIXED E1/T1

OPTION BOARD a = MIXED T1/CCK

OPTION BOARD

System

MAC address

Description

TimeSource 3500 (standard)

(990-72050-01 systems)

TimeSource 3500 with eight additional T1 outputs (990-72050-02 systems)

TimeSource 3500 with eight composite clock outputs (990-72050-03 systems)

TimeSource 3500 with two TOD IRIG-B outputs (990-72050-05 systems)

TimeSource 3500 with eight mixed E1/T1 outputs (990-72050-06 systems)

TimeSource 3500 with eight mixed

T1/CCK outputs (990-72050-07 systems) a = Part number a = Serial number

2

5

TimeSource 3500

TL1 Reference

097-72050-01 Issue 7: August 2003

231

4

232

S S S S S S S S S S S S S S S S S

Retrieve Inventory (cont’d)

S S S S S S S S S S S S

Parameter

SOFTVER_

TS3000=a

Value a = bb.cc.dd

SOFTVER_GPS=a a = bb.cc.dd

SOFTVER_

DEV=a a = bb.cc.dd or bb.cc.dd-ee.ff.gg

Description

System software version

GPS receiver software version

Device software version

TimeSource 3500

TL1 Reference

097-72050-01 Issue 7: August 2003

S S S S S S S S S S S S S S S S S S S S S S S S S S S

Retrieve Log

This command retrieves the alarm log. The command format is:

RTRV-LOG:[<tid>]::<ctag>::almlog;

S S

Response Format:

<sid> <date> <time>

M <ctag> COMPLD

"<logtype>"

"<aid>:<ntfcncde>,<condtype>,<srverff>,

<ocrdat>,<ocrtm>,,[,]:<conddescr>,

[:<dgntype>]"*/

/*LINK:<link>,CMD:<command>*/

;

2

Parameter

<ntfcncde>

<condtype>

<srverff>

<ocrdat>

Parameter Description

Severity of alarm: critical, major, or minor

Single type of alarm condition being reported on this particular line, i.e., LOS, FAIL, TBD for each alarm

Alarm is service affecting (SA) or non-service affecting

(NSA)

Occurrence date in MOY-DOM format, where

MOY=1 to 12 and DOM=1 to 31

<ocrtm> Occurrence Time of Day in HOD-MOH-SOM format, where HOD=0 to 23, MOH=0 to 59, SOM=0 to 59

<conddescr> Text string of no more than 64 characters enclosed within a pair of escape quotes (\)

<dgntype> TL1 identifier up to 16 characters in length

5

TimeSource 3500

TL1 Reference

097-72050-01 Issue 7: August 2003

233

4

S S S S S S S S S S S S S S S S S S S S S S S S S S S S

Retrieve Performance Monitoring

This command retrieves the performance monitoring data from the

TimeSource 3500. This data includes MTIE, TDEV, PHASE1S, and

PHASE1M. For current 24 hour data, MTIE, TDEV, and PHASE1S data are grouped every 15 minutes. In addition, there are 7 daily summaries of MTIE, TDEV, and PHASE1M. Each value type can be retrieved for both span inputs A and B.

S

MTIE data includes the following time intervals in seconds: 1, 4,

10, 40, 100, 300, 900, 1800, 3600, 7200, 14400, 28800, and

86400.

TDEV data includes the following time intervals in seconds: 1, 2,

4, 8, 16, 32, 64, 128, 256, 512, and 1024.

PHASE1S data includes 900 seconds of phase values.

PHASE1M data includes 60 minutes of phase values.

The command format is:

RTRV-PM-EQPT:[<tid>]:SPAN-a:<ctag>::<montype>

,,,,,[<mondat>][<montm>];

234

TimeSource 3500

TL1 Reference

097-72050-01 Issue 7: August 2003

S S S S S S S S S S S S S S S S S S S S S S S S

Retrieve Performance Monitoring (cont’d)

S S S S S

Parameter

SPAN-a

<montype>

<mondat>=x

<montm>=x a = A

Value a = B

MTIE

TDEV

PHASE1S

PHASE1M x = 1 to 12 x = 1 to 31 x = 0 to 23 x = 0 to 59

Description

E1 span A input

E1 span B input

MTIE data reported

TDEV data reported

1-second phase data reported

1-minute phase data reported

Monitor date, month of the year

Monitor date, day of the month

Monitor time, hour past midnight

Monitor time, minutes past the hour

2

MTIE Response Format:

<sid> <date> <time>

M <ctag>COMPLD

"SPAN-a:MTIE-a,<monval>,<vldty>

,,,,<mondat>,<montm>"

.

.

.

.

.

.

"SPAN-a:MTIE-a,<monval>,<vldty>

,,,,<mondat>,<montm>"

/*LINK:<link>,CMD:<command>*/

.

.

.

; 5

TimeSource 3500

TL1 Reference

097-72050-01 Issue 7: August 2003

235

4

S S S S S S S S S S S S S S S S S S S S S S S S S S S

Retrieve Performance Monitoring (cont’d)

Note:

MTIE Data types:

S S

• One 15 minute bin from the last 24 hours of data. To select a 15 minute bin, enter mondat and montm. Any mondat/ montm combination outside of the past 24 hour window is denied. Any time increment may be entered. The system rounds the value to the nearest bin. Entered minutes of

1 to 15 correspond to the first 15 minute bin, 16 to 30 correspond to the second 15 minute bin, etc.

• One day summary from the last 7 days of daily summaries.

To select one daily summary, enter mondat, but do not enter montm. Any mondat not in the previous 7 day window is denied.

236

TimeSource 3500

TL1 Reference

097-72050-01 Issue 7: August 2003

S S S S S S S S S S S S S S S S S S S S S S S S

Retrieve Performance Monitoring (cont’d)

S S S S S

Parameter

SPAN-a

MTIE-a

<monval>

<vldty>

MONDAT=a-b

MONTM=a-b a = A

Value a = B a = 1S, 2S, 4S,

10S, 40S,

100S, 300S,

900S, 1800S,

3600S,

7200S,

14400S,

28800S, or

86400S

One 15 min bin from the last 24 h of data

COMPL

NA a = 1 to 12 b = 1 to 31 a = 0 to 23 b = 0 to 59

Description

E1 span A input

E1 span B input

MTIE monitored type, where a is time intervals in seconds

Monitored value

Data is valid

Data is not valid

Monitor date, month of the year

Monitor date, day of the month

Monitor time, hour of the day

Monitor time, minute of the hour

2

5

TimeSource 3500

TL1 Reference

097-72050-01 Issue 7: August 2003

237

4

S S S S S S S S S S S S S S S S S S S S S S S

Retrieve Performance Monitoring (cont’d)

MTIE Response Example:

TS3500-2009 2000-05-25 11:01:58

M G COMPLD

"SPAN-A:MTIE-1S,1,COMPL

,,,,,2000-05-25,11-00-00"

"SPAN-A:MTIE-4S,1,COMPL

,,,,,2000-05-25,11-00-00"

"SPAN-A:MTIE-10S,1,COMPL

,,,,,2000-05-25,11-00-00"

"SPAN-A:MTIE-40S,1,COMPL

,,,,,2000-05-25,11-00-00"

"SPAN-A:MTIE-100S,1,COMPL

,,,,,2000-05-25,11-00-00"

"SPAN-A:MTIE-300S,1,COMPL

,,,,,2000-05-25,11-00-00"

"SPAN-A:MTIE-900S,1,COMPL

,,,,,2000-05-25,11-00-00"

"SPAN-A:MTIE-1800S,1,COMPL

,,,,,2000-05-25,11-00-00"

"SPAN-A:MTIE-3600S,1,COMPL

,,,,,2000-05-25,11-00-00"

"SPAN-A:MTIE-7200S,1,COMPL

,,,,,2000-05-25,11-00-00"

"SPAN-A:MTIE-14400S,1,COMPL

,,,,,2000-05-25,11-00-00"

"SPAN-A:MTIE-28800S,1,COMPL

,,,,,2000-05-25,11-00-00"

"SPAN-A:MTIE-86400S,1,COMPL

,,,,,2000-05-25,11-00-00"

/*LINK:5002,CMD:RTRV-PM-EQPT::

SPAN-A:G::MTIE*/

;

S S S S S S

238

TimeSource 3500

TL1 Reference

097-72050-01 Issue 7: August 2003

S S S S S S S S S S S S S S S S S S S S S S S S

Retrieve Performance Monitoring (cont’d)

S S S S S

TDEV Response Format:

<sid> <date> <time>

M <ctag>COMPLD

"SPAN-a:TDEV-a,<monval>,<vldty>

,,,,<mondat>,<montm>"

.

.

.

.

.

.

"SPAN-a:TDEV-a,<monval>,<vldty>

,,,,<mondat>,<montm>"

/*LINK:<link>,CMD:<command>*/

.

.

.

