Check Safety Interlock System. Exmark LAZER Z

Add to My manuals
64 Pages

advertisement

Check Safety Interlock System. Exmark LAZER Z | Manualzz

Maintenance

WARNING

Incorrect installation of the blade or components used to retain the blade can be dangerous. Failure to use all original components and assembled as shown could allow a blade or blade component to be thrown out from under the deck resulting in serious personal injury or death.

Always install the original Exmark blades, blade bushings, and blade bolts as shown.

Check Safety Interlock

System

Service Interval: Before each use or daily

Note: To prevent engine cut-outs on rough terrain the seat kill switch has a 1/2 second delay.

1. Check starting circuit. Starter should crank with, parking brake engaged , PTO disengaged and motion control levers moved out in the neutral lock position. The operator does not need to be in the seat to start the engine.

Try to start with operator in seat , parking brake disengaged, PTO disengaged and motion control levers in the neutral lock position - starter must not crank .

Try to start with operator in seat , parking brake engaged, PTO engaged and motion control levers in the neutral lock position - starter must not crank .

Try to start with operator in seat , parking brake engaged , PTO disengaged , and the left motion control lever in , starter must not crank , repeat again with the right lever in , then with both levers in - starter must not crank .

2. Check the kill circuits. Run engine at one-third throttle, disengage parking brake and raise off of seat (but do not get off of machine) engine must initiate shutdown after approximately 1/2 second has elapsed (seat has time delay kill switch to prevent cut-outs on rough terrain).

Run engine at one-third throttle, engage PTO and raise off of seat (but do not get off of machine) engine must initiate shutdown after one second has elapsed if the handles are in. The delay will be 1/2 second if the handles are out.

Run engine at one-third throttle, with brake disengaged, move levers in and raise off seat (but do not get off of machine) engine must initiate shutdown after 1/2 second has elapsed.

Again, run engine at one-third throttle, brake engaged , and move left motion control lever in - engine must initiate shutdown after 1/2 second has elapsed.

Repeat again moving the right lever in , then moving both levers in - engine must initiate shutdown after 1/2 second has elapsed whether operator is on seat or not .

Note: If machine does not pass any of these tests, do not operate. Contact your authorized EXMARK

SERVICE DEALER.

Important: It is essential that operator safety mechanisms be connected and in proper operating condition prior to use for mowing.

Check Rollover Protections

Systems (Roll Bar) Knobs

Service Interval: Before each use or daily

Check that both the mounting hardware and the knobs are in good working condition. Make sure the knobs are fully engaged with the ROPS in the raised position. The upper hoop of the roll bar may need to be pushed forward or pulled rearward to get both knobs fully engaged.

1.

Engaged

Figure 23

2.

Partially engaged — Do

Not operate with ROPS in this condition.

33

advertisement

Key Features

  • Powerful engine for superior cutting performance
  • Durable deck for long-lasting use
  • Variety of cutting widths to meet your needs
  • Intuitive controls for easy operation
  • Easy maintenance for less downtime
  • Excellent cutting performance for a beautiful lawn

Related manuals

Frequently Answers and Questions

What is the difference between the LAZER Z and other zero-turn mowers?
The LAZER Z is a commercial-grade mower that is built to last. It has a more powerful engine, a more durable deck, and a wider range of cutting widths than most other zero-turn mowers.
How do I choose the right cutting width for my needs?
The right cutting width for you depends on the size of your lawn. If you have a small lawn, a 42-inch cutting width will be sufficient. If you have a larger lawn, you may want to choose a 48-inch or 52-inch cutting width.
How do I maintain my LAZER Z mower?
The LAZER Z mower is easy to maintain. Simply follow the maintenance schedule in the owner's manual.