Automatic Non-Stop programme or programmes. Electrolux EW7W3164LB

Add to my manuals
48 Pages

advertisement

Automatic Non-Stop programme or programmes. Electrolux EW7W3164LB | Manualzz

WARNING!

Refer to Safety chapters.

This appliance is an automatic washer dryer.

11.1 Complete wash&dry programme

Automatic Non-Stop programme or programmes

Depending on the model, the appliance may be equipped with one or more

OneGo programmes, automatic wash&dry programmes where it is not necessary to set the Dry.

Proceed as follows:

1. After loading laundry and detergent, press the On/Off button for some seconds to activate the appliance.

2. Set the OneGo programme by means of the programme dial. The indicators and appear on the display.

3. Touch the Start/Pause button to start the programme.

ENGLISH

3. When the programme is completed and the door locked indicator goes off, you can open the door.

4. Press the On/Off button for a few seconds to deactivate the appliance.

10.14 Stand-by function

The Stand-by function automatically deactivates the appliance to reduce the energy consumption when:

• You do not use the appliance for 5 minutes when no programme is running.

Press the button On/Off to activate the appliance again.

• 5 minutes after the end of the washing programme.

Press the On/Off button to activate the appliance again.

The display shows the end of the last programme.

Turn the programme dial to set a new cycle.

If the dial is rotated to the "Reset" position , the appliance automatically turns off in 30 seconds.

If you set a programme or an option that ends with water in the drum, the Stand-by function doesn't deactivate the appliance to remind you to drain the water.

11. DAILY USE - WASHING & DRYING

29

Non-automatic wash&dry programmes

In some washing programmes, you can combine Wash and Dry for running a complete wash&dry programme.

Proceed as follows:

1. Press the On/Off button for some seconds to activate the appliance.

2. Load the laundry one item at a time.

3. Put the detergent and the additives in the appropriate compartment.

4. Turn the programme dial to the washing programme. The appliance defaults to the washing only mode and the indicator of the Wash button is on. The display shows the default temperature and spin. If necessary, change them according to your laundry. The display also shows the maximum recommended load for washing phase.

5. Set the desired options, if there are available.

6. Tap on the Dry button to activate also the drying function. Both indicators of the Wash and Dry buttons are on.

The indicators and appear on the display. The display also shows the maximum recommended load for a washing and drying programme

(e.g. 6 kg for cottons).

30 www.electrolux.com

11.2 Washing and Drying -

Automatic levels

1. Tap on the Auto Dry button repeatedly until the display shows the required dryness level. The indicators in the display illuminate accordingly: a.

b.

Iron dry: for cotton items;

Cupboard dry: for cotton and synthetic items; c.

Extra dry: for cotton items.

The time value on the display is the duration of both cycles washing and drying, calculated on a default load size.

To have a good drying by using less energy and in a shorter time, the appliance does not let you set a too low spin speed for the items to be washed and dried.

2. Touch button Start/Pause to start the programme. The SensiCare estimation starts.

In the display the door locked indicator comes on.

The display also shows the remaining programme time.

11.3 Washing and Timed

Drying

1. Tap on the Time Dry button repeatedly to set the desired time value (see the "Timed drying" table the "Programmes" chapter). The drying level indicator goes off and the indicator comes on.

Each time you tap on this button the time value increases by 5 minutes. The display shows the set new time value.

2. Touch the Start/Pause button to start the programme. The SensiCare estimation starts.

12. DAILY USE - DRYING ONLY

In the display the door locked indicator comes on.

The display also shows the remaining programme time.

11.4 At the end of the drying programme

• The appliance stops automatically.

• The acoustic signals operate (if they are active).

• In the display comes on.

• The indicator of the Start/Pause button goes off. The door locked

goes off.

The appliance continues to operate with the anti-crease phase for approximately 30 minutes or more if

Anti-crease option was set.

The anti-crease phase reduces creasing.