;

Note: TDEV Data types:

• One 15 minute bin from the last 24 hours of data. To select a 15 minute bin, enter mondat and montm. Any mondat/ montm combination outside of the past 24 hour window is denied. Any time increment may be entered. The system rounds the value to the nearest bin. Entered minutes of

1 to 15 correspond to the first 15 minute bin, 16 to 30 correspond to the second 15 minute bin, etc.

• One day summary from the last 7 days of daily summaries.

To select one daily summary, enter mondat, but do not enter montm. Any mondat not in the previous 7 day window is denied.

2

5

TimeSource 3500

TL1 Reference

097-72050-01 Issue 7: August 2003

239

4

S S S S S S S S S S S S S S S S S S S S S S S

Retrieve Performance Monitoring (cont’d)

S S S S S S

Parameter

SPAN-a

TDEV=a

<monval>

<vldty>

MONDAT=a-b

MONTM=a-b

Value a = A a = B a = 1S, 2S, 4S,

8S, 16S, 32S,

64S, 128S,

256S, 512S, or

1024S

One 15 min bin from the last 24 h of data

COMPL

NA a = 1 to 12 b = 1 to 31 a = 0 to 23 b = 0 to 59

Item Addressed

E1 span A input

E1 span B input

TDEV monitored type, where a is time intervals in seconds

Monitored value

Data is valid

Data is not valid

Monitor date, month of the year

Monitor date, day of the month

Monitor time, hour of the day

Monitor time, minute of the hour

240

TimeSource 3500

TL1 Reference

097-72050-01 Issue 7: August 2003

S S S S S S S S S S S S S S S S S S S S S S S S

Retrieve Performance Monitoring (cont’d)

S S S S S

TDEV Response Example:

TS3500-2009 2000-05-25 11:01:58

M G COMPLD

"SPAN-A:TDEV-1S,0,COMPL

,,,,,2000-05-25,11-00-00"

"SPAN-A:TDEV-2S,0,COMPL

,,,,,2000-05-25,11-00-00"

"SPAN-A:TDEV-4S,0,COMPL

,,,,,2000-05-25,11-00-00"

"SPAN-A:TDEV-8S,0,COMPL

,,,,,2000-05-25,11-00-00"

"SPAN-A:TDEV-16S,0,COMPL

,,,,,2000-05-25,11-00-00"

"SPAN-A:TDEV-32S,0,COMPL

,,,,,2000-05-25,11-00-00"

"SPAN-A:TDEV-64S,0,COMPL

,,,,,2000-05-25,11-00-00"

"SPAN-A:TDEV-128S,0,COMPL

,,,,,2000-05-25,11-00-00"

"SPAN-A:TDEV-256S,0,COMPL

,,,,,2000-05-25,11-00-00"

"SPAN-A:TDEV-512S,0,COMPL

,,,,,2000-05-25,11-00-00"

"SPAN-A:TDEV-1024S,0,COMPL

,,,,,2000-05-25,11-00-00"

/*LINK:5002,CMD:RTRV-PM-EQPT::

SPAN-A:G::TDEV*/

;

2

5

TimeSource 3500

TL1 Reference

097-72050-01 Issue 7: August 2003

241

4

S S S S S S S S S S S S S S S S S S S S S S S

Retrieve Performance Monitoring (cont’d)

S S S S S S

PHASE1S Response Format:

<sid> <date> <time>

M <ctag>COMPLD

"SPAN-a:PHASE1S,<monval>,< ∆ >,< ∆ >,< ∆ >,< ∆ >,

< ∆ >,< ∆ >,< ∆ >,< ∆ >,< ∆ >,< ∆ >,< ∆ >,< ∆ >,< ∆ >,< ∆ >,< ∆ >,

< ∆ >,< ∆ >,< ∆ >,< ∆ >,< ∆ >,< ∆ >,< ∆ >,< ∆ >,< ∆ >,< ∆ >,< ∆ >,

< ∆ >,< ∆ >,< ∆ >,< ∆ >,< ∆ >,< ∆ >,< ∆ >,< ∆ >,< ∆ >,< ∆ >,< ∆ >,

< ∆ >,< ∆ >,< ∆ >,< ∆ >,< ∆ >,< ∆ >,< ∆ >,< ∆ >,< ∆ >,< ∆ >,< ∆ >,

< ∆ >,< ∆ >,< ∆ >,< ∆ >,< ∆ >,< ∆ >,< ∆ >,< ∆ >,< ∆ >,< ∆ >,< ∆ >,

< ∆ >,< ∆ >,< ∆ >,< ∆ >,< ∆ >,< ∆ >,< ∆ >,< ∆ >,< ∆ >,< ∆ >,< ∆ >,

< ∆ >,< ∆ >,< ∆ >,< ∆ >,< ∆ >,< ∆ >,< ∆ >,< ∆ >,< ∆ >,< ∆ >,< ∆ >,

< ∆ >,< ∆ >,< ∆ >,< ∆ >,< ∆ >,< ∆ >,< ∆ >,< ∆ >,< ∆ >,< ∆ >,< ∆ >,< ∆ >,< ∆ >,< ∆ >,< ∆ >,<

∆ >,< ∆ >,< ∆ >,< ∆ >,<vldty>,,,,

<mondat>,<montm>"

.

.

.

.

.

.

.

.

.

"SPAN-a:PHASE1S,<monval>,< ∆ >,< ∆ >,< ∆ >,< ∆ >,

< ∆ >,< ∆ >,< ∆ >,< ∆ >,< ∆ >,< ∆ >,< ∆ >,< ∆ >,< ∆ >,< ∆ >,< ∆ >,

< ∆ >,< ∆ >,< ∆ >,< ∆ >,< ∆ >,< ∆ >,< ∆ >,< ∆ >,< ∆ >,< ∆ >,< ∆ >,

< ∆ >,< ∆ >,< ∆ >,< ∆ >,< ∆ >,< ∆ >,< ∆ >,< ∆ >,< ∆ >,< ∆ >,< ∆ >,

< ∆ >,< ∆ >,< ∆ >,< ∆ >,< ∆ >,< ∆ >,< ∆ >,< ∆ >,< ∆ >,< ∆ >,< ∆ >,

< ∆ >,< ∆ >,< ∆ >,< ∆ >,< ∆ >,< ∆ >,< ∆ >,< ∆ >,< ∆ >,< ∆ >,< ∆ >,

< ∆ >,< ∆ >,< ∆ >,< ∆ >,< ∆ >,< ∆ >,< ∆ >,< ∆ >,< ∆ >,< ∆ >,< ∆ >,

< ∆ >,< ∆ >,< ∆ >,< ∆ >,< ∆ >,< ∆ >,< ∆ >,< ∆ >,< ∆ >,< ∆ >,< ∆ >,

< ∆ >,< ∆ >,< ∆ >,< ∆ >,< ∆ >,< ∆ >,< ∆ >,< ∆ >,< ∆ >,< ∆ >,< ∆ >,< ∆ >,< ∆ >,< ∆ >,< ∆ >,<

∆ >,< ∆ >,< ∆ >,< ∆ >,<vldty>,,,,

<mondat>,<montm>"

;

242

TimeSource 3500

TL1 Reference

097-72050-01 Issue 7: August 2003

S S S S S S S S S S S S S S S S S S S S S S S S S S S

Retrieve Performance Monitoring (cont’d)

Note:

PHASE1S Data types:

S S

• One 15 minute bin from the last 24 hours of data as

900 seconds of data. To select a 15 minute bin, enter mondat and montm. Any mondat/montm combination outside of the past 24 hour window is denied. Any time increment may be entered. The system rounds the value to the nearest bin.

• Entered minutes of 1 to 15 correspond to the first

15 minute bin, 16 to 30 correspond to the second

15 minute bin, etc.

• The first monitor value is the first second of the 900 second window.

• The 900 seconds of data is broken into 9 groups of

100 seconds. For each group of 100 seconds, the first value is the absolute 1 second phase for that group. The absolute 1 second phase value is followed by 99 seconds of delta phase values.

2

TimeSource 3500

TL1 Reference

097-72050-01 Issue 7: August 2003

243

5

4

S S S S S S S S S S S S S S S S S S S S S S S

Retrieve Performance Monitoring (cont’d)

S S S S S S

Parameter

SPAN-a

PHASE1S

<monval>

< D>

<vldty>

MONDAT=a-b

MONTM=a-b a = A a = B

Value

First s of the

100 s data group. There are

9 groups of

100 s.

