Remote. Samsung svr-945, svr-1680c, SVR-1645, svr-480, SVR-PC, SVR-3200, SVR-1660C, SVR-960C

Add to my manuals
122 Pages

advertisement

Remote. Samsung svr-945, svr-1680c, SVR-1645, svr-480, SVR-PC, SVR-3200, SVR-1660C, SVR-960C | Manualzz

User Manual

This turns NTP on or off.

NTP Mode

This sets NTP Mode to Client, Server or All.

NTP Server Location

This is enabled when NTP Mode is set to Client. This determines whether the NTP server is on a local network or on the Internet.

NTP Local Server IP

This is enabled when the NTP Server Location is set to Local and is used to set the IP of the

NTP server. Enter either the IP of an NTP server on the local network or the IP of a DVR with its

NTP mode set to Server.

Interval

This menu is used to set the synchronization interval.

When NTP Mode is set to Client, Sync With NTP must be set to On.

6.8.4 Remote

DVR ID

This sets the address of the keyboard when operating all DVR functions with the controller buttons. The default value is "1". If one keyboard is connected to several DVRs, it might conflict with other channels, so a different value should be set for the keyboard address.

84

User Manual

Remote Controller ID

Up to 16 remote controller IDs can be set. You can use one remote controller to operate up to

16 DVRs.

How to register the remote controller is as shown below.

-

Direct the remote controller to the DVR.

-

Press the [ID] button based on the specified remote controller ID.

-

If the remote controller ID and the DVR ID are the same, the DVR buzzer beeps.

-

The remote controller is now configured and available for use.

Remote Configuration Setup

This determines whether to use the SNM Configuration program for setup.

If "Enable" is set, SNM Configuration is available for setup. If "Disable" is set, SNM

Configuration is unavailable for setup.

Remote Relay

Remote Relay is used to determine whether to use the Relay On/Off function on the SNM monitor.

If "Enable" is set, all four relays can be controlled remotely. If "Disable" is set, remote control is unavailable with the SNM Configuration.

A total of four serial ports are available for the DVR. Two are RS-232C(Com1, Com3) and the other two are RS-422/485(Com2, Com4).

The Serial Port settings are available under Communication > Remote.

The following options are provided for the Serial Port settings.

A total of 3 serial ports are available for SVR-480. One is RS-232C(Com1), and the other two are RS-485(Com2,3).

85

User Manual

To use the Text option, please follow the instructions below.

Please note that the Text option supports only Com1 (RS-232); make sure to select Com1 on the Serial Port menu.

Device

Select Text.

Interface

Select RS-232.

Baud rate/Parity/Stop Bit/Data Bit

Enter the same settings as the ones for the selected TP device.

To use a transparent device, please follow the instructions below.

86

User Manual

Device

Select a connected transparent device.

Interface

Select COM1 or COM3.

Only Com1 is available for SVR-480.

Baud rate/Parity/Stop Bit/Data Bit

Enter the same settings as the ones for the selected Transparent device.

To set up a keyboard, select Keyboard for the Device option, and then select a keyboard model.

Device

Select Keyboard.

Keyboard

Select a desired keyboard model.

Interface

87

Select COM1 or COM3.

Only Com1 is available for SVR-480.

Baud rate/Parity/Stop Bit/Data Bit

Enter the same settings as the ones for the selected keyboard.

User Manual

Select PTZ.

To control the PTZ operation via serial port, select PTZ in the Device options, and then set up a serial port; refer to 6.8.4.2.2 PTZ (Serial).

To control the PTZ operation via coax protocol, you do not need to set up this option. (Refer to

6.8.4.2 PTZ.)

Device

Select a connected PTZ device.

6.8.4.2 PTZ

Two PTZ control methods are available: via serial port and coax protocol.

88

User Manual

The Coax Protocol option does not support normal PTZ protocols, but rather supports the Pelco

Standard and Extended Protocols.

The standard protocol supports basic PTZ functions such as PTZ and presets. The extended protocol supports more expansive features such as menu control and video playback in addition to the basic PTZ functions.

To use this option, a PTZ device must be embedded with a coax standard or extended protocol.

SVR-3200, SVR-1645, SVR-945, SVR-480 does not support coaxial function.

Type

Select Coax.

Protocol

Select Pelco or Pelco Extended according to the coax protocol type of Pelco camera.

AD Dome does not support menu control, Presets or AUX when setup with a coax protocol.

Idle Time

Activate or disable PTZ Home, and setup a standby duration of the device before moving to

PTZ home.

Select PTZ.

89

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement

Table of contents