You can remove the laundry before the anti-crease phase is completed.

We recommend, for better results, that you remove the laundry when the phase is almost completed or completed. The indicator remains lit.

• Press the On/Off button for some seconds to deactivate the appliance.

After some minutes from the end of the programme, the energy saving function deactivates the appliance automatically.

1. Remove the laundry from the appliance.

2. Make sure that the drum is empty.

After drying phase, clean the drum, the seal and the inside of the door with a wet cloth.

WARNING!

Refer to Safety chapters.

This appliance is an automatic washer dryer.

12.1 Preparation to drying

1. Press the On/Off button for some seconds to activate the appliance.

2. Load the laundry one item at a time.

3. Turn the programme dial to the programme suitable for the items to dry. The appliance defaults to the washing only mode and the indicator of the Wash button is on.

4. Tap on the Dry button and then on the Wash button to perform drying only. The indicator of Dry button illuminates and the indicator of Wash button goes off. The indicators and appear on the display and the indicator disappears.

When drying a big amount of laundry, to have good drying performances, make sure that the laundry itself is not rolled up and that is uniformly distributed in the drum.

12.2 Drying - Automatic levels

1. Tap on the Auto Dry button repeatedly until the display shows the required dryness level. The indicators in the display illuminate accordingly: a.

b.

Iron dry: for cotton items;

Cupboard dry: for cotton and synthetic items; c.

Extra dry: for cotton items.

The display shows the drying programme duration.

2. Touch the Start/Pause button to start the programme.

In the display the door locked indicator comes on.

The display also shows the remaining programme time.

12.3 Timed Drying

1. Tap on the Time Dry button repeatedly to set the desired time value (see the "Timed drying" table the "Programmes" chapter). The drying level indicator goes off and the indicator comes on.

ENGLISH 31

Each time you tap on this button the time value increases by 5 minutes. The display shows the set new time value.

2. Touch the Start/Pause to start the programme.

In the display the door locked indicator comes on.

The display also shows the remaining programme time.

12.4 At the end of the drying programme

• The appliance stops automatically.

• The acoustic signals operate (if they are active).

• In the display comes on.

• The indicator of the Start/Pause button goes off. The door locked

goes off.

The appliance continues to operate with the anti-crease phase for approximately 30 minutes or more if

Anti-crease option was set.

The anti-crease phase reduces creasing.

You can remove the laundry before the anti-crease phase is completed.

We recommend, for better results, that you remove the laundry when the phase is almost completed or completed. The indicator remains lit.

• Press the On/Off button for some seconds to deactivate the appliance.

After some minutes from the end of the programme, the energy saving function deactivates the appliance automatically.

1. Remove the laundry from the appliance.

2. Make sure that the drum is empty.

After drying phase, clean the drum, the seal and the inside of the door with a wet cloth.

32 www.electrolux.com

13. FLUFF IN THE FABRICS

During the washing and/or drying phase, some types of fabric, (sponge, wool, sweatshirt) could release fluff.

The released fluff could stick to the fabrics during the next cycle.

This inconvenient increases with technical fabrics.

To prevent the fluff in your laundry, we recommend that you:

• To do not wash dark fabrics after you washed and dried light coloured fabrics (hand towel, wool, sweatshirt ) and the contrary.

• To dry this type of fabrics at open air when they are washed the first time.

• To clean the drain filter.

• After the drying phase, clean the empty drum, the gasket and the door with a wet cloth.

14. HINTS AND TIPS

WARNING!

Refer to Safety chapters.

14.1 The laundry load

• Divide the laundry into: white, coloured, synthetics, delicates and wool.

• Follow the washing instructions on the laundry care labels.

• Do not wash white and coloured items together.

• Some coloured items can discolour with the first wash. We recommend that you wash them separately for the first couple of times.

• Button up pillowcases, close zippers, hooks and poppers. Tie up belts.