The difference

( D ) from the proceeding number

COMPL

NA a = 1 to 12 b = 1 to 31 a = 0 to 23 b = 0 to 59

Item Addressed

E1 span A input

E1 span B input

Phase 1S monitored type, which shows 900 s of phase values

Absolute monitored phase value

99 s of delta phase values which follow the absolute 1 s phase value

Data is valid

Data is not valid

Monitor date, month of the year

Monitor date, day of the month

Monitor time, hour of the day

Monitor time, minute of the hour

244

TimeSource 3500

TL1 Reference

097-72050-01 Issue 7: August 2003

S S S S S S S S S S S S S S S S S S S S S S S S

Retrieve Performance Monitoring (cont’d)

S S S S S

PHASE1S Response Example:

TS3500-2009 2000-05-25 11:01:58

M G COMPLD

"SPAN-A:PHASE1S,-325,0,0,0,0,0,0,0,0,0,0,0,0,0,0,

0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,1,0,0,0,0,0,0,0,0,0,0,0,0

,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,1,0,0,0,0,0,0,

0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,COMPL,,

,,2000-10-13,12-45-00"

"SPAN-A:PHASE1S,-323,0,0,0,0,0,0,0,1,0,0,0,0,0,

0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0

,0,0,0,0,0,0,0,COMPL,,,,2000-10-13,12-46-40"

"SPAN-A:PHASE1S,-321,0,0,0,0,0,0,0,0,0,0,0,0,0,

0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0

,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,1,0,0,0,0,0,0,0,0,

0,0,0,0,0,0,-1,0,0,0,0,0,0,0,

0,0,0,0,0,0,0,0,0,0,0,0,0,COMPL,,,,2000-10-13,12-48-20"

"SPAN-A:PHASE1S,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,

0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0

,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,

0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,NA,,,,2

000-10-13,12-50-00"

"SPAN-A:PHASE1S,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,

0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0

,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,

0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,NA,,,,2

000-10-13,12-51-40"

2

5

TimeSource 3500

TL1 Reference

097-72050-01 Issue 7: August 2003

245

4

S S S S S S S S S S S S S S S S S S S S S S S

Retrieve Performance Monitoring (cont’d)

S S S S S S

PHASE1S Response Example (cont’d):

"SPAN-A:PHASE1S,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,

0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0

,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,

0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,NA,,,,2

000-10-13,12-53-20"

"SPAN-A:PHASE1S,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,

0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0

,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,

0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,NA,,,,2

000-10-13,12-55-00"

"SPAN-A:PHASE1S,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,

0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0

,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,

0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,NA,,,,2

000-10-13,12-56-40"

"SPAN-A:PHASE1S,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,

0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0

,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,

0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,NA,,,,2

000-10-13,12-58-20"

/* LINK: 5001, CMD: RTRV-PM-EQPT::SPAN-A:C:: PHASE1S,,,,,

*/

;

246

TimeSource 3500

TL1 Reference

097-72050-01 Issue 7: August 2003

S S S S S S S S S S S S S S S S S S S S S S S S

Retrieve Performance Monitoring (cont’d)

S S S S S

PHASE1M Response Format:

<sid> <date> <time>

M <ctag>COMPLD

"SPAN-a:PHASE1M,<monval>,<monval>,

<monval>,<monval>,<monval>,<monval>,

.

.

.

.

.

.

.

.

.

<monval>,<monval>,<monval>,<monval>,

<vldty>,,,,<mondat>,<montm>"

/*LINK:<link>,CMD:<command>*/

;

2

TimeSource 3500

TL1 Reference

097-72050-01 Issue 7: August 2003

247

5

4

S S S S S S S S S S S S S S S S S S S S S S S S S S S

Retrieve Performance Monitoring (cont’d)

Note:

PHASE 1M Data types:

S S

• The TimeSource 3500 collects a full 7 days of 1 minute phase data.

• The 1 minute phase data is displayed in 1 hour groups.

Each request for 1 minute phase is synchronized to the hour.

• Any mondat/montm combination outside of the past 7 day window is denied. Any time increment may be entered. The system rounds the value to the nearest hour, i.e., the minute and second field of the montm is ignored.

• The first value (monval) is the oldest value in the range selected. For example, if montm = 8:45:32, the first monval will exceed time 8:00:00 followed by the value at 8:01:00, etc.

248

TimeSource 3500

TL1 Reference

097-72050-01 Issue 7: August 2003

S S S S S S S S S S S S S S S S S S S S S S S S

Retrieve Performance Monitoring (cont’d)

S S S S S

Parameter

SPAN-a

PHASE1M

<monval>

<vldty>

MONDAT=a-b

MONTM=a-b a = A a = B

Value Item Addressed

E1 span A input

E1 span B input

— Phase 1M monitored type, which shows 1 min phase data in 1 h groups of data

Absolute monitored phase value Oldest value in the range selected from the

<montm> value assigned in the command

COMPL

NA

Data is valid

Data is not valid a = 1 to 12 b = 1 to 31 a = 0 to 23 b = 0 to 59

Monitor date, month of the year

Monitor date, day of the month

Monitor time, hour of the day

Monitor time, minute of the hour

2

PHASE1M Response Example:

TS3500-2009 2000-05-25 11:01:58

M G COMPLD

"SPAN-A:PHASE1M,0,0,0,0,0,0,0,0,0,0,0,0,

0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0

,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,

0,0,COMPL,,,,,2000-05-25,100-00"

/*LINK:5002,CMD:RTRV-PM-EQPT::

SPAN-A:G::PHASE1M*/

;

TimeSource 3500

TL1 Reference

097-72050-01 Issue 7: August 2003

249

5

4

S S S S S S S S S S S S S S S S S S S S S S S S S S S S

Retrieve User Security

This command allows a system administrator to retrieve security parameters for a single user or for all users. The command format is:

S

RTRV-USER-SECU:[<tid>]:<uid>:<ctag>;

Parameter

<uid>

Value

(user name) Single user

ALL All users

Item Addressed

Response Format:

<sid> <date> <time>

M <ctag> COMPLD

"<aid>:,<uap>;,UOUT=<uout>"...

/*LINK:<link>,CMD:<command>*/

;

Parameter

<uap>

<uout>

Parameter Description

Access level (1 to 5)

(Displayed, but not implemented) Password for this account expires in this number (0 to 180) of days of inactivity; 0 indicates no expiration

250

TimeSource 3500

TL1 Reference

097-72050-01 Issue 7: August 2003

S S S S S S S S S S S S S S S S S S S S S S S S S S

Set Source Identifier

This command sets the name of the equipment sending the message. The command format is:

S S S

SET-SID:[<tid>]::<ctag>::<sid>;

Parameter

<sid>

Parameter Description

Source identifier – can be up to 20 uppercase or lowercase ASCII characters

Response Format:

<sid> <date> <time>

M <ctag> COMPLD

/*LINK:<link>,CMD:<command>*/

;

2

TimeSource 3500

TL1 Reference

097-72050-01 Issue 7: August 2003

251

5

S S S S S S S S S S S S S S S S S S S S S S S S S S S S S

4

252

TimeSource 3500

TL1 Reference

097-72050-01 Issue 7: August 2003

Troubleshooting

This chapter provides troubleshooting information using front-panel lamps and error messages. It also describes how to replace a card, return equipment, get technical and/or sales assistance, and obtain manual updates.

Chapter 5

S S S S S S S S S S S S S S S S S S S S S S S S S

Troubleshooting with Front Panel Items

S S

All front panel items are shown in Figure 39. The items are described in Table K. Use Table K to troubleshoot the system based on the front-panel lamps.

S S

Figure 39. Controls and Indicators

Alarms

MIN

5

254

Status

GPS

Status

SYS

Alarms

CRIT

Alarms

MAJ

ACO

Lamp

ACO

Pushbutton

TimeSource 3500

Troubleshooting

097-72050-01 Issue 7: August 2003

S S S S S S S S S S S S S S S S S S S S S S S S S S S S S

Table K. Front Panel Items

Name

Status GPS

State

Off

Description

System is not powered.

Action

If in warm-up, none required.If there is no power, apply power.

None required.

Status SYS

Alarms CRIT

Alarms MAJ

Green GPS is successfully tracking satellites, or is in warm-up.

Yellow

Red

Off

Red

Off

Red

A GPS event has occurred.

A GPS event, which has existed per the user alarm setting, has escalated to a minor alarm.

Off System is in warm-up mode or is not powered.

Green The output signal is PRS.

Red The system has been in holdover per the user alarm setting, or there is a hardware fault.

There is no critical alarm.

A critical alarm has occurred because of a hardware failure.

There is no major alarm.

The system has been in holdover per the user alarm setting.

None required.

Refer to Table L to determine which type and combination of antenna alarms exist, and the recommended action.

If in warm-up, none required. If there is no power, apply power.

None required.

Refer to Table L to determine which type and combination of alarms exist, and the recommended action.

None required.

Replace the plug-in card, using

Procedure J.

None required.

Refer to Table L to determine which type and combination of antenna alarms exist, and the recommended action.

2

3

5

TimeSource 3500

Troubleshooting

097-72050-01 Issue 7: August 2003

255

5

S S S S S S S S S S S S S S S S S S S S S S S S S S S S S

Table K. Front Panel Items (cont’d)

Name State

Alarms MIN Off

ACO

(Lamp)

ACO

(Pushbutton)

Yellow A minor alarm has occurred because Battery A or B has failed.

Off

Description

There is no minor alarm.

