Specifications. Exmark QUEST QZS708GEM50200


Add to my manuals
72 Pages

advertisement

Specifications. Exmark QUEST QZS708GEM50200 | Manualzz

Specifications

Specifications

Systems

Engine

• Engine Specifications: See your Engine Owner’s

Manual

• Engine Oil Type: Exmark 4-Cycle Premium

Engine Oil

• RPM:

Full Speed: 3300 ±100 (max) RPM (No Load)

Idle: 1650 (min) RPM

Fuel System

• Capacity: 3.0 gal. (11 L)

• Fuel Recommendations:

– For best results, use only clean, fresh, unleaded gasoline with an octane rating of 87 or higher

((R+M)/2 rating method).

– Oxygenated fuel with up to 10% ethanol or

15% MTBE by volume is acceptable.

– Do Not use ethanol blends of gasoline (such as E15 or E85) with more than 10% ethanol by volume. Performance problems and/or engine damage may result which may not be covered under warranty.

– Do Not use gasoline containing methanol.

– Do Not store fuel either in the fuel tank or fuel containers over the winter unless a fuel stabilizer is used.

– Do Not add oil to gasoline.

• Fuel Filter: In-line

Electrical System

• Charging System: Flywheel Alternator

• Charging Capacity: 15 amps

• Battery Type: 195 CCA

• Battery Voltage: 12 Volt

• Polarity: Negative Ground

• Fuses: One 30 amp, one 25 amp; blade type

Safety Interlock System

• PTO must be disengaged, brake engaged, and motion control levers out (neutral lock) to start engine. (It is not necessary for the operator to be in the seat to start the engine.)

• Operator must be in seat when PTO is engaged, brake is disengaged, or motion control levers are moved in or engine will stop.

• Engine will stop if either the left, the right, or both levers are moved from neutral lock position while brake is engaged.

Operator Controls

• Steering and Motion Control:

Note: Motion control levers are adjustable to two heights.

– Separate levers, on each side of the console, control speed and direction of travel of the respective drive wheels.

– Steering is controlled by varying the position of the levers relative to each other.

– Moving motion control levers outward (in slots) locks the drive system in neutral.

• PTO Engagement Switch: Engages electric clutch

(to drive belt) which engages mower blades.

• Parking Brake Lever: Engages/Disengages parking brake.

• Deck Height Adjustment Lever: Sets cutting height to desired position.

• Deck Lift Assist Lever: Foot pedal that assists in raising the deck.

Seat

• Type:

– E-Series models: Standard seat with high back, foam padded with spring suspension and armrests.

– S-Series models: Two tone upholstered high back, foam padded seat with spring suspension and armrests.

• Mounting: Hinged to tilt up for access to battery and other components. Adjustable fore and aft.

• Armrests (S-Series Only): Standard–padded flip-up armrests.

• Seat Safety Switch: Incorporated into the Safety

Interlock System.

Hydrostatic Ground Drive System

• Hydrostatic Pumps:

15

Specifications

– 34 and 42 inch E-Series model: Two Hydro

Gear ZT2100 Integrated drive systems.

– 50 and 60 inch S-Series model: Two Hydro

Gear ZT2800 Integrated drive systems.

• Hydraulic Oil Type: Exmark Premium Hydro Oil.

• Hydraulic Filter—50 and 60 inch S-Series: P/N

109-3321

• Hydro Service Kit—50 and 60 inch S-Series: P/N

135-2307

• Speeds:

– 0-7.0 mph (11.3 km/hr) forward.

– 0-5.0 mph (8.0 km/hr) reverse.

• Drive wheel releases, located on left and right sides of engine deck, allow machine to be moved when the engine is not running and brake is off.

Tires and Wheels

Deck Size

Quantity

Tread

Size

Ply Rating

Pressure

Deck Size

Quantity

Tread

Size

Ply Rating

Pressure

Deck Size

Quantity

Tread

Drive

Pneumatic (Air-Filled)

42 34

2

Turf Tech TL

2

Turf Tech TL

18 x 6.00-8

4

13 psi

(90 kPa)

18 x 7.50-8

4

13 psi

(90 kPa)

Drive

Pneumatic (Air-Filled)

60 50

2

Turf Tech TL

2

Turf Tech TL

20 x 10-10

4

13 psi

(90 kPa)

20 x 10-10

4

13 psi

(90 kPa)

Front Caster

Pneumatic (Air-Filled)

34 and 42 50 and 60

2

Smooth

2

Smooth

Size

Ply Rating

Pressure

11 x 4-5

2

13 psi

(90 kPa)

Front Caster

13 x 6.5-6

4

13 psi

(90 kPa)

Cutting Deck

• Cutting Width:

– 34 inch Deck: 34 inches (86 cm)

– 42 inch Deck: 42 inches (107 cm)

– 50 inch Deck: 50 inches (127 cm)

– 60 inch Deck: 60 inches (152 cm)

• Discharge: Side

• Blade Size:

– 34 inch Deck: 17.50 inches (44.5 cm)–Qty: 2

– 42 inch Deck: 21.60 inches (54.9 cm)–Qty: 2

– 50 inch Deck: 17.50 inches (44.5 cm)–Qty: 3

– 60 inch Deck: 20.50 inches (52.1 cm)–Qty: 3

• Blade Spindles: Solid steel spindles with no maintenance bearings.

• Deck Drive: Electric clutch mounted on vertical engine shaft. Blades are driven by one belt

(w/self-tensioning idler) direct from the engine.

• Deck: Full floating deck is attached to out-front support frame. Maximum turf protection is provided with anti-scalp rollers.

Deck design allows for bagging, mulching or side discharge.

• Deck Depth:

– 34 inch Deck: 4.0 inches (10.2 cm)

– 42 inch Deck: 4.0 inches (10.2 cm)

– 50 inch Deck: 4.0 inches (10.2 cm)

– 60 inch Deck: 4.0 inches (10.2 cm)

• Cutting Height Adjustment: A hand deck lift lever with foot assist is used to adjust the cutting height from 1 1/2 inch (3.8 cm) to 4 1/2 inches (11.4

cm) in 1/2 inch (1.3 cm) increments.

• Mulching Kit: Optional.

16

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Key Features

  • 708cc Kawasaki engine delivers reliable power and performance
  • 50" cutting deck with 3 blades provides a wide cutting path for increased productivity.
  • Hydrostatic drive system offers precise control and smooth operation
  • Adjustable seat with armrests ensures operator comfort during extended mowing sessions.
  • High-back seat provides lumbar support and reduces operator fatigue.
  • Electric blade engagement for easy and convenient blade activation
  • Large fuel tank allows for extended mowing time without frequent refueling
  • Hour meter tracks operating time for maintenance scheduling and warranty purposes.

Related manuals

Frequently Answers and Questions

What type of engine does the Exmark QUEST QZS708GEM50200 have?
It has a 708cc Kawasaki engine.
How wide is the cutting deck?
The cutting deck is 50 inches wide.
Does the mower have a hydrostatic drive system?
Yes, it has a hydrostatic drive system for precise control and smooth operation.
Is the seat adjustable?
Yes, the seat is adjustable with armrests for operator comfort.
How long can I mow before refueling?
The large fuel tank allows for extended mowing time without frequent refueling.
How do I activate the blades?
The blades are activated by an electric blade engagement system for easy and convenient operation.
What is the purpose of the hour meter?
The hour meter tracks operating time for maintenance scheduling and warranty purposes.

advertisement

Table of contents