• Turn multilayered fabrics, wool and items with printed illustrations inside out.

• Pre-treat tough stains.

• Wash heavy soil stains with a special detergent.

• Be careful with curtains. Remove the hooks and put the curtains in a washing bag or pillowcase.

• Do not wash laundry without hems or with cuts.

To remove the fluff inside the drum, set a special programme:

• Empty the drum.

• Clean the drum, the gasket and the door with a wet cloth.

• Set the Machine Clean programme and the Dry together to activate the anti-fluff action.

• Touch the Start/Pause button to start the programme.

If the appliance is frequently used, carry out the cleaning programme regularly.

• Use a washing bag to wash small and/or delicate items (e.g. underwired bras, belts, tights, etc. ).

• A very small load can cause balance problems with the spin phase leading to excessive vibration. If this occurs:

a. interrupt the programme and open the door (refer to "Daily

Use" chapter);

b. manually redistribute the load so that the items are spaced evenly around the tub;

c. press the Start/Pause button.

The spin phase continues.

• Avoid washing garments full of long animal hair or poor quality garments releasing lots of fluff that could block the drain circuit and therefore requiring the Service assistance.

• Empty pockets and unfold the items.

14.2 Stubborn stains

For some stains, water and detergent is not sufficient.

We recommend that you pre-treat these stains before you put the items in the appliance.

Special stain removers are available.

Use the special stain remover that is applicable to the type of stain and fabric.

Do not spray stain remover on garments near the appliance as it is corrosive to the plastic parts.

14.3 Detergents and other treatments

• Only use detergents and other treatments specially made for washing machines:

– powder detergents for all types of fabric, excluding delicate. Prefer powder detergents containing bleach for whites and laundry sanitization

– liquid detergents, preferably for low temperature wash programmes (60 °C max) for all types of fabric, or special ones for woollens only.

• Do not mix different types of detergents.

• To help the environment, do not use more than the recommended quantity of detergent.

• Follow the instructions that you find on packaging of the detergents or other treatments without exceeding the indicated maximum level ( ).

• Use the recommended detergents for the type and colour of the fabric, the programme temperature and the level of soil.

ENGLISH 33

14.4 Ecological hints

• Set a programme without the prewash phase to wash laundry with normal soil.

• Always start a washing programme with the maximum load of laundry allowed.

• If you pre-treat the stains or use a stain remover, set a programme with a low temperature.

• To use the correct quantity of detergent, check the water hardness of your domestic system. Refer to

"Water hardness".

14.5 Water hardness

If the water hardness in your area is high or moderate, we recommend that you use a water softener for washing machines. In areas where the water hardness is soft it is not necessary to use a water softener.

To find out the water hardness in your area, contact your local water authority.

Use the correct quantity of water softener. Follow the instructions that you find on the packaging of the product.

14.6 Prepare the drying cycle

• Open the water tap.

• Check if the drain hose is connected properly. Refer to installation chapter for more information.

• For the maximum laundry load of the drying programmes, refer to the drying programmes table.

14.7 Items not suitable for drying

Do not set a drying programme for this laundry:

• Synthetic curtains.

• Pieces of clothing with metal inserts.

• Nylon stockings.

• Quilts.

• Bed covers.

• Duvets.

• Anoraks.

• Sleeping bags.

• Fabrics with residue of hair sprays, nail solvents or similar.

34 www.electrolux.com

• Garments with foam-rubber or materials similar to foam-rubber.

14.8 Garment labels

When you dry the laundry, obey the indications on the labels of the manufacturers:

= The item can be tumble dried

= The drying cycle is at high temperature

= The drying cycle is at reduced temperature

= The item can not be tumble dried.

14.9 Drying cycle duration

The drying time can change depending on:

• speed of the last spin

• dryness level

• type of laundry

• weight of the load

14.10 Additional drying

If, at the end of the drying programme, the laundry is still damp, set a short drying cycle again.