A minor alarm has occurred because a software download is required.

A minor alarm has occurred because an event (GPS error, temperature error, or span input problem) has escalated to a minor alarm.

A minor alarm has occurred because the antenna failed.

Action

None required.

Troubleshoot and repair the specified – 48 V battery input.

Refer to Table L to determine which software needs to be downloaded and the recommended action.

Refer to Table L to determine which event occurred and the recommended action.

The alarm cutoff function has not been activated.

Refer to Table L to determine whether the minor alarm is due to antenna failure and the recommended action.

None required. Press the ACO pushbutton to silence all audible alarms.

None required.

Green The alarm cutoff function has been activated.

— Silences all audible alarms when pressed.

None required.

256

TimeSource 3500

Troubleshooting

097-72050-01 Issue 7: August 2003

S S S S S S S S S S S S S S S S S S S S S S S S S

Troubleshooting with Error Messages

S S

Use the information in Table L to troubleshoot the system based on the condition description (conddescr) parameter in a message.

S S

Note:

If only the character “C” is displayed on the terminal every few seconds, the TimeSource 3500 system has restarted with corrupt software. Download and install the system software again, using the procedure in the Software Release Document that came with the software.

2

Table L. Message Troubleshooting

Message

HARDWARE FAULT

HOLDOVER

BATTERY x FAIL

BT3 WARMUP

Meaning Action

CRITICAL ALARMS

A failure has been detected on the shelf hardware.

Replace the plug-in card.

MAJOR ALARMS

All inputs (GPS signal and span inputs) are lost or unacceptable, and the system is now using the internal oscillator.

MINOR ALARMS

Troubleshoot the GPS and SPAN x error messages.

The specified – 48 V battery input has failed.

The system is in a power-up state when it should not be.

Troubleshoot, and repair, the specified

– 48 V battery input.

Perform the same action as shown in

GPS ERROR message.

3

5

TimeSource 3500

Troubleshooting

097-72050-01 Issue 7: August 2003

257

5

S S S S S S S S S S S S S S S S S S S S S S S S S S S S S

Table L. Message Troubleshooting (cont’d)

Message

DEVICE

DOWNLOAD

REQUIRED

GPS ERROR

GPS DOWNLOAD

REQUIRED

Meaning

The hardware device software is corrupt or missing.

The GPS receiver is reporting an error.

The GPS software is corrupt or missing.

Action

Download and install the appropriate hardware device (DEV) software, using the procedure in the Software Release

Document that came with the software.

If the installation includes a roof antenna, or if the message is accompanied by the HIGH CURRENT

FAULT or LOW CURRENT FAULT message, follow the recommended action for the HIGH CURRENT FAULT or LOW CURRENT FAULT message.

If the installation includes a window or wall antenna:

1. Note the satellite tracking success rate reported by the RTRV-GPS-

STAT command.

2. If the success rate is better than

40%, follow the recommended action for the HIGH CURRENT

FAULT or LOW CURRENT FAULT message.

3. If the success rate is less than 40%, check that the latitude, longitude, and altitude data (position data) are correct.

4. If the position data are correct and the error repeats, move the antenna to a location with an improved view of the sky.

5. If the error repeats, follow the recommended action for the HIGH

CURRENT FAULT or LOW

CURRENT FAULT message.

Download, and install, the GPS receiver (GPS) software, using the procedure in the Software Release

Document that came with the software.

258

TimeSource 3500

Troubleshooting

097-72050-01 Issue 7: August 2003

S S S S S S S S S S S S S S S S S S S S S S S S S S S S S

Table L. Message Troubleshooting (cont’d)

Message

HIGH CURRENT

FAULT

LOW CURRENT

FAULT

Meaning

Current to antenna is outside specification.

Action

If not accompanied by the GPS ERROR alarm, none required.

If accompanied by the GPS ERROR alarm:

1. Check the cable connections between the TimeSource 3500

Shelf and the antenna.

2. If the error repeats, remove the antenna cable from the rear of the shelf, and measure the dc voltage from the connector center pin to the connector housing on the shelf

TNC antenna connector.

3. If the voltage is not 24 V dc ±2 V dc, replace the TimeSource 3500 card, using Procedure J.

4. If the voltage is 24 V dc ±2 V dc, measure the current between the connector center pin and the connector housing on the shelf

TNC antenna connector.

5. If the current is less than 110 mA or more than 150 mA, replace the

TimeSource 3500 card, using

Procedure J. If not (nominal current is 125 mA), re-connect the antenna cable to the rear of the shelf.

6. Remove the antenna cable from the antenna, and measure dc voltage and current from the connector center pin to the connector housing on the cable connector.

7. If the readings are 24 V dc and

125 mA, replace the antenna. If not, verify the cable path. Replace cables, lightning suppressor, or IF converter as necessary.

8. If the error repeats, replace the antenna.

TimeSource 3500

Troubleshooting

097-72050-01 Issue 7: August 2003

259

2

3

5

5

S S S S S S S S S S S S S S S S S S S S S S S S S S S S S

Table L. Message Troubleshooting (cont’d)

Message

SPAN x AIS

SPAN x ERROR

SPAN x LOSS OF

SIGNAL

TEMPERATURE

ERROR

TS3500

DOWNLOAD

REQUIRED

BT3 WARMUP

260

Meaning

An AIS has been received on the specified input span.

An error has been detected on the specified input span.

The signal on the specified input span has been lost.

A temperature error has been detected on the internal oscillator.

The system software is corrupt or missing.

EVENTS

The system is in a power-up state.

Action

Troubleshoot the specified input span signal (check the source).

Troubleshoot the specified input span signal (include checks for signal frequency and jitter).

Troubleshoot the specified input span signal (check the cable, connections, source).

If this occurs momentarily during power-up, none required.

If this does not occur during power-up:

1. Check that the ambient air temperature is within the

TimeSource 3500 environmental specifications. If not, correct the ambient temperature with heating or air conditioning.

2. If the ambient air temperature is within the TimeSource 3500 environmental specifications, replace the plug-in card.

Download and install the system

(TimeSource 3500) software again, using the procedure in the Software

Release Document that came with the software.

Wait for the system to power up

(20 min to several hours, depending on antenna placement and view of the sky).

TimeSource 3500

Troubleshooting

097-72050-01 Issue 7: August 2003

S S S S S S S S S S S S S S S S S S S S S S S S S S S S S

Table L. Message Troubleshooting (cont’d)

Message Meaning Action

COM-x USER

TIMEOUT LOGOFF

DISCONNECTED

USER LOGOFF

HOLDOVER

CRITICAL ACO

EVENT

The user was auto logged off.

If COM-x is the port this message was received on, retry logging in. If not, none required.

A user was logged off by the system administrator.

None required.

None required.

All inputs (GPS signal, span inputs) are lost or unacceptable. The system is using the internal oscillator.

The ACO pushbutton has been pressed to deactivate a critical audible alarm.

None required.

DOWNLOAD FAILED The software download has failed.

DOWNLOAD IN

PROGRESS

Software is being downloaded.

DOWNLOAD

SUCCESSFUL

GPS ERROR

The software has been downloaded successfully.

The GPS receiver is reporting an error.

Retry the software download.

Wait until the download has been completed.

None required.

None required.

MAJOR ACO EVENT The ACO pushbutton has been pressed to deactivate a major audible alarm.

MINOR ACO EVENT The ACO pushbutton has been pressed to deactivate a minor audible alarm.

POWER UP RESTART The system processor has just started up.

None required.

None required.

None required.

2

3

5

TimeSource 3500

Troubleshooting

097-72050-01 Issue 7: August 2003

261

5

S S S S S S S S S S S S S S S S S S S S S S S S S S S S S

Table L. Message Troubleshooting (cont’d)

Message

SETTLING PERIOD

SOFTWARE

DOWNLOADING

ON LINK

SPAN x AIS

SPAN x ERROR

SPAN x LOSS OF

SIGNAL

SPAN x SSM

QUALITY DUS

SPAN x SSM

QUALITY ST2

SPAN x SSM

QUALITY ST3E

SPAN x SSM

QUALITY ST3

SPAN x SSM

QUALITY ST4

Meaning

The system is between the power-up state and steadystate operation, and signals may be degraded.

Software is being downloaded at specified communication port.

An AIS has been received on the specified input span.

An error has been detected on the specified input span.

The signal on the specified span input has been lost.

Do not use for synchronization.

The signal on the specified span input has degraded to an SSM quality level of ST2.

The signal on the specified span input has degraded to an SSM quality level of ST3E.

The signal on the specified span input has degraded to an SSM quality level of ST3.

The signal on the specified span input has degraded to an SSM quality level of ST4.

None required.

None required.

Action

Troubleshoot the specified input span

(check the source).

Troubleshoot the specified input span

(check the source).

Troubleshoot the specified input span

(check the source).

Troubleshoot the specified input span

(check the source).

Troubleshoot the specified input span

(check the source).

