Mechanical installation 21
4
Mechanical installation
10
Contents of this chapter
This chapter gives guidelines for the mechanical installation of the drive module into a cabinet.
Safety
WARNING!
For frame sizes R4 to R9: Use the lifting eyes of the drive when you lift the drive.
Do not tilt the drive. The drive is heavy and its center of gravity is high. An overturning drive can cause physical injury.
4
22 Mechanical installation
Examining the installation site
See the drive hardware manual for
• allowed ambient conditions in chapter Technical data
• allowed installation positions.
Examine the installation site:
• The installation site is sufficiently ventilated or cooled to remove heat from the drive.
See the technical data.
• The ambient conditions of the drive meet the specifications. See the technical data.
• The wall behind the unit and the material above and below the unit is of non-flammable material.
• The installation surface is as close to vertical as possible and strong enough to support the drive.
• There is enough free space around the drive to enable cooling, maintenance, and operation. See the free space specifications for the drive.
• Make sure that there are no sources of strong magnetic fields such as high-current single-core conductors or contactor coils near the drive. A strong magnetic field can cause interference or inaccuracy in the operation of the drive.
Necessary tools
• Drill and drill bits
• Screwdriver and/or wrench with bits.
Moving the drive module
Move the transport package by pallet truck to the installation site.
Mechanical installation 23
Unpacking and examining the delivery
Examine that all items are present and there are no signs of damage. Read the data on the type designation label of the drive to make sure that the drive is of the correct type.
■
ACS880-01 frames R1 and R2
The figure below shows the drive package with its contents.
3AXD50000015224
1
2
Mounting template
Cardboard sleeve
9
10
Cardboard trays
Straps
3…5 Cardboard supports
6…8 Cushions
11
12
Plastic bag
Drive with factory installed options
To unpack:
• Cut the straps (10)
• Remove the top cardboard tray (9), mounting template (1), cardboard support (4) and cushions (7 and 8)
• Lift the sleeve (2)
• Remove the cardboard supports (5)
• Lift the drive module.
10
24 Mechanical installation
■
ACS880-01 frame R3
The figure below shows the drive package with its contents.
4
3
4
5
1
2
Cardboard trays
Mounting template
Cardboard sleeve
Cardboard spacer
Cardboard support
To unpack:
• Cut the straps (9)
• Remove the top cardboard tray (1), mounting template (2) and cushions (7 and 8)
• Lift the sleeve (3)
• Remove the cardboard spacer (4)
• Lift the drive module.
3AXD50000010880
6…8 Cushions
9 Straps
10 Plastic bag
11 Drive with factory installed options
■
ACS880-01 frame R4
The figure below shows the drive package with its contents.
Mechanical installation 25
3AXD50000006259
1 Straps
2
6
Cardboard support
3…5 Cushions
Sleeve
8
9
10
11
Drive with factory installed options
Cardboard spacer
CDPI-01 assembly kit
Main cable clamp kit
7 Trays 12 Panel holder
To unpack:
• Cut the straps (1)
• Remove the top tray (7)
• Remove the cardboard spacer (9), cushions (5), cardboard support (2), panel holder (12) and main cable clamp kit (11)
• Remove the sleeve
• Attach lifting hooks to the lifting eyes of the drive module. Lift the drive module with a hoist.
10
26 Mechanical installation
■
ACS880-01 frame R5
The figure below shows the drive package with its contents.
4
3AXD50000006291
1
2
Straps
Drive with factory installed options
6
7
Cardboard spacer
Sleeve
3 Cardboard box for panel holder
4…5 Cushions
8
9
Trays
Panel holder
To unpack:
• Cut the straps (1)
• Remove the top tray (8), cushions (4), cardboard spacer (6) and cardboard box for panel holder (3)
• Remove the sleeve (7).
• Attach lifting hooks to the lifting eyes of the drive module. Lift the drive module with a hoist.
■
ACS880-01 frames R6 to R9
The figure below shows the drive package with its contents.
Mechanical installation 27
3AXD50000012445
1 Drive with factory installed options 4 Pallet tray
2
3
Cardboard cover
Stopper
5
6
VCI bag
Straps
To unpack:
• Cut the straps (6)
• Remove the cardboard cover (2)
• Remove the stopper (3)
• Attach lifting hooks to the lifting eyes of the drive module. Lift the drive module with a hoist.
10
4
28 Mechanical installation
■
ACS880-11 and ACS880-31 frame R3
The figure below shows the drive package with its contents.
2
1
7
2
3
3AXD50000041449
1
2
3
Mounting template
Straps
Drive with factory installed options
4
5
Trays
Sleeve
6…7 Package cushion
To unpack:
• Cut the straps (2)
• Remove the top tray (4), sleeve (5), mounting template (1) and cushion (7)
• Lift the drive.
6
4
4
5
■
ACS880-11 and ACS880-31 frame R6
The figure below shows the drive package with its contents.
Mechanical installation 29
4 7
9
4 a
11
3
5 b
6
2
1
10
8
3AXD50000038252
10
1
2
3
4
5
6
Printed quick guides and manuals, multilingual residual voltage warning sticker
Accessories
Mounting template
Straps
Plastic bag
Drive with factory installed options
7
8
9
10
11
Cardboard cover
Pallet
VCI bag
Plywood support
Packing brackets and screws
To unpack:
• Cut the straps (4)
• Remove the cardboard cover (7)
• Undo the attaching screws (b) and packing brackets (a)
• Attach lifting hooks to the lifting eyes of the drive module. Lift the drive module with a hoist.
4
30 Mechanical installation
■
ACS880-11 and ACS880-31 frame R8
The figure below shows the drive package with its contents.
7
8
1
5
4
2
3
4 a
11
6 b
12
9
10
3AXD50000106974
1
2
3
4
5
6
Printed quick guides and manuals, multilingual residual voltage warning sticker
VCI bag
Mounting template
Straps
Plastic bag
Packing brackets
7
8
9
10
11
12
Tray
Sleeve
Plywood supports
Pallet
Drive with factory installed options
Screws
To unpack:
• Cut the straps (4)
• Remove the top tray (7), sleeve (8) and mounting template (3)
• Undo the packing brackets (a) and attaching screws (b)
• Attach lifting hooks to the lifting eyes of the drive module. Lift the drive module with a hoist.
Mechanical installation 31
Installing the drive
1.
See the dimension drawings. Mark the locations for the four mounting holes.
2.
Start the screws or bolts into the mounting holes.
3.
Position the drive onto the screws.
4.
Tighten the screws in the wall securely.
x 4
10
32