15. CARE AND CLEANING

WARNING!

Refer to Safety chapters.

15.1 External cleaning

Clean the appliance with mild soap and warm water only. Fully dry all the surfaces.

CAUTION!

Do not use alcohol, solvents or chemical products.

CAUTION!

Do not clean the metal surfaces with chlorine-based detergent.

WARNING!

To avoid creasing and shrinkage do not overdry the laundry.

14.11 General Tips

Refer to the «Drying programmes» table to find the average drying times.

Experience will help you to dry the laundry better. Take note of the duration of the cycles done before.

To avoid the static charge at the end of the drying cycle:

1. Use fabric conditioner in the washing cycle.

2. Use special fabric conditioner for tumble dryers.

When the drying programme is completed remove the laundry promptly.

15.2 Descaling

If the water hardness in your area is high or moderate, we recommend that you use a water descaling product for washing machines.

Regularly examine the drum to check for limescale.

Regular detergents already contain water softening agents, but we recommend to run a cycle with an empty drum and a descaling product occasionally.

Always follow the instructions that you find on the packaging of the product.

ENGLISH 35

15.3 Maintenance wash

The repeated and prolonged use of low temperature programmes can cause detergent deposits, fluff residues, bacterial growth inside the drum and the tub. This could generate bad odours and mildew. To eliminate these deposits and clean the inner part of the appliance, run a maintenance wash regularly (at least once a month).

Refer to Cleaning the drum chapter.

15.4 Door seal with double lip trap

This appliance is designed with a self

cleaning draining system, allowing light fluff fibers that fall off the clothes to be drained out with the water, in such a way that there is no need by the customer to access this area for regular maintenance and cleaning.

Regularly examine the seal and remove all objects from the inner part. Coins, buttons, other small items forgotten in the pockets of your clothes are deposited during the washing cycle in the special double lip trap in the porthole seal, where they can be conveniently recovered at the end of the cycle.

15.5 Cleaning the drum

Regularly examine the drum to prevent unwanted deposits.

Rust deposits in the drum may occur due to rusting foreign body in the washing or tap water containing iron

Clean the drum with special products for stainless steel.

Always follow the instructions that you find on the packaging of the product.

Do not clean the drum with acidic descaling products, scouring products containing chlorine or iron or steel wool.

For a thorough clean:

1. Remove all laundry from the drum.

2. Run the Machine Clean programme.

For more details, refer to washing programme table.

3. Add a small quantity of powder detergent into the empty drum, in order to rinse out any left residues.

Occasionally, at the end of a cycle the display may show the icon : this is a recommendation to perform the “drum cleaning”. Once the drum cleaning has been performed, the icon disappears.

15.6 Cleaning the detergent dispenser

To prevent possible deposits of dried detergent or clotted fabric softener and/or formation of mould in the detergent dispenser drawer, once in a while carry out the following cleaning procedure:

1. Open the drawer. Press the catch downwards as indicated in the picture and pull it out.

1

2. Remove the top part of the additive compartment to aid cleaning and

2

36 www.electrolux.com

flush it out under running warm water, to remove any traces of accumulated detergent. After cleaning, put the top part back into position.

3. Make sure that all detergent residue is removed from the upper and lower part of the recess. Use a small brush to clean the recess.

15.7 Cleaning the drain pump

WARNING!

Disconnect the mains plug from the mains socket.

Regularly check the drain pump filter and make sure that it is clean.

Clean the drain pump if:

• The appliance does not drain the water.

• The drum does not turn.

• The appliance makes an unusual noise because of the blockage of the drain pump.

• The display shows the alarm code

.

WARNING!

• Do not remove the filter while the appliance operates.

• Do not clean the pump if the water in the appliance is hot. Wait until the water cools down

Proceed as follows to clean the pump:

1. Open the pump cover.

4. Insert the detergent drawer into the guide rails and close it. Run the rinsing programme without any clothes in the drum.