Troubleshoot the specified input span

(check the source).

Troubleshoot the specified input span

(check the source).

Troubleshoot the specified input span

(check the source).

262

TimeSource 3500

Troubleshooting

097-72050-01 Issue 7: August 2003

S S S S S S S S S S S S S S S S S S S S S S S S S S S S S

Table L. Message Troubleshooting (cont’d)

Message

SPAN x SSM

QUALITY STU

TEMPERATURE

ERROR

Meaning

Do not use for synchronization. The level of synchronization traceability is unknown.

A temperature error has been detected on the internal oscillator.

Action

Troubleshoot the specified input span

(check the source).

Wait until this escalates to a minor alarm, or check that the ambient air temperature is within the

TimeSource 3500 environmental specifications. If not, correct the ambient temperature with heating or air conditioning.

2

3

TimeSource 3500

Troubleshooting

097-72050-01 Issue 7: August 2003

263

5

5

S S S S S S S S S S S S S S S S S S S S S S S S S S S

Card Replacement

To replace the plug-in card, follow the steps in Procedure J, and refer to Figure 40.

S S

Procedure J. Card Replacement

Step Procedure

1 Put on an ESD wrist strap.

2 Plug the ESD wrist strap into the ESD jack on of the front panel of the shelf.

On the Faulty Card

3 Loosen the two retaining screws that secure the plug-in card in the shelf.

4 Pull out on the two latching levers to disconnect the card from the shelf connectors.

5 Pull the card completely out of the shelf.

On the Replacement Card

6 Pull out the latching levers at each end of the front panel of the card so that the levers are pointing directly out from the front panel of the card.

7 Insert the new card into the tracks at each side of the shelf, and slide the card into the shelf until the latching levers begin to move in.

8 Push the latching levers flat against the front panel of the card to complete the card insertion.

9 Tighten the knurled screw above each latching lever to secure the card in the shelf.

10 Unplug and remove the grounding wrist strap.

11 Reconfigure the system per application requirements.

End of Procedure

264

TimeSource 3500

Troubleshooting

097-72050-01 Issue 7: August 2003

S S S S S S S S S S S S S S S S S S S S S S S S S S S S S

Figure 40. Front of Shelf

ESD Jack

Retaining Screw Retaining Screw

2

Latching Lever Latching Lever

3

TimeSource 3500

Troubleshooting

097-72050-01 Issue 7: August 2003

265

5

5

266

S S S S S S S S S S S S S S S S S S S S S S S S S S S

Repair and Return

S

When returning defective equipment for factory repair, obtain the following information prior to calling Symmetricom:

S

• A complete description of the trouble (alarms, equipment behavior, etc.), part number, serial number, issue/revision level, and warranty expiration date.

• If the warranty has expired, a purchase order with “bill to” information.

• A customer field technical contact including address, phone number and FAX number.

• Return shipping information.

To return defective or damaged equipment, use Procedure K.

TimeSource 3500

Troubleshooting

097-72050-01 Issue 7: August 2003

S S S S S S S S S S S S S S S S S S S S S S S S S S S S S

Procedure K. Equipment Return

Step Procedure

1 Call your local Symmetricom distributor or Symmetricom’s Inside Sales (refer to the

Sales subsection), and obtain a Return Material Authorization (RMA) number and shipping address.

Note: Retain the RMA number for future reference. The RMA number is used by

Symmetricom for internal tracking of the unit. Reference the RMA number in all communications with Symmetricom regarding the unit.

2 Pack the defective equipment, including a list containing all the information obtained above, in the original packing material. If the original packing material is not available, inform Symmetricom, and the appropriate shipping material will be provided.

Note: Equipment must be returned in the original packaging, or approved replacement packaging for the warranty to be honored.

3 Mark the RMA number and the equipment serial number on the outside of the shipping carton.

4 Ship the equipment prepaid and insured to one of the addresses below, as directed by the Customer Assistance Center:

Symmetricom

Attn: Customer Service

2300 Orchard Parkway

San Jose, CA 95131 or

Symmetricom

Attn: Repair and Return

Montana Industrial Park

Street B Lot 52

Aguadilla, Puerto Rico 00603

Note: Repaired equipment is typically shipped within 30 days of receipt by

Symmetricom, or per contract terms. Shipping costs to Symmetricom are paid by the customer; shipping costs back to the customer are paid by Symmetricom.

End of Procedure

TimeSource 3500

Troubleshooting

097-72050-01 Issue 7: August 2003

267

2

3

5

5

268

S S S S S S S S S S S S S S S S S S S

Technical Assistance

S S

For technical assistance, contact the following:

S S S S S S S S

Symmetricom, Inc.

2300 Orchard Parkway

San Jose, CA 95131-1017

U.S.A. Call Center:

1-888-367-7966 (from inside U.S.A. only – toll-free)

1-408-428-7907

Fax: 1-408-428-7998

Europe, Middle East, and Africa (EMEA) Call Center:

+44 (0) 1189 699 799

Fax: +44 (0) 1189 277 520

E-mail: [email protected]

Internet: http://www.symmetricom.com

TimeSource 3500

Troubleshooting

097-72050-01 Issue 7: August 2003

S S S

Sales

S S S S S S S S S S S S S S S S S S S S S S S S S S

For sales assistance, contact the following:

Symmetricom, Inc.

2300 Orchard Parkway

San Jose, CA 95131-1017

U.S.A. Call Center:

1-888-367-7966 (from inside U.S.A. only – toll-free)

1-408-428-7907

Europe, Middle East, and Africa (EMEA) Call Center:

+44 (0) 1189 699 799

Fax: 408-428-7998

E-mail: [email protected]

Internet: http://www.symmetricom.com

2

3

TimeSource 3500

Troubleshooting

097-72050-01 Issue 7: August 2003

269

5

5

270

S S S S S S S S S S S S S S S S S S S S S S S S S

Manual Updates

S S

From time to time, this manual may be updated. The updated version of the manual will be available for downloading in electronic form via the Internet. After downloading, the manual can be viewed on a computer or printed out.

S S

Manual updates are available at: http://www.symmetricom.com/support/login/login.php

Note: When going to the preceding Web address, it is necessary to register if you are a new user. If you are a currently registered user, enter your user name and password, and log in.

TimeSource 3500

Troubleshooting

097-72050-01 Issue 7: August 2003

Specifications

This chapter provides equipment specifications.

Chapter 6

6

S S S S S S S S S

Antennas

S S S S S S S S S S S S S S S S S S S S

Roof Antenna

Type: Active volute antenna, right-hand circular polarized, with proprietary IF interface

Maximum 1,000 feet from antenna to shelf Cable Length:

Dimensions:

Height:

Diameter:

Weight:

Operating Temperature:

Storage Temperature:

Operating Humidity:

11 in.

4.3 in.

9 oz

– 30 °C to +80 °C

– 40 °C to +80 °C

0% to 100% relative humidity

Mechanical Window Antenna

Type: Patch antenna

Cable Length: Maximum 1000 ft from antenna to shelf

Dimensions: (antenna, including mechanical mounting device)

Height: 16 in.

Width:

Depth:

2.2 in.

1.3 in.

Weight: 18 oz

272

TimeSource 3500

Specifications

097-72050-01 Issue 7: August 2003

S S S S S S S S S S S S S S S S S S S S S S S S S S S S S

Antennas (cont’d)

Wall Antenna

Type: Patch antenna

Cable Length: Maximum 1000 ft from antenna to shelf

Dimensions: (not including mounting and peripheral equipment)

Height: 0.5 in. (12.5 mm)

Width:

Depth:

1.5 in. (37 mm)

1.8 in. (46 mm)

Weight: 1.1 oz (35 g)

2

Self-Adhesive Window Antenna

Type: Patch antenna

Maximum 1000 ft from antenna to shelf Cable Length:

Dimensions:

Length:

Width:

Height:

4 in.

3 in.

1.5 in.

