Copy Memory. Symmetricom TimeSource 500

Add to My manuals
306 Pages

advertisement

Copy Memory. Symmetricom TimeSource 500 | Manualzz

3

S S S S S S S S S S S S S S S S S S S S S S S S S S S S S

Procedure I. TimeWizard Installation and Operation (cont’d)

Step

12

Procedure

After the Download Progress dialog box closes, continue to monitor the messages reported in the Commands area of the screen.

After the firmware file finishes downloading from the PC to the TimeSource, the

TimeSource requires more time to complete the firmware upgrade process.

During this time, it should not be interrupted. When the firmware upgrade is fully complete, TimeWizard automatically advances to the next screen.

After the screen automatically advances, continue with the next step.

Download the TS3000.hex Firmware

13

Note: If you are not downloading TS3000.hex firmware, click the Next>> button again, then skip to Step 18.

14

15

The “Download TS3000.hex” screen appears very similar to the “Download

GPS.hex” screen shown in Step 8, and contains the same information.

Click the ver Unknown button to open the Load TS3000 File dialog box, which appears very similar to the dialog box shown in Step 9.

In the Load TS3000 File dialog box, navigate to the TS3000.hex firmware file to be downloaded, then click the Open button.

After the Open button is clicked, the message “ Verifying version for

C:\ directory \ts3000.hex (approx 30 secs) ” appears in the

Command area of the screen. Once TimeWizard has verified that the version of the firmware is correct, the text on the ver Unknown button changes to show the version of the firmware to be downloaded.

After TimeWizard verifies the firmware version, select the Download

TS3000.hex check-box, then click the Next>> button to start the firmware download operation.

148

TimeSource 3500

Installation

097-72050-01 Issue 7: August 2003

S S S S S S S S S S S S S S S S S S S S S S S S S S S S S

Procedure I. TimeWizard Installation and Operation (cont’d)

Step

16

Procedure

When the firmware download operation starts, the Download Progress dialog box appears.

As the download operation proceeds, the value in the Packet field increases, and the Progress bar shows the progress of the operation. When the firmware download is complete, the Download Progress dialog box closes.

After the Download Progress dialog box closes, continue with the next step.

Notes:

1. The firmware download operation can be aborted at any time by clicking the Cancel button in the Download Progress dialog box.

2. If the download fails for any reason, a screen appears with instructions to contact Symmetricom. If this happens, exit the application, check the cable connections, and restart TimeWizard.

1

3

4

TimeSource 3500

Installation

097-72050-01 Issue 7: August 2003

149

5

3

S S S S S S S S S S S S S S S S S S S S S S S S S S S S S

Procedure I. TimeWizard Installation and Operation (cont’d)

Step

17

Procedure

After the Download Progress dialog box closes, continue to monitor the messages reported in the Commands area of the screen.

After the firmware file finishes downloading from the PC to the TimeSource, the

TimeSource requires more time to complete the firmware upgrade process.

During this time, it should not be interrupted. When the firmware upgrade is fully complete, TimeWizard automatically advances to the next screen.

Note: After the TS3000.hex download operation successfully completes, the

TimeSource reboots so that it can use the newly installed firmware. Upon rebooting, the system’s output might enter the degraded region of the PRS mask for up to one hour. For systems equipped with a Rubidium internal oscillator, the system output will be within the PRS mask if the unit has been in service and alarm free for more than 24 hours. Systems with Rubidium oscillators are the

090-72050-xx and the 090-72060-xx.

After the screen automatically advances, continue with the next step.

150

TimeSource 3500

Installation

097-72050-01 Issue 7: August 2003

advertisement

Related manuals

advertisement