2

1

2. Place a suitable bowl below the drain pump access to collect the water that flows out.

3. Open the chute downwards. Always keep a rag nearby to dry up any water spillages when removing the filter.

ENGLISH contact the Authorised Service

Centre.

37

4. Turn the filter 180 degrees in anticlockwise direction to open it, without removing. Let the water flow out.

10. Clean the filter under the water tap.

5. When the bowl is full of water, turn the filter back and empty the container.

6. Repeat the steps 4 and 5 until the water stops to flow out.

7. Turn the filter anti-clockwise to remove it.

11. Put the filter back into the special guides by turning it clockwise. Make sure that you tighten the filter correctly to prevent leakages.

2

1

1

2

8. If it is necessary, remove fluff and objects from the filter recess.

9. Make sure that the impeller of the pump can rotate. If it does not rotate,

12. Close the pump cover.

38 www.electrolux.com

2

When you drain the water with the emergency drain procedure, you must activate the drain system again:

a. Put 2 litres of water in the main wash compartment of the detergent dispenser.

b. Start the programme to drain the water.

1

15.8 Cleaning the inlet hose and the valve filter

1

2

3

45°

20°

15.9 Emergency drain

If the appliance cannot drain the water, carry out the same procedure, described in 'Cleaning the drain pump' paragraph. If necessary, clean the pump.

When you drain the water with the emergency drain procedure, you must activate the drain system again:

1. Put 2 litres of water in the main wash compartment of the detergent dispenser.

2. Start the programme to drain the water.

15.10 Frost precautions

If the appliance is installed in an area where the temperature can reach values around 0° C or drop below, remove the remaining water from the inlet hose and the drain pump.

1. Disconnect the mains plug from the mains socket.

2. Close the water tap.

3. Put the two ends of the inlet hose in a container and let the water flow out of the hose.

4. Empty the drain pump. Refer to the emergency drain procedure.

ENGLISH

5. When the drain pump is empty, install the inlet hose again.

WARNING!

Make sure that the temperature is higher than

0 °C before you use the appliance again.

The manufacturer is not responsible for damages caused by low temperatures.

16. TROUBLESHOOTING

WARNING!

Refer to Safety chapters.

16.1 Introduction

The appliance does not start or it stops during operation.

First try to find a solution to the problem (refer to the table). If the problem persists, contact the Authorised Service Centre.

WARNING!

Deactivate the appliance before carrying out any check.

In case of major problems, the acoustic signals operate, the display shows an

alarm code and the Start/Pause button may flash continuously:

- The mains supply is unstable. Wait until the mains supply is stable.

- No communication between electronic elements of the appliance. Switch it off and switch on again. The programme was not finished properly or the appliance stopped too early. If the alarm code appears again, contact the Authorised Service

Centre.

- The appliance does not fill with water properly. After the proper check, start the appliance again by pressing Start/Pause button the appliance tries to resume the cycle . If the error persists the alarm code will appear again.

- The appliance does not drain the water.

- The appliance door is open or not closed correctly. Please check the door!

If the appliance is overloaded, remove some items from the drum and/or hold the door shut while touching the Start/Pause button until the indicator stops flashing (see the picture below).

39

40 www.electrolux.com

16.2 Possible failures

Problem

The programme does

The appliance fills with water and drains imme‐ diately

The spin phase does not operate or the washing cycle lasts lon‐ ger than usual.

There is water on the floor.

not start.

The appliance does not fill with water properly.

The appliance does not drain the water.

Possible solution

• Make sure that the mains plug is connected to the mains socket.

• Make sure that the appliance door is closed.

• Make sure that there is no damaged fuse in the fuse box.

• Make sure that the Start/Pause has been touched.

• If the delay start is set, cancel the setting or wait for the end of countdown.

• Deactivate the Child Lock function if it is on.

• Check the position of the knob on the selected pro‐ gramme.