Weight: 5.3 oz

3

TimeSource 3500

Specifications

097-72050-01 Issue 7: August 2003

273

6

S S S S S S S S S S S S S S

Communication Ports

S S S S S S S S S S S S S S S

Port 1

Connector Type:

Connector Label:

Connector Location:

Electrical Interface:

Pin that transmits data:

Pin that receives data:

Baud Rate:

Data Bits:

Parity Bit:

Stop Bits:

Flow Control:

25-pin, female D connector

COM1

Rear panel

RS-232 (DTE equivalent)

2

8

1

2

None

Even

Odd

3

1200 b/s

2400 b/s

4800 b/s

9600 b/s (factory default)

19.2 kb/s

38.4 kb/s

57.6 kb/s

115 kb/s

None

Software (XON/XOFF)

Hardware (CTS/RTS)

274

TimeSource 3500

Specifications

097-72050-01 Issue 7: August 2003

S S S S S S S S S S S S S S S S S S S S S S S S S S S S S

Communication Ports (cont’d)

Port 2

Connector Type:

Connector Label:

Connector Location:

Electrical Interface:

Pin that transmits data:

Pin that receives data:

Baud Rate:

Data Bits:

Parity Bit:

Stop Bits:

Flow Control:

RJ-45

COM2

Rear panel

RS-232 (DCE equivalent)

2

8

1

2

None

Even

Odd

3

1200 b/s

2400 b/s

4800 b/s

9600 b/s (factory default)

19.2 kb/s

38.4 kb/s

57.6 kb/s

115 kb/s

None

Software (XON/XOFF)

Hardware (CTS/RTS)

2

3

TimeSource 3500

Specifications

097-72050-01 Issue 7: August 2003

275

6

S S S S S S S S S S S S S S S S S S

Communication Ports (cont’d)

S S S S S S S S S S S

Craft Port

Connector Type:

Connector Label:

Connector Location:

Electrical Interface:

Pin that transmits data:

Pin that receives data:

Baud Rate:

Data Bits:

Parity Bit:

Stop Bits:

Flow Control:

RJ-45

Craft

Front panel

RS-232 (DTE equivalent)

2

8

1

2

None

Even

Odd

3

1200 b/s

2400 b/s

4800 b/s

9600 b/s (factory default)

19.2 kb/s

38.4 kb/s

57.6 kb/s

115 kb/s

None

276

TimeSource 3500

Specifications

097-72050-01 Issue 7: August 2003

S S S S S S S S S S S S S S S S S S S S S S S S S S S S S

Ethernet Port

Connector Type:

Connector Label:

Connector Location:

Electrical Interface:

Data Rate:

Protocol:

Setup Language:

RJ-45 (10Base-T)

Ethernet

Rear panel

10Base-T Ethernet

10Mb/s

TCP/IP (interface)

TL1 (application layer)

2

3

TimeSource 3500

Specifications

097-72050-01 Issue 7: August 2003

277

6

S S S S S S S S S S S S S S

Time of Day Outputs

S S S S S S S S S S S S S S S

Network Time Protocol (NTP),

Type 4, Format 2 Driver Format

Connector Type: RJ-45

Connector Label:

Connector Location:

Electrical Interface:

TOD

Rear panel

RS-485

Baud Rate:

Data Bits:

Parity Bit:

Stop Bit:

Data Format:

9600 b/s

8

None

1

See Figure 41

Figure 41. NTP Type 4 Data Format

1 2 3 4 5 6

Example:

1 Alarm field: blank space = receiver has satellite availability; ? = no satellite available

2 Year (2000 in this example)

3 Day of year (the 225th day of the year in this example)

4 Hours:minutes:seconds:milliseconds

5 Leap second: blank space = no leap second; L = upcoming leap second

6 Daylight savings time indicator: S = standard time; D = daylight savings time

278

TimeSource 3500

Specifications

097-72050-01 Issue 7: August 2003

S S S S S S S S S S S S S S S S S S S S S S S S S S S S S

Time of Day Outputs (cont’d)

Cisco Systems

Connector Type:

Connector Label:

Connector Location:

Electrical Interface:

Baud Rate:

Bit Configuration:

Data Format:

RJ-45

TOD

Rear panel

RS-485

9600 b/s

8 data bits, No parity, 1 stop bit

See Figure 42

2

Figure 42. Cisco Systems Data Format

Example:

1 2 3 4 5 6 7 8 9 10 11 12 13 14

3

1 Satellite availability: * = valid, ! = not valid

2 Revision

3 Modified Julian date (number of days past midnight, Nov 17, 1858)

4 Year/month/day

5 Hours:minutes:seconds

6 Indicator of time zone offset (+, –, or 0)

7 Time zone offset

8 Leap second indicator

9 Latitude

10 Longitude

11 Altitude above mean sea level in meters

12 Alarm severity: EV = event, MN = minor, MJ = major, CL = critical

13 Alarm source

14 Alarm cause: holdover, BT3 warm-up, or hardware fault

TimeSource 3500

Specifications

097-72050-01 Issue 7: August 2003

279

6

S S S S S S S S S S S S S S S S S

Time of Day Outputs (cont’d)

S S S S S S S S S S S S

IRIG-B TOD Outputs

(990-72050-05 System Only)

Connector Type: BNC

Connector Labels: OUT1

OUT2

Connector Location: OPTION I/O wire-wrap pins on rear panel and output module

600 Ω Impedance:

Number of Outputs:

Type of Output:

Amplitude:

2

Amplitude modulated

6 V peak-to-peak maximum terminated with

600 Ω

Time Format:

Binary Coded Decimal (BCD):Seconds:

Non BCD:

Minutes:

Hours:

Days:

0 – 59

0 – 59

0 – 23

0 – 364

Years: 0 – 99

Seconds of day:0 – 86399

280

TimeSource 3500

Specifications

097-72050-01 Issue 7: August 2003

S S S S S S S S S S S S S S S S S S S S S S S S S S S S S

T1 Inputs

Connector Type:

Connector Label (2 sets):

Connector Location:

Impedance:

Bit Rate:

Format:

Line Code:

SSM State:

Amplitude:

Framing:

Wire-wrap pins

T

R

S

Rear panel

100 Ω ±5% balanced

1.544 Mb/s

DS1

Alternate mark inversion (AMI) with or without

B8ZS

Enable

Disable

0 to – 26 dB DSX

ESF

D4

2

3

TimeSource 3500

Specifications

097-72050-01 Issue 7: August 2003

281

6

S S S S S S S S S S S S

1 PPS Output

Connector Type:

Connector Label:

Connector Location:

Impedance:

Frequency:

Amplitude:

Time Accuracy:

S S

GPS Holdover Time Error:

Format:

Rise Time:

S S S S S S S S S S S S S S S

BNC

TTL PPS

Rear panel

50 Ω

1 pps

Transistor-transistor logic (TTL) levels

100 ns with respect to Universal

Coordinated

Time (UTC) when locked to GPS signal

3 µs for 72 h (0 °C to +50 °C ± 5 °C) after one week of steady-state operation

Logic low with logic high pulse of 1 µs

Less than 20 ns

282

TimeSource 3500

Specifications

097-72050-01 Issue 7: August 2003

S S S S S S S S S S S S S S S S S S S S S S S S S S S S S

T1 Outputs

Standard

Connector Type:

Connector Label:

Connector Location:

Impedance:

Bit Rate:

Frequency Accuracy:

GPS Holdover Stability:

Format:

Line Code:

Amplitude:

Framing:

Output During Alarms:

Wire-wrap pins

T1 OUT A (T, R, S)

T1 OUT B (T, R, S)

Rear panel

100 Ω

1.544 Mb/s

1 x 10 – 12

1 x 10 – 11

for 72 h (0 °C to +50 °C ±

5 °C) after one week of steady-state operation

1 x 10 – 10 for 30 days after one week of steady-state operation

DS1, framed all 1s

Alternate mark inversion (AMI)

2.4 V to 3.6 V terminated with 100 Ω

ESF

D4

AIS

Squelch

SSM

2

3

TimeSource 3500

Specifications

097-72050-01 Issue 7: August 2003

283

6

S S S S S S S S S S S S S S

T1 Outputs (cont’d)

S S S S S S S S S S S S S S S

Additional T1 Outputs

(990-72050-02 System Only)

Connector Type: Wire-wrap pins

Connector Label:

Connector Location:

Impedance:

Bit Rate:

1 (T, R, S)

2 (T, R, S)

3 (T, R, S)

4 (T, R, S)

5 (T, R, S)

6 (T, R, S)

7 (T, R, S)

8 (T, R, S)

OPTION I/O wire-wrap pins on rear panel

100 Ω

1.544 Mb/s

Frequency Accuracy:

GPS Holdover Stability:

Format:

Line Code:

Amplitude:

1 x 10 – 12

1 x 10 – 11

for 72 h (0 °C to +50 °C ±

5 °C) after one week of steady-state operation

1 x 10 – 10

for 30 days after one week of steady-state operation

DS1, framed all 1s

Alternate mark inversion (AMI)

2.4 V to 3.6 V terminated with 100 Ω

284

TimeSource 3500

Specifications

097-72050-01 Issue 7: August 2003

S S S S S S S S S S S S S S S S S S S S S S S S S S S S S

T1 Outputs (cont’d)

Additional T1 Outputs (cont’d)

(990-72050-02 System Only)

Framing: ESF

D4

Output During Alarms: AIS

Squelch

SSM

2

3

TimeSource 3500

Specifications

097-72050-01 Issue 7: August 2003

285

6

S S S S S S S S S S S S S S

Mixed E1/T1 Outputs

S S S S S S S S S S S S S S S

(990-72050-06 System Only)

Note: For E1/T1 commonality, refer to the E1/T1 Common specifications. For

E1, refer to the E1 Outputs specifications. For T1, refer to the T1 Outputs specifications.

