Copper-Based Anti-seize. Exmark LAZER Z

Add to My manuals
64 Pages

advertisement

Copper-Based Anti-seize. Exmark LAZER Z | Manualzz

Maintenance

Thread locking adhesives are required for some hardware on engines — see the Engine manual.

Copper-Based Anti-seize

Copper-based anti-seize is used in the following location:

On threads of Blade Bolts. See Check Mower

Blades section.

Dielectric Grease

Dielectric grease is used on all blade type electrical connections to prevent corrosion and loss of contact.

Adjustments

Note: Disengage PTO, shut off engine, wait for all moving parts to stop, engage parking brake, and remove key before servicing, cleaning, or making any adjustments to the unit.

CAUTION

Raising the mower deck for service or maintenance relying solely on mechanical or hydraulic jacks could be dangerous. The mechanical or hydraulic jacks may not be enough support or may malfunction allowing the unit to fall, which could cause injury.

Do Not rely solely on mechanical or hydraulic jacks for support. Use adequate jack stands or equivalent support.

Deck Leveling

1. Position the mower on a flat surface.

2. Stop engine, wait for all moving parts to stop, and remove key. Engage parking brake.

3. Check the tire pressure in the drive tires. Proper inflation pressure for tires is 13 psi (90 kPa).

Adjust if necessary.

4. Position the transport lock in the latching position.

5. Push the foot pedal all the way forward and the deck will latch at the 5 1/2 inch (14 cm) transport position (Figure 29).

40

1.

Foot lever

2.

Height of cut pin

Figure 29

3.

Transport lock

Maintenance

6. Insert the height adjustment pin into the 3 inch

(7.6 cm) cutting height location.

7. Release the transport lock and allow the deck to lower to the cutting height.

8. Raise the discharge deflector.

9. Measure from the level surface to the front tip of the center blade. The measurement should read

3 inches (7.6 mm).

Note: In most conditions, the back tips on the side blades should be adjusted 1/4 inch (6.4 mm) higher than the front.

1.

Whizlock nut

2.

Adjuster screw

Figure 31

3.

Jam nut

4.

Yoke

11. The back tips of the side blades should measure

3 1/4 inches (8.3 cm). Fine tune rear adjusters as required.

12. Re-measure until all four sides are the correct height. Tighten all the nuts on the deck lift arm assemblies.

13. Lower discharge deflector.

14. If the four deck links do not have enough adjustment to achieve accurate cut height with the desired rake, the single point adjustment can be utilized to gain more adjustment (see Figure 32).

1.

3 1/4 inches (8.3 cm)

2.

Back blade tip

3.

Front blade tip

Figure 30

4.

3 inches (7.6 cm)

5.

Level surface

10. Loosen the whizlock nut on the side of the yoke and the jam nut on top. Fine tune the screw adjuster by turning it to get 3 inch (7.6 mm) height (see Figure 31).

To increase the height, turn the adjuster screw clockwise; to decrease, turn counterclockwise.

41

Figure 32

1.

Single point height adjustment bolt

2.

Front height-of-cut plate mounting bolt

3.

Rear height-of-cut plate mounting bolt

15. To adjust the single point system, first loosen the front and rear height-of-cut plate mounting bolts.

advertisement

Key Features

  • Powerful engine for superior cutting performance
  • Durable deck for long-lasting use
  • Variety of cutting widths to meet your needs
  • Intuitive controls for easy operation
  • Easy maintenance for less downtime
  • Excellent cutting performance for a beautiful lawn

Related manuals

Frequently Answers and Questions

What is the difference between the LAZER Z and other zero-turn mowers?
The LAZER Z is a commercial-grade mower that is built to last. It has a more powerful engine, a more durable deck, and a wider range of cutting widths than most other zero-turn mowers.
How do I choose the right cutting width for my needs?
The right cutting width for you depends on the size of your lawn. If you have a small lawn, a 42-inch cutting width will be sufficient. If you have a larger lawn, you may want to choose a 48-inch or 52-inch cutting width.
How do I maintain my LAZER Z mower?
The LAZER Z mower is easy to maintain. Simply follow the maintenance schedule in the owner's manual.