• Make sure that the water tap is open.

• Make sure that the pressure of the water supply is not too low. For this information, contact your local water authority.

• Make sure that the water tap is not clogged.

• Make sure that the inlet hose has no kinks, damages or bends.

• Make sure that the connection of the water inlet hose is correct.

• Make sure that the filter of the inlet hose and the filter of the valve are not clogged. Refer to 'Care and cleaning'.

• Make sure that the drain hose is in the correct position.

The hose may be positioned too low. Refer to "Installa‐ tion instruction".

• Make sure that the sink spigot is not clogged.

• Make sure that the drain hose has no kinks or bends.

• Make sure that the drain filter is not clogged. Clean the filter, if necessary. Refer to "Care and cleaning".

• Make sure that the connection of the drain hose is cor‐ rect.

• Set the drain programme if you set a programme with‐ out drain phase.

• Set the drain programme if you set an option which ends with water in the tub.

• Set the spin programme.

• Make sure that the drain filter is not clogged. Clean the filter, if necessary. Refer to "Care and cleaning".

• Adjust manually the items in the tub and start the spin phase again. This problem may be caused by balance problems.

• Make sure that the couplings of the water hoses are tight and there is not water leakages.

• Make sure that the water inlet hose and the drain hose have no damages.

• Make sure you use the correct detergent and the correct quantity of it.

ENGLISH 41

Problem

You cannot open the appliance door.

The appliance makes an unusual noise and vibrates.

The programme dura‐ tion increases or de‐ creases during pro‐ gramme execution.

The washing results are not satisfactory.

Possible solution

• Make sure that a washing programme that ends with water in tub, has been selected.

• Make sure that the washing programme is finished.

• Set the drain or the spin programme if there is water in the drum.

• Make sure that the appliance receives electrical power.

• This problem may be caused by a failure of the appli‐ ance. Contact the Authorised Service Centre.

If you need to open the door, please read carefully

"Emergency door opening".

• Make sure the levelling of the appliance is correct. Refer to "Installation instruction".

• Make sure that the packaging and/or the transit bolts are removed. Refer to "Installation instruction".

• Add more laundry in the drum. The load may be too small.

• The SensiCare System is able to adjust the programme duration according to the type and the laundry load size.

Refer to "The SensiCare System load detection" in "Dai‐ ly Use" chapter.

• Increase the detergent quantity or use a different deter‐ gent.

• Use special products to remove the stubborn stains be‐ fore you wash the laundry.

• Make sure that you set the correct temperature.

• Decrease the laundry load.

• Reduce the quantity of detergent.

Too much foam in the drum during the wash‐ ing cycle.

After the washing cycle, there are some deter‐ gent residues in the dis‐ penser drawer.

The appliance does not dry or does not dry cor‐ rectly.

The laundry is full of dif‐ ferent colours fluff.

• Make sure that the flap is in the correct position (UP for powder detergent - DOWN for liquid detergent).

• Make sure you have used the detergent dispenser ac‐ cording the indications given in this user manual.

• Turn the water tap on.

• Make sure the drain filter is not clogged.

• Reduce the laundry load.

• Make sure you have set the correct cycle. if necessary, set again a short drying time.

The fabrics washed in the previous cycle released fluff of a different colour:

• The drying phase helps to eliminate some fluff.

• Clean the clothes with a fluff remover.

In case of an excessive amount of fluff in the drum run the special programme to clean it (refer to “Fluff in the fabrics" for more details).

42 www.electrolux.com

After the check, activate the appliance. The programme continues from the point of interruption.

If the problem occurs again, contact the Authorised Service Centre.

If the display shows other alarm codes, deactivate and activate the appliance. If the problem continues, contact the Authorised Service

Centre.

16.3 Emergency door opening

In case of power failure or functioning failure the appliance door remains locked. The washing programme continues when the power is restored. If the door remains locked in case of failure, it is possible to open it using the emergency unlock function.