E1/T1 Common

Connector Type:

Connector Label:

Connector Location:

Frequency Accuracy:

Output During Alarms:

E1 Outputs

Impedance:

Bit Rate:

Format:

Line Code:

Amplitude:

Framing:

Wire-wrap

T, R, S

OPTION I/O wire-wrap pins on rear panel

1 x 10

–12

AIS, Squelch, SSM

120 Ω balanced or 75 Ω unbalanced

2.048 Mb/s

Framed all 1s

HDB3

3.0 V nominal terminated with 120 Ω balanced

CAS, CAS4, CCS, CCS4

286

TimeSource 3500

Specifications

097-72050-01 Issue 7: August 2003

S S S S S S S S S S S S S S S S S S S S S S S S S S S S S

Mixed E1/T1 Outputs (Optional) (cont’d)

E1 Outputs (cont’d)

GPS Holdover Stability: 1 x 10

-11

for 72 h (0 °C to +50 °C ± 5 °C) after one week of steady-state operation

1 x 10 -10 for 30 days after one week of steady-state operation

2

T1 Outputs

Impedance:

Bit Rate:

Format:

Line Code:

Amplitude:

Framing:

GPS Holdover Stability:

(after one week of steady-state operation)

100 Ω

1.544 Mb/s

DS1, framed all 1s

Alternate mark inversion (AMI)

2.4 V to 3.6 V terminated with 100 Ω

ESF, D4

1 x 10 -10 per day

3.2 x 10

-11

per day with span input meeting

ANSI T1.101 network specification

99% probability (rubidium)

1 x 10 -11 per day over a 10 °C range between 0 °C and + 50 °C with an

ST2E remote oscillator input (quartz)

3

TimeSource 3500

Specifications

097-72050-01 Issue 7: August 2003

287

6

S S S S S S S S S S S S S S S S S S S S S S S S S

Mixed T1/CCK Outputs

(990-72050-07 System Only)

Note: For T1/CCK commonality, refer to the T1/CCK Common specifications. For T1, refer to the T1 Outputs specifications.

For CCK, refer to the CCK Outputs specifications.

S S S S

T1/CCK Common

Connector Type:

Connector Label:

Connector Location:

Wire-wrap

T, R, S

OPTION I/O wire-wrap pins on rear panel

288

T1 Outputs

Impedance:

Bit Rate:

Format:

Line Code:

Amplitude:

Framing:

GPS Holdover Stability:

(after one week of steady-state operation)

100 Ω

1.544 Mb/s

DS1, framed all 1s

Alternate mark inversion (AMI)

2.4 V to 3.6 V terminated with 100 Ω

ESF, D4

1 x 10 -10 per day

3.2 x 10

-11

per day with span input meeting

ANSI T1.101 network specification

99% probability (rubidium)

1 x 10 -11 per day over a 10 °C range between 0 °C and + 50 °C with an

ST2E remote oscillator input (quartz)

TimeSource 3500

Specifications

097-72050-01 Issue 7: August 2003

S S S S S S S S S S S S S S S S S S S S S S S S S S S S S

Mixed T1/CCK Outputs

(990-72050-07 System Only) (cont’d)

CCK Outputs

Impedance:

Bit Rate:

Waveform:

Wave Shape:

Duty Cycle:

135 Ω balanced

64 kb/s

2.7 V to 5.5 peak, 3 V nominal; bipolar

RTZ; all ones with BPV every eight pulse

Rectangular, rise time <500 ns, pulse width

9.8 µs ±5%, pulse interval 15.6 µs ±5%

62.5%

2

3

TimeSource 3500

Specifications

097-72050-01 Issue 7: August 2003

289

6

S S S

Connector Location:

Impedance:

Bit Rate:

Waveform:

Wave Shape:

Duty Cycle:

S S S S S S S S S S S S S S S S S S S S S S S S S

Composite Clock Outputs

(990-72050-03 System Only)

Connector Type: Wire-wrap pins

Connector Label: 1 (T, R, S)

2 (T, R, S)

3 (T, R, S)

4 (T, R, S)

5 (T, R, S)

6 (T, R, S)

7 (T, R, S)

8 (T, R, S)

OPTION I/O wire-wrap pins on rear panel

135 Ω balanced

64 kb/s

2.7 V to 3.5 peak, 3 V nominal; bipolar

RTZ; all ones with BPV every eight pulse

Rectangular, rise time <500 ns, pulse width

9.8 µs ±5%, pulse interval 15.6 µs ±5%

62.5%

S

290

TimeSource 3500

Specifications

097-72050-01 Issue 7: August 2003

S S S S S S S S S S S S S S S S S S S S S S S S S S S S S

10 MHz Output

Connector Type:

Connector Label:

Connector Location:

Impedance:

Frequency:

Stability:

Phase Noise:

Harmonic Distortion:

Spurious Distortion:

Format:

Amplitude:

BNC

10 MHz

Rear panel

50 Ω

10 MHz

5 x 10 – 12 Root Allen Variance (RAV) at 10 s

–110 dBc @ 10 Hz

–135 dBc @ 100 Hz

–140 dBc @ 1 kHz

–145 dBc @ 10 kHz

–40 dBc

–70 dBc

Sine wave

1 V peak-to-peak minimum, 50 Ω termination

3.7 V peak-to-peak typical, 50 Ω termination

2

3

TimeSource 3500

Specifications

097-72050-01 Issue 7: August 2003

291

6

S S S S S S S S S S

Office Alarms

S S S S S S S S S S S S S S S S S S S

Rear Panel Contacts

Connection:

Type:

Contact Rating:

Severity:

State:

Style:

Wire-wrap pins

Dry contact

1 A @ 30 V dc

0.5 A @ 60 V dc

0.5 A @ 125 V ac

Critical

Major

Minor

Normally open and normally closed

Audible and visible

Front Panel Lamps

Label:

Type:

Front Panel Control

Label:

Type:

Function:

Alarms (CRIT, MAJ, MIN, ACO)

Status (GPS, SYS)

Light emitting diode

ACO

Push-button switch

Alarm cutoff (deactivates audible office alarms)

292

TimeSource 3500

Specifications

097-72050-01 Issue 7: August 2003

S S S S S S S S S S S S S S S S S S S S S S S S S S S S S

Simple Network Time Protocol

Protocol Type: SNTP (Simple Network Time Protocol) compliant with RFC-1769 for unicast applications

SNTP Accuracy:

SNTP Alarm Indications:

SNTP timestamp derived from UTC time via integrated GPS receiver within

–300 microseconds

1. SNTP packet will indicate Stratum 2 in NTP packet header if GPS is out of lock.

Password Activated:

2. The “ref id” field changes from GPS to at Stratum 1 to the IP address at Stratum 2 to signify that the reference is the TimeSource clock itself.

3. SNTP packet will indicate “clock not synchronized” in LI field as a “3” value after user defined alarm integration time.

Contact factory

2

3

TimeSource 3500

Specifications

097-72050-01 Issue 7: August 2003

293

6

S S S S S S S S S

Power

S

Connector Type:

S S

Connector Labels:

Voltage:

Current:

Steady-State Power

Recommended Fuse for Battery Feed:

S S S S S S S S S S S S S S S S S

Terminal block

TB1

TB2

–40 V dc to –72 V dc (A & B feed)

750 mA maximum

30 W maximum

3 A

Shelf Mechanical

Rack Mounting:

Mounting Positions:

Width:

Height:

Depth:

Weight:

NEBS 19 in. rack

NEBS 23 in. rack

Flush

5 in. offset

19 in.

3.5 in. maximum (2 rack mounting units)

12 in. maximum

13 lb.

294

TimeSource 3500

Specifications

097-72050-01 Issue 7: August 2003

S S S S S S S S S S S S S S S S S S S S S S S S S S S S S

Shelf Environmental

Operating Temperature:

Operating Humidity:

Electromagnetic:

Safety

0 °C to +50 °C

Up to 95% non condensing

FCC Part 15, Sub-Part B, Class A

UL compliant

NEBS compliant

2

3

TimeSource 3500

Specifications

097-72050-01 Issue 7: August 2003

295

6

S S S S S S S S S S S S S S S S S S S S S S S S S S S S S

This page intentionally left blank.

296

TimeSource 3500

Specifications

097-72050-01 Issue 7: August 2003

Index

S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S

"Bridging" mode 40

"BT3 Warmup" event 39

"Holdover" event 40–41

"Holdover" event/alarm 41

"Holdover" mode 40

"Power Up Restart" event 39

"Settling Period" event 39

Symbols

1 PPS Output specifications 282

10 MHz Output specifications 291

A

Activate User 131, 174, 177

Alarm All, Retrieve 175, 208

Alarm Cutoff All, Operate 175, 207

Alarm Equipment, Retrieve 175, 209–210

Alarm Programmability 38

Algorithm, BesTime 28, 33

Antenna types 22

Antenna, mechanical 22

Antenna, mechanical window 25, 30

Antenna, roof 22, 24, 30

Antenna, self-adhesive window 22, 26, 30

Antenna, wall 22, 27, 30

Antennas, GPS 21

Application, TimeWizard 142

Application, TimeWizard Software Installation 142

Applications, TimeSource 3500 20

B

BesTime algorithm 28, 33

BesTime Ensemble Timing Generator 28, 33–34

298

TimeSource 3500

Index

097-72050-01 Issue 7: August 2003

S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S

C

Cancel User 174, 178

CCK Outputs 289–290

Cisco Systems specifications 279

Communication port 1 specifications 274

Communication port 2 specifications 275

Communication, Edit 174, 184–187

Communication, Retrieve 175, 211–213

Communications, Edit 137, 139, 174, 184–187

Composite Clock Outputs specifications 289–290

Condition All, Retrieve 175, 214

Condition Equipment, Retrieve 175, 215–216

Copy Memory 141, 174, 179–181

Craft port specifications 276

CRIT lamp 39

D

Date, Edit 133–134, 174, 188–190

Delete Equipment 174, 182

Delete User Security 174, 183

Device, strike termination 31

Device, strike termination, lower 31

3

E

E1/T1 Outputs, Mixed 34, 66, 115, 286

Edit Communication 174, 184–187

Edit Communications 137, 139, 174, 184–187

Edit Date 133–134, 174, 188–190

Edit Equipment 132, 135–136, 138, 140, 174, 191–200

Element Manager 36–37, 138–139

Enter Equipment 134, 174, 201–202

Enter User Security 174, 203

Equipment, Delete 174, 182

Equipment, Edit 132, 135–136, 138, 140, 174, 191–200

TimeSource 3500

Index

097-72050-01 Issue 7: August 2003

299

5

S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S

Equipment, Enter 134, 174, 201–202

Equipment, Retrieve 134, 175, 217–226

Error message troubleshooting 257

Ethernet port specifications 277

Event, "BT3 Warmup" 39

Event, "Holdover" 40–41

Event, "Power Up Restart" 39

Event, "Settling Period" 39

Event/alarm, "Holdover" 41

F

Feature, Network Time Protocol (NTP) 33

Feature, NTP 33

Feature, Passthrough 37–38

Frame ground with ground rod 112

Frame ground without ground rod 112

Front panel items troubleshooting 254–256

G

Generator, BesTime Ensemble Timing 28, 33–34

GPS antennas 21

GPS navigation system 21

GPS signals 20

GPS Status, Retrieve 175, 227–228

Ground rod, frame ground with 112

Ground rod, frame ground without 112

H

Header, Retrieve 175, 229

I

Initialize Log 174, 204

Initialize Register 135, 174, 205

Initialize System 175, 206

300

TimeSource 3500

Index

097-72050-01 Issue 7: August 2003

S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S

Installation, mechanical window antenna 78, 95

Installation, roof antenna 77, 87–92

Installation, self-adhesive window antenna 79, 98

Installation, TimeSource 3500 shelf 81, 108

Installation, wall antenna 80, 100–107

Inventory, Retrieve 175, 230–232

IRIG-B TOD Outputs specifications 280

K

Kit, lightning protector 32, 75

Kit, mechanical window antenna 72

Kit, roof antenna 71

Kit, self-adhesive window antenna 73

Kit, wall antenna 74

L

Lamp, CRIT 39

Lightning protector kit 32, 75

Location, roof antenna 48

Location, window or wall antenna 56

Log, Initialize 174, 204

Log, Retrieve 175, 233

Lower strike termination device 31

M

Manager, Element 36–37, 138–139

Mechanical antenna 22

Mechanical window antenna 25, 30

Mechanical window antenna installation 78, 95

Mechanical window antenna installation procedures 93

Mechanical window antenna kit 72

Mechanical window antenna specifications 272

Memory, Copy 141, 174, 179–181

Mixed E1/T1 Outputs 34, 66, 115, 286

TimeSource 3500

Index

097-72050-01 Issue 7: August 2003

301

3

5

S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S

Mixed E1/T1 Outputs specifications 286

Mixed T1/CCK Outputs 34, 67, 116, 288

Mode, "Bridging" 40

Mode, "Holdover" 40

N

Navigation system, GPS 21

Network Time Protocol (NTP) feature 33

Network Time Protocol specifications 278

NTP feature 33

O

Office Alarms specifications 292

Operate Alarm Cutoff All 175, 207

Outputs, CCK 289–290

Outputs, Mixed E1/T1 34, 66, 115, 286

Outputs, Mixed T1/CCK 34, 67, 116, 288–289

Outputs, synchronization 20

Outputs, T1 283–285, 287–288

P

Passthrough feature 37–38

Performance Monitoring, Retrieve 175, 234–249

Power specifications 294

Procedure, RS-422-to-RS-232 converter installation 121

Procedures, mechanical window antenna installation 93

Procedures, roof antenna installation 87–92

Procedures, self-adhesive window antenna installation 97–99

Procedures, wall antenna installation 100–107

Protection, zone of 30–32

Protocol, Simple Network Time 33, 293

R

Register, Initialize 135, 174, 205

302

TimeSource 3500

Index

097-72050-01 Issue 7: August 2003

S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S

Retrieve Alarm All 175, 208

Retrieve Alarm Equipment 175, 209–210

Retrieve Communication 175, 211–213

Retrieve Condition All 175, 214

Retrieve Condition Equipment 175, 215–216

Retrieve Equipment 134, 175, 217–226

Retrieve GPS Status 175, 227–228

Retrieve Header 175, 229

Retrieve Inventory 175, 230–232

Retrieve Log 175, 233

Retrieve Performance Monitoring 175, 234–249

Retrieve User Security 175, 250

RJ-422-to-RJ-232 TOD Converter Kit 61

Roof antenna 22, 24, 30

Roof antenna installation 77

Roof antenna installation procedures 87–92

Roof antenna kit 71

Roof antenna location 48

Roof antenna specifications 272

RS-422-to-RS-232 converter installation procedure 121

S

Self-adhesive window antenna 22, 26, 30

Self-adhesive window antenna installation 79, 98

Self-adhesive window antenna installation procedures 97–99

Self-adhesive window antenna kit 73

Self-adhesive window antenna specifications 273

Set Source Identifier 175, 251

Shelf Environmental specifications 295

Shelf Mechanical specifications 294

Shelf, TimeSource 3500 22, 62

Signals, GPS 20

Simple Network Time Protocol 293

Site survey 46–47

TimeSource 3500

Index

097-72050-01 Issue 7: August 2003

303

3

5

S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S

Source Identifier, Set 175, 251

Specifications, 1 PPS Output 282

Specifications, 10 MHz Output 291

Specifications, Cisco Systems 279

Specifications, communication port 1 274

Specifications, communication port 2 275

Specifications, Composite Clock Outputs 289–290

Specifications, Craft port 276

Specifications, Ethernet port 277

Specifications, IRIG-B TOD Outputs 280

Specifications, mechanical window antenna 272

Specifications, Mixed E1/T1 Outputs 286

Specifications, Network Time Protocol 278

Specifications, Office Alarms 292

Specifications, power 294

Specifications, roof antenna 272

Specifications, self-adhesive window antenna 273

Specifications, Shelf Environmental 295

Specifications, Shelf Mechanical 294

Specifications, T1 Inputs 281

Specifications, T1 Outputs 283

Specifications, wall antenna 273

Standard for the Installation of Lightning Protection Systems (NFPA 780) 30

Strike termination device 31

Survey, site 46–47

Synchronization outputs 20

System, Initialize 175, 206

T

T1 Inputs specifications 281

T1 Outputs 283–285, 287–288

T1 Outputs specifications 283

TimeServer 33

TimeSource 3500 applications 20

304

TimeSource 3500

Index

097-72050-01 Issue 7: August 2003

S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S

TimeSource 3500 shelf 22, 62

TimeSource 3500 shelf installation 81

TimeWizard application 142

TimeWizard Software Installation application 142

TOD Converter Kit, RJ-422-to-RJ-232 61

Troubleshooting, error message 257

Troubleshooting, front panel items 254–256

Types, antenna 22

U

User Security, Delete 174, 183

User Security, Enter 174, 203

User Security, Retrieve 175, 250

User, Activate 131, 174, 177

User, Cancel 174, 178

W

Wall antenna 22, 27, 30

Wall Antenna Indoor Lightning Suppressor Kit 75

Wall Antenna Indoor Lightning Suppressor Kit, Installation 102

Wall antenna installation 80, 100–101

Wall antenna installation procedures 100–107

Wall antenna kit 74

Wall Antenna Outdoor Lightning Suppressor Kit 75

Wall Antenna Outdoor Lightning Suppressor Kit, Installation 104

Wall antenna specifications 273

Window or wall antenna location 56

3

Z

Zone of protection 30–32

5

TimeSource 3500

Index

097-72050-01 Issue 7: August 2003

305

S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S S

306

TimeSource 3500

Index

097-72050-01 Issue 7: August 2003

advertisement

Related manuals

advertisement