Before opening the door:

CAUTION!

Risk of burns! Make sure that the water temperature is not too high and the laundry is not hot. If necessary, wait until they cool down.

To open the door, proceed as follows:

1. Press the On/Off button to switch the appliance off.

2. Disconnect the mains plug from the mains socket.

3. Open the filter flap.

4. Pull the emergency unlock trigger downward once. Pull it downward once again, keep it tensed and, in the meanwhile, open the appliance door.

CAUTION!

Risk of injury! Make sure that the drum is not rotating. If necessary, wait until the drum stops rotating.

5. Take out the laundry and then close the appliance door.

6. Close the filter flap.

Make sure that the water level inside the drum is not too high. If necessary, proceed with an emergency drain (refer to

«Emergency drain» in

«Care and cleaning» chapter).

17. CONSUMPTION VALUES

Stated values are obtained in laboratory conditions with relevant stand‐ ards. Different causes can change the data: the quantity and type of laundry and ambient temperature. Water pressure, the supply voltage and the temperature of inlet water may also affect the washing pro‐ gramme duration.

Technical specifications may be changed without prior notice to improve the quality of product.

ENGLISH 43

During the washing programme, the SensiCare technology can vary the wash duration and the consumption values. For further details see 'The

SensiCare load detection' paragraph in 'Daily Use' chapter.

Programmes Load

(kg)

Energy con‐ sumption

(kWh)

1.70

Water con‐ sumption

(litre)

Approximate pro‐ gramme duration

(minutes)

Cottons 60°C

Cotton Eco

Cotton Energy Saving Pro‐ gramme 60°C1)

Cottons 40°C

Synthetics 40°C

Delicates 40°C

10

10

10

4

4

0.92

1.30

0.78

0.60

85

61

85

55

63

205

275

205

130

91

Wool/Handwash 30°C 1.5

0.35

57 60

1) «Cotton Energy Saving programme » at 60°C with a load of 10kg is the reference pro‐ gramme for the data entered in the energy label, in compliance with 96/60/EC Directive.

18. TECHNICAL DATA

Dimension Width/ Height/ Depth/

Total depth

Electrical connection Voltage

Overall power

Fuse

Frequency

Level of protection against ingress of solid parti‐ cles and moisture ensured by the protective cov‐ er, except where the low voltage equipment has no protection against moisture

600 mm/ 850 mm/ 631 mm/ 660 mm

220-240 V

2200 W

13 A

50 Hz

IPX4

Water supply 1)

Water supply pressure Minimum

Maximum wash load

Maximum dry load

Maximum

Cotton

Cotton

Synthetics

Cold water

0.5 bar (0.05 MPa)

8 bar (0.8 MPa)

10 kg

6 kg

4 kg

Spin Speed Maximum spin speed 1550 rpm

1) Connect the water inlet hose to a water tap with a 3/4'' thread.

44 www.electrolux.com

19. ACCESSORIES

19.1 Available in www.electrolux.com/shop or from authorised dealer

Only appropriate accessories approved by ELECTROLUX ensure the safety standards of the appliance. If unapproved parts are used, any claims will be invalidated.

19.2 Fixing plate kit

If you install the appliance on a plinth that is not an accessory supplied by

ELECTROLUX, secure the appliance in the fixing plates.

Read carefully the instructions supplied with the accessory.

19.3 Pedestal with the drawer

To raise your appliance and make loading and unloading laundry easier.

The drawer can be used for laundry storage e.g.: towels, cleaning products and more.

20. ENVIRONMENTAL CONCERNS

Recycle materials with the symbol .

Put the packaging in relevant containers to recycle it. Help protect the environment and human health by recycling waste of electrical and electronic appliances. Do not dispose of appliances marked with the symbol with the household waste. Return the product to your local recycling facility or contact your municipal office.

*

www.electrolux.com/shop

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals